PRODUCT DATA SHEET SikaQuick® VOH
Fast Setting, one component, cementitious vertical and overhead repair mortar with superior high build properties PRODUCT DESCRIPTION SikaQuick® VOH is a fast setting, one component, ready-to-use repair mortar for vertical and overhead ... powder and liquid is …
Download PRODUCT DATA SHEET SikaQuick® VOH
Information
Domain:
Source:
Link to this page:
Documents from same domain
PRODUCT DATA SHEET Sika® Primer-207
usa.sika.comIMPORTANT NOTE If Sika® Primer-207 is used below 5 °C further testing under worst case conditions are man-datory. Sika® Primer-207 is a moisture reactive sys-
Sikadur Epoxies Application Guide - Sika …
usa.sika.comSikadur® Epoxies Application Guide LPL = Long Pot Life cps = centipoise Reference approximate viscosity water = 1 cps olive oil = 100 cps motor oil = 1000-2000 cps Crack Repair Patching Overlay Bonding Adhesive Anchor Bolts Base Plate Grouts USDA Approved Potable Water Approved ASTM C-881 Interior Exterior Int. Exterior Type …
Liquid Seam Sealant - Sika AG
usa.sika.comConstruction Sikaflex® 110 Liquid Seam Sealant Description Sikaflex 110 Liquid Seam Sealant is a non-shrinking, 100% solids, solvent free polyether based, moisture curing, elastomeric sealant. It forms a weather-tight seal when applied over sheathing board joints.
Part 1 - General - Sika AG
usa.sika.comA. Sikadur Injection Gel as manufactured by Sika Corporation, 1682 Marion Williamsport Road, Marion, Ohio 43302 is considered to conform to the requirements of this specification.
PRODUCT DATA SHEET SikaTop®-123 Plus
usa.sika.com0 g/l (EPA method 24) LIMITATIONS Do not use solvent-based curing compound. Size, shape and depth of repair must be carefully considered and consistent with practices recommended by ACI or ICRI. For additional information on substrate preparation, refer to ICRI Guideline No. 310.2R. If aggressive means of substrate preparation is
SikaSwell S-2 SikaSwell S-2
usa.sika.comApplication Recommended application temperatures: 50°-90°F. Extrude material using Sika MK-5 bulk caulking gun or other approved bulk gun. Cut the nozzle to obtain a triangular extrusion section with a size fulfilling effective needs (or use nozzle included in carton of SikaSwell S-2). Apply a uniform, continuous bead to the hardened concrete.
PRODUCT DATA SHEET Sikalastic®-710 Base
usa.sika.comMetal - Should be thoroughly cleaned by grinding or blast cleaning to near white metal (SSPC SPS-10). Priming Primer Selection - Determine maximum moisture content of concrete substrate by weight with a Tramex CME or CMExpert type concrete moisture meter. Sikalastic® Primer – For concrete decks with a maximum
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comSpecification TT-S-00230C, Type II, Class A. Meets ASTM C-920, Type S, Grade NS, Class 35, use T, NT, O, M, G, I, A. Canadian standard CAN/CGSB 19.13-M87. USES Designed for all types of joints where maximum depth of sealant will not exceed 1/2 in. Excellent for small joints and fillets, windows, door
PRODUCT DATA SHEET Sika® FerroGard®-903
usa.sika.comreinforced, prestressed, precast, post tensioned or marine concrete. Use of Sika® FerroGard®-903: Steel-reinforced concrete, bridges and highways exposed to corrosive environments (deicing salts, weathering) Building facades and balconies Steel-reinforced concrete in or near a marine environment Parking garages
PRODUCT DATA SHEET Sikaflex®-1A
usa.sika.comJoint dimension should allow for 1/4 inch minimum and 1/2 inch maximum thickness for sealant. Proper design is 2:1 width to depth ratio, For use in horizontal joints in traffic areas, the absolute minimum depth of the sealant is 1/2 in. and closed cell backer rod is recommended. Removal Use personal protective equipment (chemical resistant
Related documents
Exterior Insulation and Finish System Application Guide
academy.parexusa.comCementitious-Acrylic Basecoat & Adhesive, pail products mixed with Type I or I-II Portland cement in a ratio of 1 part Basecoat & Adhesive to 1 part cement by weight. Dry Basecoat & Adhesive, bag products, factory blended cementitious dry powder that only requires the addition of water. Waterproof Basecoat
ARDEX K 301 Data Sheet
ardex.co.ukARDEX K301 – Cementitious screed material of use internally and externally EN 13813: CT-C30-F7-A22 Bulk density of powder approx.1.37kg/litre Weight of fresh mortar approx.1.94kg/litre Initial Set (Vicat) approx. 40 minutes Final Set (Vicat) approx. 2 hours Compressive Strength After 7 days 20.0 N/mm2 After 28 days 30.0 N/mm2
PRODUCT DATA SHEET SikaGrout®-214 - sika egypt
egy.sika.comHigh Performance, Non Shrink, Expanding Cementitious Grouting Mortar DESCRIPTION Sikagrout® -214 is a high performance, shrinkage com-pensating, ready to use grouting mortar. Consisting of : A blend of cement & fillers, Properly graded quartz aggregates, And Special additives. When mixed with water, the product forms a fluid
INSTALLATION INSTRUCTIONS - Shaw Floors
smartcorefloors.comUse cementitious patching and leveling compounds that meet or exceed maximum moisture level and pH requirements. Use of ... The surface must be hard and dense, and free from powder or flaking. 2. New concrete slabs must be dry. Maximum moisture level per CaCl test method is 8 lbs. per 1000 in 24 hr. Maximum level for
SikaTop Seal 107 - Sika USA - Protecting the past ...
usa.sika.comDescription SikaTop® Seal 107 is a two-component, polymer-modified, cementitious waterproofing and protective slurry mortar for ... Mix in a clean container by slowly adding the powder component to the liquid component and mixing with slow speed drill and mixing paddle.
Current Active Standards - Society for Protective Coatings
www.sspc.orgMeasurement of Dry Coating Thickness on Cementitious Substrates Using Ultrasonic Gages July 2015, ed. rev. February 2018 SSPC-PA Guide 10 : Guide to Safety and Health Requirements for Industrial Painting Projects August 2008 . SSPC-PA Guide 11 : Protecting Edges, Crevices, and Irregular Steel Surfaces by Stripe Coating August 2008 . SSPC-SSPC-PA 12
Five Star Grout - Weber UK
www.uk.weberFive Star Grout is a premixed cementitious grout developed for applications where an economical grout with good flow and strength is required. Five Star grout is based on specially selected Portland cements, graded aggregates and admixtures including a special form of carbon. Five Star Grout is designed primarily as a flowing grout but