Search results with tag "Cementitious"
PRODUCT DATA SHEET SikaTop® Seal-107 IN
ind.sika.commodified cementitious liquid applied waterproofing coating system. It comprises of a liquid polymer and a cement based mix incorporating special admixtures. It is applied to concrete and mortar to prevent water in-filtration. USES Interior and exterior waterproofing and damp-proof-ing of concrete, cementitious rendering, brickwork and blockwork
PROJECT : BILL OF QUANTITY - WATERPROOFING
www.ipwtwaterproofing.comnon-shrink cementitious waterproof compound. The third part consisting of making vata (gola) at the interface joint of the slab and wall with ZUPA “Repaira”, a specialised non-shrink cementitious waterproof compound. The fourth part consisting of sealing all joints of outlet drain pipe, etc. with ZUPA
CHAPTER 9 PHYSICAL PROPERTIES OF LIGHTWEIGHT …
www.escsi.orgphenomena (1) the mechanical adhesion of the cementitious matrix to the surface of the aggregate and (2) the variation of physical and chemical characteristics of the transition layer of the cementitious matrix close to the aggregate particle. Curing, internal-Internal curing refers to the process by which the hydration of
CONTENTS
www.palcotrading.comCEMENTITIOUS RENDERING CURING COMPOUND CONMIX RECON PH polymer modified, cementitious thin fairing coat repair mortar for concrete surfaces, plaster surfaces, etc. Available: 5 kg / 25 kg CONMIX RECON HS non-shrink repair mortar containing fibres to provide high strength, fine, smooth repaired surfaces. Available: 5 kg / 25 kg CONMIX RECON RESC
§501 Section 500 PORTLAND CEMENT CONCRETE
www.dot.ny.govA. Cementitious Materials. Use only cementitious materials meeting §701-01 whose brand name ... aggregates may be reprocessed or reworked to meet the gradation requirements. a. Concrete Sand. Use only sand meeting the requirements of §703-07, …
Solar Reflectance Values of Concrete
www.cement.orgslump, 4% air content, 0.47 water-cementitious material ratio (w/em), and 0.40 cementitious material-fine aggregate ratio (em/fa). The mixtures were chosen to concentrate on combinations of constituent materials that would produce concrete with low solar reflectance. Table 1 …
Aggregates for Concrete
www.concrete.org3.3.1—Mixing water and water-cementitious material ratio 3.3.2—Absorption and total moisture content 3.3.3—Surface moisture content 3.3.4—Computing mixing water and water-cementitious material ratio 3.3.5—Adjusting batch masses for surface moisture 3.3.6—Alternate definition of surface moisture
ACI MANUAL OF CONCRETE INSPECTION
www.concrete.org6.4—Concrete with supplement ary cementitious materials 6.4.1—Mixture proportioning and control 6.4.2—Water-cementitious material ratio 6.4.3—Aggregate selection 6.4.4—Air entrainment 6.4.5—Quantity of paste 6.4.6—Proportion of fine-to-coarse aggregate 6.5—Proportioning for resistance to severe exposure conditions 6.5.1—Paste ...
Exterior Insulation and Finish System Application Guide
academy.parexusa.comCementitious-Acrylic Basecoat & Adhesive, pail products mixed with Type I or I-II Portland cement in a ratio of 1 part Basecoat & Adhesive to 1 part cement by weight. Dry Basecoat & Adhesive, bag products, factory blended cementitious dry powder that only requires the addition of water. Waterproof Basecoat
PRODUCT DATA SHEET SikaGrout®-215 - Sika Malaysia
mys.sika.comPUMPABLE SHRINKAGE COMPENSATED CEMENTITIOUS GROUT DESCRIPTION SikaGrout®-215 is a pumpable dual-shrinkage com-pensated, self-levelling, prebagged cementitious grout with extended working time to suit local ambient tem-peratures. USES SikaGrout®-215 is suitable for repairs to the following concrete structures: Machine foundations
SPECIFICATIONS FOR REINFORCED CAST-IN-PLACE CONCRETE
www.gov.mb.ca.1 Cementitious content in kilograms per cubic metre or equivalent units for each type of cementitious material. .2 Designated size, or sizes, of aggregates, and the gradation. .3 Aggregate source location(s). .4 Weights of aggregates in kilograms per cubic metre or equivalent units. Mass of aggregates is saturated surface dry basis.
MORTAR COLORS - Solomon Colors
www.solomoncolors.comSolomon Colors A, H, & X Series Concentrated Mortar . Colors are pure mineral pigments designed to be used . with all cementitious material, whether it may be type , S, M or O strength masonry cement or Portland and lime . mixtures. The pre-measured unit concept of SGS mortar . colors provides uniform color control with the cost-saving
How to Properly Insulate a Slab
www.phrc.psu.edu5. Perma‐Bond Complete (foam plus factory adhered cementitious coating) 6. FP Ultra Lite panels (factory coated foam panels) from StyroIndustries 7. Protecto Bond peel‐and‐stick membrane Source: Martin Holladay, GB 8. EnergyEdge 45 • Slab insulation is required when: – The space above is conditioned
Acrylic Latex Admixture for Mortar and Concrete
www.mapei.comAcrylic Latex Admixture for Mortar and Concrete DESCRIPTION Planicrete AC is a one-component, concentrated liquid latex admixture used to enhance the performance of cementitious repair mortars, plasters, stuccos,
Effects of Substances on Concrete and Guide to Protective ...
cdnassets.hw.netguidelines to protective treatments. ... of polymer-modified concrete, greatly reduce the permeability of concrete to many corrosive chemicals. A typical dosage of latex ... cementitious material often range from 15% to 25% for Class F fly ash, 15% to 40% for Class C fly ash, 35% to 50% or more for slag, ...
MASTERFLOW ®®®® 830 - groutspecialist.com.au
groutspecialist.com.auMASTERFLOW ®®®® 830 Cementitious high strength non-shrink precision grout DESCRIPTIONDESCRIPTION MASTERFLOWMASTERFLOW 830 830 830 is a non shrink precision grout
Fosroc Conbextra GP constructive solutions
www.fosroc.comConbextra GP Fosroc Conbextra GP constructive solutions General purpose non-shrink cementitious grout Uses Conbextra GP general purpose grouting is used where it is essential to eliminate shrinkage when completely filling the
Division 9 Materials - Washington State Department of ...
www.wsdot.wa.govcementitious material; (MS) indicates moderate sulfate resistance. 3. Type IT(PX)(LY), where (PX) equals the targeted percentage of pozzolan, and (LY) equals the targeted percentage of limestone. The pozzolan (PX) shall be Class F fly ash and shall be a maximum of 35 percent. (LY) shall be a minimum of 5 percent and a maximum of 15 percent.
Five Star Grout - Weber UK
www.uk.weberFive Star Grout is a premixed cementitious grout developed for applications where an economical grout with good flow and strength is required. Five Star grout is based on specially selected Portland cements, graded aggregates and admixtures including a special form of carbon. Five Star Grout is designed primarily as a flowing grout but
304R-00 Guide for Measuring, Mixing, Transporting, and ...
dl.mycivil.ir(Mielenz 1994; Lovern 1966). If the water-cementitious materials ratio (w/cm) is kept constant, an increase in unit water content increases the potential for drying-shrinkage cracking, and with this cracking, the concrete can lose a portion of its durability and other favorable characteristics, such as monolithic properties and low permeability.
Batching, Mixing, Transporting, and Handling Concrete ...
scetcivil.weebly.compercentages of accuracy: cementitious material ±1%, aggregates ± 2%, water ±1%, and admixtures ± 3%. Equipment should be capable of measuring quanti-ties within these tolerances for the smallest batch regu-larly used as well as for larger batches (Fig. 10-1). The accuracy of scales and batching equipment should be
LifeProof Vinyl Plank INSTALLATION INSTRUCTIONS
images.thdstatic.comexcessive voids or low areas using a non-gypsum, cementitious based leveling compound. Allow the leveling compound to dry thoroughly before beginning the LifeProof Vinyl Plank installation. Follow the manufacturer’s instructions to be sure it is appropriate for the application. C. Subfl oors must be structurally sound without defl ection.
NON-SHRINK GROUTING 03 62 00 - QUIKRETE
www.quikrete.comSpecimens of Cementitious Mixtures • ASTM C939 Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method) • ASTM C1090 Standard Test Method for Measuring Changes in Height of Cylindrical Specimens from Hydraulic-Cement Grout • ASTM C1107 Standard Specification for Packaged Dry, Hydraulic-Cement Grout ...
Specification 501 Pavements 18 January 2022
www.mainroads.wa.gov.auSP43 CEMENTITIOUS MATERIALS FOR CONCRETE 501.03 DEFINITIONS 1. The portion of the road placed above the design Subgrade level including shoulders. Pavement 2. A portion of the pavement placed and compacted as an entity. Pavement Layer 3. One or more layers of material usually constituting the uppermost
ASTM C90, Standard Specification for Load-Bearing Concrete ...
www.uop.edu.jo17.5.3 Standards for Masonry Mortar and Grout ASTM C270, Standard Specification for Mortar for Unit Masonry. This standard covers four types of masonry mortar made from a variety of cementitious materials, including portland cement (ASTM C150), mortar cement (ASTM C1329), and masonry cement (ASTM C91), as well as blended
Current Active Standards - Society for Protective Coatings
www.sspc.orgMeasurement of Dry Coating Thickness on Cementitious Substrates Using Ultrasonic Gages July 2015, ed. rev. February 2018 SSPC-PA Guide 10 : Guide to Safety and Health Requirements for Industrial Painting Projects August 2008 . SSPC-PA Guide 11 : Protecting Edges, Crevices, and Irregular Steel Surfaces by Stripe Coating August 2008 . SSPC-SSPC-PA 12
1. Introduction
www.bca.gov.sgnon-shrink grout and an approved self-adhesive compressible waterproofing strip. In addition, an approved flexible cementitious waterproofing membrane may be used at the inner corner of the intersection between the wall panel and beam/slab for enhanced watertightness performance. Self-adhesive compressible waterproofing strip Non-shrink grout
1.1 REFERENCES 1.2 DEFINITIONS 1.3 SUBMITTALS 1.4 ...
www.wbdg.org2.3.1.6 Other Supplementary Cementitious Materials 2.3.2 Water 2.3.3 Aggregate 2.3.3.1 Normal-Weight Aggregate 2.3.3.2 Lightweight Aggregate 2.3.3.3 Recycled Aggregate Materials 2.3.4 Admixtures 2.4 MISCELLANEOUS MATERIALS 2.4.1 Concrete Curing Materials 2.4.2 Nonshrink Grout 2.4.3 Floor Finish Materials ...
Class C and Class F Fly Ash: Comparisons, Applications ...
mnconcretecouncil.com“filler” effects as well as pozzolanic or cementitious contributions – The test is sensitive to the cement used – Evaluations of the existing strength activity index showed increasing the specification limit to 85% eliminated inert materials (filler effect) – Need to change the time required for testing to accommodate some Class F ash
INSTALLATION INSTRUCTIONS - Shaw Floors
smartcorefloors.comUse cementitious patching and leveling compounds that meet or exceed maximum moisture level and pH requirements. Use of ... The surface must be hard and dense, and free from powder or flaking. 2. New concrete slabs must be dry. Maximum moisture level per CaCl test method is 8 lbs. per 1000 in 24 hr. Maximum level for
IS 2250 (1981): Code of Practice for Preparation and Use ...
law.resource.org2.1 Mortar - Mortar is a homogeneous mixture, produced by intimately mixing cementitious materials, water and inert materials, such as sand, to the required consistency for use in building together with masonry units. 2.2 Lime Mortar - A mortar containing lime and sand.
Fosroc Conbextra GP constructive solutions
fosroc.comGeneral purpose non-shrink cementitious grout Uses Conbextra GP general purpose grouting is used where it is essential to eliminate shrinkage when completely filling the void between a base plate and a substrate. Such an appli-cation would be the grouting of a stanchion and machinery-base plates. It can also be used for anchoring a wide range
Horizontal Directional Drilling - plastic pipe
plasticpipe.orgHowever, unless cementitious agents are added, the thickened mud is no stiffer than very soft clay. Drilling mud provides little to no soil side-support for the pipe. ... Obtain “as-built” drawings based on the final course followed by the reamer and the installed pipeline. The gravity forces may have caused the reamer to go
UL Listing Index Construction Joints
www.grabberman.comE. Cementitious Backer Units* – As an alternate to the gypsum sheathing (Item 2D), n om 1/2 in. or 5/8 in. thick square -edge boards attached to studs with 1 -1/4 in. long corrosion resistant self -tapping wafer - head steel screws spaced 6 in OC. Joints covered with glass fiber mesh tape.
SikaTop Seal 107 - Sika USA - Protecting the past ...
usa.sika.comDescription SikaTop® Seal 107 is a two-component, polymer-modified, cementitious waterproofing and protective slurry mortar for ... Mix in a clean container by slowly adding the powder component to the liquid component and mixing with slow speed drill and mixing paddle.
PRODUCT DATA SHEET SikaTop® Armatec®-110 EpoCem®
gbr.sika.comSikaTop® Armatec®-110 EpoCem® is a cementitious epoxy resin compensated 3-component coating ma-terial with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. USES Suitable for control of anodic areas (Principle 11, method 11.1 EN 1504-9) Suitable in concrete repair as corrosion protection for reinforcement.
Developing together. Building with each other.
www.basf.comCementitious and calcium sulphate-based screeds Non-shrink grouts Non-sag Applications Cement-based ceramic tile adhesives Exterior insulation and fi nishing systems (EIFS/ETICS) Plasters, renders & skim coats BASF Construction Additives and Formulation Know-How for Construction Materials To drive sustainable development,
ARDEX K 301 Data Sheet
ardex.co.ukARDEX K301 – Cementitious screed material of use internally and externally EN 13813: CT-C30-F7-A22 Bulk density of powder approx.1.37kg/litre Weight of fresh mortar approx.1.94kg/litre Initial Set (Vicat) approx. 40 minutes Final Set (Vicat) approx. 2 hours Compressive Strength After 7 days 20.0 N/mm2 After 28 days 30.0 N/mm2
GE-1 Weights Building Materials
dom.dacha-dom.ruAcoustical fiber board (1) 1 Suspended steel channel system (1) 2 ... 1" reinforced regular weight concrete 12.5 ... 7/16" cementitious backerboard 3 Ceramic or quarry tile (3/4") on 1/2" mortar bed (1) 16 Ceramic or quarry tile (3/4") on 1" mortar
Alkali-Silica Reactivity (ASR) Testing (ASTM C1260 / ASTM ...
assets.master-builders-solutions.comis used in ASTM C1260 whereas a combination of portland cement and the SCM under evaluation make up the cementitious materials package in ASTM C1567. Specially prepared mortar beam specimens are placed in a high alkaline solution bath at a temperature of 80 °C (176 °F) for a period of 14 days.
INCRETE SYSTEMS COLORS - Euclid Chemical
www.euclidchemical.comIncrete Systems’ THIN-CRETE GROUT is an easy to use, polymer-modified, cementitious, stampable overlay. With Increte’s . STAMPING TOOLS, THIN-CRETE provides a beautiful array of nature’s unique textures and colors. ... cement, aggregates, method of application and light sources. CHART CC-38. WARRANTY: The Euclid Chemical Company ...
PRODUCT DATA SHEET SikaQuick® VOH
usa.sika.comFast Setting, one component, cementitious vertical and overhead repair mortar with superior high build properties PRODUCT DESCRIPTION SikaQuick® VOH is a fast setting, one component, ready-to-use repair mortar for vertical and overhead applications using specialty cement blends. SikaQuick® VOH LD is a low dust formula also available as a separate
PRODUCT DATA SHEET SikaGrout®-214 - sika egypt
egy.sika.comHigh Performance, Non Shrink, Expanding Cementitious Grouting Mortar DESCRIPTION Sikagrout® -214 is a high performance, shrinkage com-pensating, ready to use grouting mortar. Consisting of : A blend of cement & fillers, Properly graded quartz aggregates, And Special additives. When mixed with water, the product forms a fluid
Alkali-activated cementitious material and concrete
ict.concrete.org.ukThe PAS is intended for use by construction material suppliers, designers and specifiers to enable AACMs to be developed and the most appropriate AACMs to be utilised for different applications.
Cementitious Stabilization - Transportation Research Board
onlinepubs.trb.orgA2J01: Committee on Cementitious Stabilization Chairman: Roger K. Seals, Louisiana State University Cementitious Stabilization DALLAS N. LITTLE, Texas A&M University ERIC H. MALES, National Lime Association JAN R. PRUSINSKI, Portland Cement Association BARRY STEWART, American Coal Ash Association The principal materials used for the cementitious stabilization and modification of highway
Similar queries
SikaTop® Seal-107, Cementitious, PROJECT : BILL OF QUANTITY - WATERPROOFING, Shrink cementitious, Characteristics, Shrink, Section 500 PORTLAND CEMENT CONCRETE, Aggregates, Solar Reflectance Values of Concrete, Exterior Insulation and Finish, Powder, Sikagrout, Cementitious grout, MORTAR COLORS, Mortar . colors, Acrylic Latex Admixture for Mortar and Concrete, Of cementitious, Concrete, Guidelines, Polymer, Modified concrete, MASTERFLOW ®®®® 830, MASTERFLOW ®®®® 830 Cementitious, Grout, Non shrink, Shrink cementitious grout, Division 9 Materials, LifeProof Vinyl Plank INSTALLATION INSTRUCTIONS, NON-SHRINK, QUIKRETE, Specification 501 Pavements, Mortar, INSTALLATION INSTRUCTIONS, Fosroc Conbextra GP constructive solutions, General purpose non-shrink cementitious grout, General purpose, Directional, Based, UL Listing Index Construction Joints, Sika, Armatec®-110, Developing together. Building with each other, BASF, ARDEX K 301, ARDEX K301, Fiber, Reinforced, Weight, ASTM, Alkali-activated cementitious material and concrete, Material, Cementitious stabilization