Product Knowledge Guide Plastics
S Socket SPG Spigot 1/4 bend 90-degree bend 1/6 bend 60-degree bend 1/8 bend 45-degree bend 1/16 bend 22.5-degree bend. Products Offered 8 *Non-Pressure ... Solvent Weld Joints • Solvent cements must meet ASTM D 2564. • Primer is required. • …
Download Product Knowledge Guide Plastics
Information
Domain:
Source:
Link to this page:
Documents from same domain
Cast Iron - Charlotte Pipe
www.charlottepipe.com2 Cast Iron Installation As the leading manufacturer of cast iron soil pipe and fittings, Charlotte Pipe and Foundry can be your one-stop source for all your cast iron …
ChemDrain - Charlotte Pipe
www.charlottepipe.com2 INTRODUCTION ChemDrain® Technical Manual Charlotte Pipe and Foundry is a privately held company committed to providing the highest quality products and service to the plumbing industry.
Cast Iron SoilPipeFit Handbook
www.charlottepipe.comCAST IRON SOIL PIPE AND FITTINGS HANDBOOK Revised and Edited under the direction of the TECHNICAL ADVISORY GROUP …
Plastics Technical anual - Charlotte Pipe
www.charlottepipe.com42 DESIGN & ENGINEERING DATA Plastics Technical anual The operating pressure of PVC and CPVC pipe will be reduced as the operating temperature increases above 73° F. …
El Sistema Invencible. Hierro Fundido - Charlotte Pipe
www.charlottepipe.com4 TABLA DE CONTENIDOS Instalación de Hierro Fundido PROCEDIMIENTOS DE INSTALACION PARA HIERRO FUNDIDO Métodos de Corte para Tubería de Hierro Fundido..... 33-34
Piping Max. Operating System Temp. °F - charlottepipe.com
www.charlottepipe.comFor example, the operating pressure for 6” Schedule 80 PVC pipe is 280 psi. If the operating temperature is 140° F, the maximum operating pressure is now 62 psi (280 x .22).
codut KrnP - Charlotte Pipe
www.charlottepipe.comCharlotte Pipe and Foundry Company is the largest manufacturer of DWV pipe and fitting systems in the country, producing the industry’s broadest range of standard and specialty DWV products.
Cast Iron - Charlotte Pipe
www.charlottepipe.com2 Cast Iron Installation As the leading manufacturer of cast iron soil pipe and fittings, Charlotte Pipe and Foundry can be your one-stop source for all your cast iron piping system needs.
DIMENSIONAL CATALOG - charlottepipe.com
www.charlottepipe.com4 ABS Foam Core Pipe ABS Schedule 40 DWV Pipe (For Non-Pressure Applications) ABS 3112 11⁄ 2” x 10’ 031322590 1.900 0.145 27.1 ABS 3112 11⁄ 2” x 20’ 031335180 1.900 0.145 27.1 ABS 3200 2” x 10’ 0313416702.375 37.7 0.154
DIMENSIONAL CATALOG - charlottepipe.com
www.charlottepipe.comPlastic DWV Pipe and Fitting Dimensions All products manufactured by Charlotte Pipe and Foundry Company are proudly made in the U.S.A. This catalog accurately reflects …
Related documents
RUGGED TIGER EYE SYSTEMS
suddendocs.samtec.comweld tab ruggedizing options • Shrouded, polarized and keyed • Surface mount or through-hole tails • High-density, four row design (FOLC/MOLC Series) • Discrete wire assemblies available in single or double row, 28 and 30 AWG PVC or Teflon® wire; contact asp@samtec.com for custom solutions • Cable components (ISDF/CC03) and tooling ...
CONA S - ARI Armaturen
www.ari-armaturen.com• Socket weld ends ....3 ___ acc. to DIN EN 12760 • Butt weld ends ....4 _____ Weld preparation acc. to EN ISO 9692 identification No. 1.3 and 1.5 (Note restriction on operating pressure / inlet temperature depending to design!) Features • Ball float steam trap with level control for the condensate-discharge from
Underground Drainage Systems
www.marleyplumbinganddrainage.comweld joint or as 110mm mechanical or multiflex bends. ... spigot or socket/socket (shown) and can be adjusted from 0°-90°. Inspection chambers ... Start of external drain* 12 12 – 22 45 Rodding eye 22 22 22 45 45 Type 1 access fitting 150 x 100mm – – 12 22 22 Type 2 access fitting
CURE TIMES - Oatey
www.oatey.comThe pipe size, socket fit, ambient temperature, relative humidity, solvent cement used and the system operating pressure should all be considered when determining set up/cure times. Average Handling/Set Up Times for PVC/CPVC Solvent Cements Handling/Set Up Time is the time required prior to handling the joint. In damp or humid weather, allow
C-18 Forged Steel valves
www.ombvalves.comSW Socket Weld SWxNPT SW x NPT NPTxSW NPT x SW SH10 Schedule 10 SH40 Schedule 40 SH80 Schedule 80 SH160 Schedule 160 SHXXS Schedule XXS RF Raised Face - Smooth Finish 3.2-6.3 - Spiral RJ Ring Joint VALVE TY PE 0 Gate, IS&Y 1 Gate, OS&Y 2 Globe, IS&Y 3 Globe, OS&Y 4 Check, Piston 5 Check Ball 6 Check Swing TRI M DESIGN O BTURATOR …
Bellows-Sealed Valves, B Series (MS-01-22;rev N;en-US;Catalog)
www.swagelok.comTube socket weld ends—1/4 to 1/2 in. alloy 400 Tube butt weld ends—1/4 to 3/4 in. alloyFemale VCR® face seal fittings—1/4 and 1/2 in. Integral male VCR face seal fittings—1/4 and 1/2 in. Panel and bottom mounting Technical Data Determined …
VCR Metal Gasket Face Seal Fittings (MS-01-24;rev T;en-US ...
www.swagelok.com4 Weld, VCR, VCO, Pipe, and Vacuum Fittings WELD FITTINGS Ordering Information, Pressure Ratings, and Dimensions Dimensions are for reference only and are subject to change . The E dimension refers to the smallest nominal inside diameter of the part . To order fittings manufactured in accordance with Swagelok Ultrahigh-Purity Process Specification (SC-01) …
Integrally Reinforced Forged Branch Outlet Fittings ...
www.zzsteels.comrequirements for 90 and 45 degree integrally reinforced forged branch outlet fittings of buttwelding, socket welding, and threaded types. 1.2 Fittings manufactured to this Standard Practice are designed to make a fully reinforced branch connection in accordance with applicable piping code requirements, when attached, at an opening in a run pipe by