Programming and Troubleshooting Guide 1 Mastercode 2

Programming and Troubleshooting Guide 1 Mastercode 2

Troubleshooting: Touchscreen Screen activation To activate the screen, use one of the three options below: 1. Touch screen with palm or back of hand until digits illuminate. 2. Touch lower left area of screen (where Checkmark is located) until digits illuminate. 3. Touch screen with three or more fingers until digits illuminate. One-second pause

  Troubleshooting

Installation and User Guide

Programming timeout after five seconds. Attempt programming procedure again. Unsuccessful programming. Keypad flashes red 15 times with 15 beeps* Three incorrect codes entered within one minute. Re-enter code after 60 second keypad lockout. Keypad flashes red with fast beeping sound for three to four seconds. Low battery. Replace batteries.

  Programming, Installation, Keypads

Interior A Assembly ENGLISH F W B Installation and User Guide

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings.

  Guide, Access

Troubleshooting Guide 1 Door Preparation 2

Handing, or latch calibration, is the way that the smart lock learns the orientation of your door (left- or right-handed). A1: The first time the battery is inserted, the lock will perform automatic calibration, or “handing.” You will know the handing is taking place when the latch bolt retracts and extends on its own.

  Smart

Rev 03 Parts List - .NET Framework

4 Install exterior assembly A Route the cable below the latch. Insert the torque blade through the horizontal slot in the latch. D G Secure the mounting plate with the supplied screws. IMPORTANT: Hold the exterior assembly on the outside firmly (or have a second

264 Contemporary ENGLISH Electronic Deadbolt

IMPORTANT: Make sure the latch bolt is fully retracted (in the unlocked position). A2 Optional: Remove square corner face and replace with round corner face (if needed). Ensure A2 snaps into place. A2 A Install latch in door with supplied screws. 1 / 4 ENGLISH 66882 Rev 02 Installation and User Guide Kwikset Technical Support 1-800-327-5625 www ...

  Electronic, Bolt, Deadbolt, Kwikset, Electronic deadbolt

A B C - .NET Framework

want to operate the lock. For new purchases, the current key is the one that was supplied in the box with the purchased lockset. The new key must be the same key type (KW1) as the current key. Consult your local hardware store for more information. Before performing this procedure, make sure the lock is installed on the door. Re-key the lock while

  Locks

Interior A Assembly F ENGLISH W K L M B Installation and ...

and Troubleshooting Guide on the SmartCode 910 page at www.kwikset.com. 2x One green flash with one beep* Three red flashes with three beeps* Two beeps* or or Programming time out. Make sure not to pause for more than 5 seconds during programming. Tip: You can press the Lock button before entering your user code to light up the keypad at night.

  Guide

CLICKER MODEL CLK1 Wireless Keypad - For use with Garage ...

Step 6 Enter your PIN into the keypad. Step 7 Press and HOLD any additional number on the keypad until the indicator light next to the smart-learn button blinks. Note: Do not use the or # keys as a 5th number. Programming is complete. Wait 10 seconds. CLICKER MODEL CLK1 Wireless Keypad - For use with Garage Door Openers

  Wireless, Keypads, Wireless keypad

T490, T590, P43s, and P53s User Guide - Lenovo

2. Numeric keypad Quickly input numbers. 3. Fingerprint reader* Log in to your computer with enrolled fingerprints. See “Use the fingerprint reader (for selected models)” on page 44. 4. Trackpad Perform finger touch and all the functions of a traditional mouse. See “Use the trackpad” on page 19. 5. NFC label*

  Keypads, Lenovo