REVISION J - Samtec Microelectronics

REVISION CF SSW-1XX-XX-XXX-X-XX-XXX-XX

this document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …

  Xx xxx x xx xxx xx

HIGH MATING FTSH–125–01L–DVEJ CYCLES SMT …

(1.27 mm) .050" FTSH–125–01L–DVEJ FTSH–120–01F–DV FTSH110–01–L–DV m . A Sm . Cm m m Sm Sm m . WWW.SAMTEC.COM For complete specifications and

POWER AND VOLTAGE RATING - Samtec …

VOLTAGE and POWER Ratings final 101207.doc 1 OF 13 10/18/2007 D-SCOPE-TECH, INC. POWER AND VOLTAGE RATING SCOPE: The purpose of this document is to take the confusion out of power and voltage ratings in

  Power, Ratings, Voltage, Power and voltage rating, Power ratings

(1.27 mm) .050 FTS SERIES MICRO LOW-PROFILE …

(1.27 mm) .050" FTS SERIES FTS1102L FTS11002FV FTS12201FV FTS11102LVSA Mates with socket strips or IDC cable Impedance matched for high-speed applications

  Series, Profile

REVISION AO FFSD-XX-X-XX.XX-01-X-X-XXX

this document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …

  Revisions, Ffsd xx x xx, Ffsd, Xx 01

SFM110–02–L–D–A SFML125–T2–LD–LC …

(1.27 mm) .050" SFML125–T2–LD–LC SFM–125–02–L–SH SFM110–02–L–D–A SFML115–T2–LD–LC Choice of SMT or through-hole tails Locking feature

  Sfm110 02 l d a sfml125 t2 ld lc, Sfm110, Sfml125

HIGH MATING CYCLES THROUGH-HOLE MICRO …

(1.27 mm) .050" FTSH SERIES Im m f applications ( CLP S) sock ips IC le T r surf m (2.51 mm) .0" O (1.27 mm) .050" m FTSH–120–02–L–D FTSH–120–01–L–D–RA

  Ftsh

HIGH MATING CYCLES HTSW115–05–LQ TSW–209–09F–SRA …

tsw, htsw series tsw–112–07–g–t tsw10910–f–d–ra htsw12013–t–d tsw–11416g–sre, , m . a sm . cm m m sm sm m .

HIGH MATING CYCLES LOW-PROFILE DUAL WIPE SOCKET

(1.27 mm) .050" CLP SERIES T Cw contacts CLP–107–02–F–D–P CLP–130–02–L–D CLP–116–02–F–DH CLP–115–02–L–D S m Lw-pro˜le

HIGH MATING CYCLES (2.54 mm) .100 SMT .025 SQ POST …

tsm series tsm–115–01–t–sh–a tsm–12–02–l–dh–k tsm110–01–t–dv m . a sm . cm m m sm sm m . www.samte.om

  Series

DRAWING REQUIREMENTS FOR DEVICE ONNECTOR …

C ONTENTS 1. General EWCAP Drawing/Drafting Requirements 2. Blade Location Labeling 3. Datum Feature “A” 4. Datum Features of Size “B and C” 5. Connector Floor

  Devices, Requirements, Drawings, Onnectors, Drawing requirements for device onnector

405P 405C 405A - Emerson

dr. size c title boulder, colorado drawing no. approval specials tagging drawing *all dimensions are nominal and are for reference only *unless otherwise specified

  Dimensions, Drawings

Apex v5 Drawing Features Addendum 11-2012

2 Apex can be set to Automatic Dimension Placement mode so the dimension will anchor at the same time the line is anchored. This saves an extra step on each line. Dimensions can be moved after the sketch is completed to ‘clean up’ the drawing and there are several macro dimension

  Feature, 2012, Dimensions, Drawings, Addendum, Apex, Apex v5 drawing features addendum 11 2012

General tolerances for Iinearand angular DIN dimensions ...

Page 2 DIN 7168 3 General tolerances for linear and angular dimensions 3.1 Linear dimensions Table 1. Permissible deviations for linear dimensions, except for external radii and chamfer heights

  General, Dimensions, Angular, Tolerance, Iinearand, General tolerances for iinearand angular

TO-247AC (High Voltage) - Vishay Intertechnology

Package Information www.vishay.com Vishay Siliconix Revision: 01-Jul-13 1 Document Number: 91360 For technical questions, contact: hvm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

  Vishay, Vishay intertechnology, Intertechnology, To 247ac, 247ac

Drawing Standards for Plan/Work Applications Checklist of ...

General Standards Provide and submit one (1) unbound set of plans with wet ink signatures and stamps. Only one (1) set of plans shall be submitted at initial filing.

  Drawings