SCOPE - James Hardie
Insulation and Non-Nailable Substrates SEPTEMBER 2014 #19 The guidance and instructions provided in this technical bulletin are valid for and applicable to James Hardie® products only. James Hardie Building Products Inc. makes no warranty or representation with respect to use of the information contained herein for any use other than with James
Download SCOPE - James Hardie
Information
Domain:
Source:
Link to this page:
Documents from same domain
Page 1 10 231 S. LaSalle Street, Suite 2000 Chicago, IL ...
www.jameshardie.comPage 1 of 10 Date of Issue: 06/01/15 231 S. LaSalle Street, Suite 2000 Chicago, IL 60604 SAFETY DATA SHEET Section 1. Identification Product Identifier: Exterior Fiber-Cement (Medium Density) – Includes all Generation 6 HZ5 and HZ10 products with the following product names: HardiePlank® lap
Fastening Tips for HardiePlank Lap Siding TECHNICAL ...
www.jameshardie.comIMPORTANT: Failure to install and fi nish this product in accordance with applicable building codes and James Hardie written application instructions
30-Year Limited Warranty - James Hardie
www.jameshardie.com1-800-9-HARDIE 10901 Elm Avenue Fontana, CA 92337 30-Year Limited Warranty HardiePlank® HZ5® Lap Siding, HardiePanel® HZ5® Vertical Siding, HardieShingle® HZ5® Siding, HardieSoffit® HZ5® Panels 1. LIMITED WARRANTY. James Hardie Building Products
Finishing James Hardie TECHNICAL BULLETIN Siding …
www.jameshardie.comand is not recommended. For care & maintenance instructions for ColorPlus and primed products refer to James Hardie Tech Bulletin#20 at www.jamehardie.com If a pressure washer is to be used, use wide fan tips only, at low pressures under 1,500 psi and at safe distances. Keep fan nozzle no closer than 6’ to wall. Exercise extreme caution.
NO CAULK - James Hardie
www.jameshardie.comJames Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2). Joint flashing Butt Joint & Horizontal Lap Treatment JUNE 2014 James Hardie does not recommend caulking butt joints or the horizontal overlaps Joint Flashing 6 in. (152.4 mm) wide,
ICC-ES Legacy Report NER-405* Reissued April 2004
www.jameshardie.comICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
Cut time. Not Quality. - James Hardie
www.jameshardie.com®• HardieBacker Cement Board with HydroDefense™ Technology has internal ... (2015/18 IRC P2709, 2015 IPC 417.5 and/or 2018 IPC 421.5). Completed liners shall be flood tested in accordance with code.
Related documents
LIBERTY SBS Application Instructions - BuildSite
www.buildsite.comPolyiso Insulation or DensDeck® DuraGuard LIBERTY™ CAP SHEET LIBERTY™ BASE/PLY SHEET 4" Min 195/8" 131/8" 2" Min Side Lap 4" Min Side Lap 393/8" 393/8" 393/8" Nailable Deck LIBERTY™ MA LIBERTY™ CAP SHEET LIBERTY™ BASE/PLY SHEET 4" Min 9" Max. 18" Max. 1911/16" 2" Min Side Lap 4" Min Side Lap 393/8" Nailable Deck CAP SHEET LIBERTY ...
Insulation Guide: California Title 24, 2020
www.jm.comJM’s broad portfolio of quality insulation products for use in High Performance Attics & Walls includes: www.JM.com Fiberglass Spray Foam Blow-In Polyiso Sheathing Air Handler & Ducts in Attic (vented or unvented) Compliance must be demonstrated via energy modeling with CBECC-RES software. Mandatory minimum R-22 attic insulation
JM XSPECT ISOFOAM APF BOARD
www.jm.comThermal Insulation: Polyiso provides one of the highest R-values per inch of any rigid insulation (R-6.0 at 1 inch). R means resistant to heat flow. The higher the R-value, the greater the insulating power. R-values for JM XSPECT ISOfoam APF are shown in Table 1, and physical properties are shown in Table 2 (see reverse). Lightweight:
Guide to Insulation Sheathing - Energy
www1.eere.energy.govFor unfaced insulation, the permeability is a function of the material thickness. In general most product manufacturers list the permeance of the material based on a thickness of 1 inch. Increasing or decreasing the thickness of the material will affect the permeance. This can become an issue when using XPS foam insulation.