Seismic Design Specification for Buildings, Structures ...
Seismic Design Specification for Buildings, Structures, Equipment, and Systems: 2020 12/31/2019 1 1 General Design Requirements SLAC will use the 2019 California Building Code (CBC) for structural design criteria.1 The 2019 CBC adjusts the level of design based on risk categories from I to IV.
Download Seismic Design Specification for Buildings, Structures ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
Installation, Inspection, Maintenance, and Repair …
www-group.slac.stanford.eduENVIRONMENT, SAFETY & HEALTH DIVISION . 9 December 2015 SLAC-I-730-0A21S-053-R004 1 of 8 . Chapter 14: Pressure Systems. Installation, Inspection, Maintenance, and Repair
Pressure Test Procedures - Stanford University
www-group.slac.stanford.eduAction . Planning . 1. Mechanic : Obtains test pressure after consulting the project engineer : Note: when hydrostatic test is performed on an existing pressure system, the
Sodium Hypochlorite ENVIRONMENT, SAFETY, …
www-group.slac.stanford.eduaziridine, methanol, formic acid, phenylacetonitrile. When combined with an acid or ammonia may ... Chapter 53 | Sodium Hypochlorite Safe Handling Guideline
Used Automotive Battery Requirements - Stanford …
www-group.slac.stanford.eduSLAC National Accelerator Laboratory Environment, Safety, Health, and Quality Division Chapter 17 | Used Automotive Battery Requirements Fleet Services must maintain records for off-site battery shipments, attaching the signed transporter
Laser Controlled Area Requirements - Stanford …
www-group.slac.stanford.eduENVIRONMENT, SAFETY & HEALTH DIVISION . 22 January 2018 SLAC-I-730-0A05S-009-R003 1 of 4 . Chapter 10: Laser Safety. Laser Controlled Area Requirements
Scaffold Erecting and Dismantling Procedure
www-group.slac.stanford.eduThe purpose of this procedure is to ensure scaffolding is adequate for the work to be performed and properly erected and dismantled. It covers selecting, erecting, and dismantling all types of scaffolds.
Ergonomic Evaluation Procedures - Stanford University
www-group.slac.stanford.eduWorker and supervisor discuss results of ESH Course 291 workstation self- assessment and implement identified workstation corrective actions When warranted or desired, requests ergonomic evaluation by calling OHC at ext.
ESH Project Review Procedure - Stanford University
www-group.slac.stanford.eduENVIRONMENT, SAFETY & HEALTH DIVISION . 27 May 2015 SLAC-I-720-0A24C-001-R008 1 of 9 . Chapter 1: General Policy and Responsibilities. ESH Project Review Procedure
Work Planning and Control Procedure - Stanford University
www-group.slac.stanford.eduENVIRONMENT, SAFETY & HEALTH DIVISION . 28 September 2018 SLAC-I-720-0A21C-002-R004 1 of 11 . Chapter 2: Work Planning and Control. Work Planning and Control Procedure
Exit Path Requirements - Stanford University
www-group.slac.stanford.eduSLAC National Accelerator Laboratory Environment, Safety & Health Division Chapter 12 | Exit Path Requirements Anchor equipment, furniture, shelf units, and cabinets that …
Related documents
SEISMIC LOAD ANALYSIS - Memphis
www.ce.memphis.eduInstructional Material Complementing FEMA 451, Design Examples Seismic Load Analysis 9 - 3 Load Analysis Procedure (ASCE 7, NEHRP Recommended Provisions) 1. Determine building occupancy category (I-IV) 2. Determine basic ground motion parameters (SS, S 1)
Chapter 3 Pre-Installation, Foundations and Piers
www.oregon.govactivity three seismic design categories have been established in Oregon as shown on Figure 3-2.5(a). o Design Category C – low risk o Design Category D 1 - medium risk o Design Category D 2 – high risk Design category C and D 1 Manufactured dwellings are limited to(1): o 3 feet in height for 75% of the under-floor area, and o 5 feet – 7 ...
Data Center Design and Implementation Best Practices
www.bicsi.orgANSI/BICSI 002-2019 Data Center Design and Implementation Best Practices Committee Approval: January 21, 2019 ANSI Final Action: February 8, 2019
Shear wall Design in Residential Construction: A ...
www.phrc.psu.edurelevant design tables within the IRC for shear wall sizing are R602.10.3(1), R602.10.3(3), and R602.10.5. Table 1: Relevant Tables in the IRC for Designing Shear walls. Category Topic Table Designation . Bracing methods Applicable Methods for Shear walls R602.10.4 Wood studs Size, height and spacing R602.3(5) R602.3.1
Seismic Design Criteria Version 2 - Caltrans
dot.ca.gov1.2: Added “Bridge Categories” 1.2.2: Added “Nonstandard Bridge Features” 1.2.4 : Added “Recovery Bridge” 1.2.5: Added “Important Bridge” 1.3 : Deleted “Bridge Systems” 1.3: Added “Seismic Performance Criteria” 1.4: Added “Design Philosophy” Added “Seismic Design Procedure Flowchart” (new Appendix A) 1.5