Spectifications - pipefittingweb.com
Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 Pipe Threads, General Purpose (Inch)
Download Spectifications - pipefittingweb.com
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pressure Unit Conversion Table - pipefittingweb.com
www.pipefittingweb.comPressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Materials - pipefittingweb.com
www.pipefittingweb.comMaterials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
DIN Flanges - pipefittingweb.com
www.pipefittingweb.comDIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
Forged High Pressure Pipe Fittings
www.pipefittingweb.comForged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net
90° Long Radius Elbow - pipefittingweb.com
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
EN 1092-1 Flanges - pipefittingweb.com
www.pipefittingweb.comFlange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Caps - pipefittingweb.com
www.pipefittingweb.comCaps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows - …
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Concentric and Eccentric Reducers - pipefittingweb.com
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
Related documents
DPV® API 594 Dual Plate Wafer Check Valves
www.deltapacificvalve.comu Dual Plate Design Minimizes Valve Cracking u Design : API 594 Pressure and Reduces Valve Pressure Drop u Body Wall Thickness : API 594 u Spring Loading on Plates Assists Valve Closing u Face-to-Face : API 594 to Ensure Tight Seal and Minimize Slamming u Testing : API 598 u Pin Retaining Plugs Fitted with Graphite u For Fitting Flanges to : ASME B16.5 ...
GC Compact cat. - Galperti
www.galperti.com1 Engineering Solutions... GALPERTI ENGINEERING is an International Company whose business is the design, manufacture and supply of high integrity connectors, forged fittings and flow control products.
FORGED STEEL FLANGES - GARTH INDUSTRIAL
www.garthindustrial.com• 6 • INCHES MILLIMETRES 1 Socket Welding Flanges, sizes NPS 3 1/2 (DN 90) and larger are not covered by ASME/ANSI B16.5. 2 Includes .06" (1.6 mm) raised face. 3 These dimensions correspond to inside diameters of pipe as given in ANSI/ASME B36.10M for Standard Wall Pipe.Thickness of Standard Wall is the same as Schedule 40 in size NPS 10 (DN 250) and smaller.
Product Data Sheet FM-CR/FLGA ANSI B16.36 Orifice Flanges
www.helgem.com.twProduct Data Sheet FM-CR/FLGA ANSI B16.36 Orifice Flanges Flow Measurement Wide range of materials, including ASTM A105N Carbon Steel ASTM A350 LF2 Carbon Steel
150# Flanged Cast Steel Gate Valve - Sharpe® Valves
www.sharpevalves.com10/12 Features • Full port • Outside screw and yoke • Bolted bonnet • Flexible wedge, fully guided integrated seats • Rising stem and non-rising hand-wheel
STANDARDS IN THE VALVE & FITTINGS INDUSTRY
www.turnkeyips.comStandards in the valve industry IE: APP, ANSI, ASTM,MSS STANDARDS IN THE VALVE & FITTINGS INDUSTRY Many standards play an importane in tt rolhe
Section 4 Flanges - AAP Industries
www.aapindustries.com.auwww.aapindustries.com.au 67 FLANGES [4] Temperature / Pressure Ratings ASTM A105 CARBON STEEL PIPE FLANGES TO ANSI B16.5 (BS.1560) FORGINGS TO ASTM A105 — Not recommended for prolonged use above 427°C FORGINGS TO ASTM A350-LF2 — Not to be