SPI (Serial Peripheral Interface) NAND Flash Memory
This low-pin-count NAND Flash memory follows the industry-standard serial peripheral interface, and always remains the same pinout from one density toanother . The command sets resemble common SPI-NOR command sets, modified to handle NAND specific functions and added new features. GigaDevice SPI NAND is an easy-to-integrate
Download SPI (Serial Peripheral Interface) NAND Flash Memory
Information
Domain:
Source:
Link to this page:
Documents from same domain
The HIRK3535O30-G5 is a GaAlAs infrared LED in a miniature ...
www.endrich.comnew Contact for information: Dr. Wolf · Tel. +49(0)7452-6007- 23 · e-mail: t.wolf@endrich.com The HIRK3535O30-G5 is a GaAlAs infrared LED in a miniature SMD package with ceramic substrate. The device has a peak wavelength of 850nm LED spectrally matched with phototransistor or photodiode with or without daylight filter.
Related documents
1747-IN063C-EN-P, Universal Serial Bus (USB) to DH-485 ...
literature.rockwellautomation.comUniversal Serial Bus (USB) to DH-485 Interface Converter 7 Publication 1747-IN063C-EN-P - January 2006 Install the Drivers Before using the 1747-UIC, you must install drivers for both the 1747-UIC interface converter and the USB serial port. To install the drivers: 1. If you have RSLinx version 2.42, or higher, the 1747-UIC drivers are included
AXI IIC Bus Interface v2 - Xilinx
japan.xilinx.comThe LogiCORE™ IP AXI IIC Bus Interface connects to the AMBA® AXI specification and provides a low-speed, two-wire, serial bus interface to a large number of popular devices. This product specification defines the architecture, hardware (signal) interface, software (register) interface, and parameterization options for the AXI IIC Bus
MCP23008/MCP23S08 8-Bit I/O Expander with Serial Interface ...
ww1.microchip.comtemperature, serial bus frequency, etc.) must be met to ensure proper operation. 1.3 Serial Interface This block handles the functionality of the I2C (MCP23008) or SPI (MCP23S08) interface protocol. The MCP23X08 contains eleven registers that can be addressed through the serial interface block ( Table 1-2): TABLE 1-2: REGISTER ADDRESSES
Serial LVDS High-Speed ADC Interface - Xilinx
www.xilinx.comdeserializer components (ISERDESE2 primitives) in 7 series FPGAs to interface with analog-to-digital converters (ADC) with serial, low-voltage, differential signalling (LVDS) outputs. The associated reference design illustrates a basic LVDS interface connecting a Kintex™-7 FPGA to an ADC with high-speed, serial LVDS outputs.
AN0062: Programming Internal Flash Over the Serial Wire ...
www.silabs.com1 Debug Interface Overview 1.1 Serial Wire Debug Serial Wire Debug (SWD) is a two-wire protocol for accessing the ARM debug interface. It is part of the ARM Debug Interface Specification v5 and is an alternative to JTAG. The physical layer of SWD consists of two lines: • SWDIO: a bidirectional data line • SWCLK: a clock driven by the host
MIPI Alliance Specification for Camera Serial Interface 2 ...
caxapa.ruCamera Serial Interface 2 (CSI-2) Draft Version 1.01.00 Revision 0.04 – 2 April 2009 Further technical changes to this document are expected as work continues in the Camera Working Group . Version 1.01.00 r0.04 2-Apr-2009 DRAFT MIPI Alliance Specification for CSI-2
Serial Control Interface Standard (Rev 1.0) - Analog Devices
wiki.analog.comThe defined serial interface shall consist of SCLK, SDIO, CSB and SDO. 4.2.1 CSB CSB is the chip select, an active low signal that selects the slave device with which the master intends to communicate. Typically, there is a dedicated CSB between the master and each slave. CSB is always driven by the master.
MPC5121e Serial Peripheral Interface (SPI)
www.nxp.comMPC5121e Serial Peripheral Interface (SPI), Rev. 0 Description of the SPI module 2 Freescale Semiconductor diodes (LCD), analog-to-digital converter subsystems, etc. The SPI is a very simple synchronous serial data, master/slave protocol based on four lines:
Lab Configuring Basic Switch Settings (Solution)
sites.radford.eduNotice that the VLAN 99 interface is in the down state even though you entered the no shutdown command. The interface is currently down because no switch ports are assigned to VLAN 99. c. Assign all user ports to VLAN 99. S1(config)# interface range f0/1 – 24,g0/1 - 2 S1(config-if-range)# switchport access vlan 99 S1(config-if-range)# exit