Technical Data Sheet
Substrate temperature 5 °C *10 °C *15 °C23 °C40 °C Dried/cured for service Dry to over coat, minimum 6 h 4 h 8 h 4 h 2 h Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks, imprints or other physical damage.
Download Technical Data Sheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
Standard Specification for Seamless Carbon Steel Pipe for ...
www.entech.rs1.1 This specification2 covers seamless carbon steel pipe for high-temperature service (Note 1)inNPS1⁄ 8 to NPS 48 [DN 6 to DN 1200] (Note 2) inclusive, with nominal (average) wall thickness as given in ASME B 36.10M. It shall be permissible to furnish pipe …
General Guidance on the selection and installation of ...
www.hetas.co.uksteel. Single wall stainless steel is certified to EN1856-2.The vitreous enamel coating should comply with the recommended requirements for high resistance to heat in BS1344 part1:1994 part 7:1984 and acid resistance BSEN 14483-1:2004. The European Standard for vitreous enamel low carbon steel flue pipes is BS60009-1989. Ceramic Chimney Systems
Piping material for hydrogen service - W. M. Huitt Co
www.wmhuittco.comconsiderations are hydrogen attack and the high degree of concern with regard to leak potential. Carbon steel is acceptable for use in hydrogen service when operating temperatures remain below 500°F. Hydrogen attack occurs when hydrogen is contained under high partial pressure in combination with high temperatures.
JIS G3456 Carbon Steel Pipes for High Temperature Service
www.tubesolution.comJIS G3456 Carbon Steel Pipes for High Temperature Service 1. Scope This Japanese Industrial Standard specifies the carbon steel pipes, hereinafter referred to as the "pipes", mainly used for piping at a temperature over 350℃. Remarks 1. When previously agreed upon by the manufacturer, the purchaser may designate one or all of the ...
STEEL PLATES - steel-n.com
www.steel-n.comSTEEL PLATES. 33. 34 35. 36 37. 38 42. 45 46. 47 49. 50 51. 52 53. 54 55. 56 58. 59 60. 62 72. Contents. Pressure Vessel. vailable Steel GradesA R&D ...
Casting Material Stainless Steel ASTM A351 CF8, ASTM A743 ...
www.castingquality.comCasting Material: Stainless Steel CF8 ... temperatures of 800 to 1600oF as a result of service or welding. High impact strength is retained at cryogenic temperatures, while ... Centrifugal Casting mainly produce the pipes or pipe figure products, such as ductile iron pipe, cast iron soil pipe, glass roller, Furnace Roller and radiant ...
CHAPTER 7 FIXED FIRE EXTINGUISHING INSTALLATIONS
assets.publishing.service.gov.ukambient temperature is near or above the critical temperature which for CO. 2 is 30.5 o C. If the weighing method is used, each cylinder weight and the ambient temperature should be recorded in the service report to allow a comparison to . be made at the next check interval.
Training manual Trouble Shooting - Rational AG
portal.rational-online.comService 10 (SC Pump) 23 Service 11 (CDS Sensor) 24 Service 25 (Cleanjet Pump) 25 ... - Pipes and hoses from cabinet to Pressure sensor P1 might be blocked with fat or dirt particles. ... - Temperature of Quenching sensor B2 must react directly to cold water spray when quenching is active; if temperature remains high check positioning of ...
U001en Hot-Rolled Steel Sheets and Coils
www.nipponsteel.comOur Hot-Rolled Steel Sheets and Coils are applied to a wide range of applications such as, automobiles, electrical appliances, construction materials, containers, and steel pipes, and receive high acclaim from our customers for its excellent quality.
ASTM A106/A 106M GR. B SEAMLESS CARBON STEEL PIPES
www.ctstubes.comASTM A106/A 106M Standard Covers Seamless Carbon Steel Pipe for high-temperature service in NPS 1/8 TO NPS 48(DN6 to DN1200) inclusive, with nominal (average) wall thickness as given in ASME B 36.10M.