TECHNICAL DATA SHEET ISSUED BY TIMBER ... - Proudly …
ensure that their products satisfy Australian Standards and have the relevant minimum mechanical properties including the following:-Hardwood – Stress Grade F22, (characteristic bending strength f’b = 65 MPa, Modulus of elasticity E = 16000 MPa) and Joint Group JD2. Examples - spotted gum, ironbark, blackbutt, kwila and merbau.
Download TECHNICAL DATA SHEET ISSUED BY TIMBER ... - Proudly …
Information
Domain:
Source:
Link to this page:
Documents from same domain
TECHNICAL DATA SHEET ISSUED BY TIMBER …
www.hyne.com.au©TIMBER QUEENSLAND LIMITED TECHNICAL DATA SHEET 19 PERGOLAS AND CARPORTS Revised March 2014 Page 3 PERGOLA OR CARPORT BEAMS Tables 2L and 2H list the sizes and spans for pergola or carport beams in low wind speed and higher wind speed areas.
06 - Treated and Engineered Timber Products | …
www.hyne.com.au06 Technical Design Guide issued by Forest and Wood Products Australia Timber-framed Construction Sacrificial Timber Construction Joint
TECHNICAL DATA SHEET ISSUED BY TIMBER …
www.hyne.com.au©TIMBER QUEENSLAND LIMITED TECHNICAL DATA SHEET 7 TIMBER DECKS - COMMERCIAL, INDUSTRIAL & MARINE Revised August 2017 Page 2 3. Hardwood posts and framing containing more than 10% cross-section area of
TECHNICAL DATA SHEET ISSUED BY TIMBER …
www.hyne.com.au©TIMBER QUEENSLAND LIMITED TECHNICAL DATA SHEET 15 SPECIFYING TIMBER Revised March 2014 Page 2 TERMITES Termite management of all building shall be in accordance with the
The characteristic properties of our glue …
www.hyne.com.aucharacteristic design properties suitable for limit state design in accordance with as1720.1 date of issue: july 2017 this document supersedes all previous versions
TECHNICAL DATA SHEET ISSUED BY TIMBER …
www.hyne.com.au©TIMBER QUEENSLAND LIMITED TECHNICAL DATA SHEET 28 MOISTURE IN TIMBER Revised March 2014 Page 1 An understanding of the way in which moisture in timber affects in-service performance is important as it
The requirements for handling and storing Glulam …
www.hyne.com.auTECHNICAL DATA SHEET #5 DATE OF ISSUE: JULY 2016 THIS DOCUMENT SUPERSEDES ALL PREVIOUS VERSIONS The requirements for handling and storing Glulam products.
TECHNICAL DATA SHEET ISSUED BY TIMBER …
www.hyne.com.au©TIMBER QUEENSLAND LIMITED TECHNICAL DATA SHEET 9 TIMBER RETAINING WALLS Revised March 2014 Page 3 BATTER Gravitational forces cause the backfill to slide towards the wall.
TECHNICAL DATA SHEET ISSUED BY TIMBER …
www.hyne.com.au©TIMBER QUEENSLAND LIMITED TECHNICAL DATA SHEET 20 RESIDENTIAL TIMBER FENCES Revised March 2014 Page 3 PLINTH Where a plinth is provided at the base of sound fences, (to enclose
41 - hyne.com.au
www.hyne.com.auWoodSolutions is an industry initiative designed to provide independent, non-proprietary information about timber and wood products to professionals and companies involved in …
Related documents
STRUCTURAL STEEL DESIGN AND CONSTRUCTION
www.wermac.orgStructural Shapes – standard steel configurations produced by steel mills such as wide flanges, channels, angles, pipe, tubes, etc. Structural Steel – the structural elements that make up the frame that are essential to supporting the design loads, e.g. beams, columns, braces, plate, trusses, and fasteners. It does not include for example ...
BUILDER’S GUIDE TO OHS
courses.ownerbuildercentre.com.auVolume 2 Section 3.1.1 Earthworks. The Australian Standard is AS 2870 Residential Slabs & Footings. Don‘t forget the Safety Issues. 2. Drainage – Surface Water Drainage, Subsoil Drainage, Stormwater Drainage If you want to know the detail of compliance – Refer to the Building Code of Australia – Volume 2 Section 3.1.2 Drainage. 3.
STRUCTAflor Installation & Design Manual
img.bretts.com.auAdhesives - The Australian Standard allows for either fl exible or rigid construction adhesive to be used. Fasteners - Screw fi xing is the preferred method, however the Australian Standard allows for either screw or nail fi xing into timber joists. In the building business, your reputation’s only as good as the materials you use.
Pryda Timber Connectors
pryda.com.auAustralian Standards for Residential Timber Frame Construction stipulate a minimum Z275 steel for all sheet metal products used in an internal environment. In areas outside the building envelope that are exposed to repeated wetting (EXTERNAL areas), Pryda’s stainless steel products or equivalent should be consideredSome alternatives .
Pryda Timber Connectors
pryda.com.auAustralian Standards for Residential Timber Frame Construction stipulate a minimum Z275 steel for all sheet metal products used in an internal environment. In areas outside the building envelope that are exposed to repeated wetting (EXTERNAL areas), Pryda’s stainless steel products or equivalent should be consideredSome alternatives .
Installation & Design Manual - Australian Panel Products
www.australianpanelproducts.com.auThe Australian Standard allows for either fl exible or rigid construction adhesive to be used. Fasteners Screw fi xing is the preferred method, however the Australian Standard allows for either screw or nail fi xing into timber joists. In the building business, your reputation’s only as good as the materials you use.
A guide to preventing structural damage
www.qbcc.qld.gov.auStructural damage can result from movement in clay soils caused by ... footings to the Australian Standard AS2870 – 2011 Residential slabs and footings. Footings correctly ... features away from the house. • Direct surface water away from the house. Do not allow water