Technical Data Sheet - Jotun
The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point of the air, measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper drying. The moisture content in the substrate should not exceed 4 % (by weight). The coating should not be
Download Technical Data Sheet - Jotun
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Advertisement
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
STEP: E142 Substrate Mapping and Device Traceability ...
dom.semi.orgrequirements that the Sort Map task force strove to meet in its development. The ... Substrate Mapping standard and a system overview of their components. The current manufacturing environment that is driving the standard and the benefits will be discussed.
Devices, Requirements, Mapping, Substrates, Traceability, E142, E142 substrate mapping and device traceability
Land Grid Array (LGA) Socket and Package Technology
www.intel.com1. Grasp and hold CPU by substrate edge 2. Lint and other loose particulates can be removed using oil-free, low pressure compressed air (follow local safety regulations) 3. Wet lint-free cloth with IPA and wipe package land pads lightly to remove FM •
Schluter -DITRA Installation Handbook 2020 - Lowe's
pdf.lowes.comRequirements maximum spacing of joists, I-joists, or floor trusses is 19.2" (488 mm) o.c. minimum subfloor thickness – 23/32", 3/4" nom. (19 mm) tongue-and-groove with 1/8" (3 mm) gap between sheets Substrate Preparation verify that subfloor panels are properly fastened to framing members any leveling of the subfloor must be done
Nutrition Requirements for the Triathlete
cehsp.d.umn.eduNutrition Requirements for the Triathlete Kaley Peterson, Kayla Docken Performance Nutrition and Weight management Fall 2014 S ... carbohydrates and fats will be discussed since protein contributes only 5-10% of the substrate used during exercise lasting one hour or longer (Howley, Powers, 2012). The factors involved in
REQUIREMENTS FOR PRESERVATION OF SHIP STRUCTURES
www.dcms.uscg.milREQUIREMENTS 3.1 Preservation requirements - general. The Contractor shall abide by the requirements, contained herein, in addition to all other requirements that are specified in individual work items in the specification package, for all work involving surface preparation and coating application 3.1.1 Authorized coating systems.
Generic Requirements for Surface Mount Design and Land ...
www.ipc.orgGeneric Requirements for Surface Mount Design and Land Pattern Standard Developed by the Surface Mount Land Patterns Subcommittee (1-13) of the Printed Board Design Committee (1-10) of IPC Users of this publication are encouraged to participate in the development of future revisions. Contact: IPC 3000 Lakeside Drive, Suite 309S
Surfaces, Design, Requirements, Generic requirements for surface mount design, Generic, Mount
NUTRITION AND GROWTH OF Notes BACTERIA
www.nios.ac.inrequirements and other physiological requirements for growth zdescribe how bacteria grow and multiply zlist the salient features of the bacterial growth curve 3.2 GROWTH OF BACTERIA 3.2.1 Bacterial nutrition ... is known as substrate-level phosphorylation. The energy-rich phosphate
Requirements, Growth, Nutrition, Substrates, Nutrition and growth of