Technical Data Sheet - Jotun
Road Marking Paint Technical Data Sheet 1 Remarks Other systems may be specified, depending on area of use. Contents of packaging with different batch numbers must be mixed together before use. Please refer to the Decorative Sales Department for technical advice. For reflective properties sprinkle Glass beads over wet paint.
Download Technical Data Sheet - Jotun
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
Packaging Guidelines for Clinical Samples
www.fedex.comFollow these instructions for packaging, marking ... Proper packaging is the sole responsibility of the shipper. For more information and comprehensive guidelines, contact the FedEx Dangerous Goods/Hazardous Materials Hotline at 1.800.GoFedEx 1.800.463.3339; press “81” or say “dangerous goods.” (outside the U.S., request to speak to a ...
Steel for packaging Product catalogue
packaging.arcelormittal.comheavier tin coating) it is usual to have a marking (spaced lines) on one side of the strip The tin coating is often flow melted. It gives the Steel for Packaging its attractive brightness. Moreover it makes an alloying layer FeSn 2 at the interface between iron substrate and tin, which improves the corrosion resistance of the tinplate.
Frequently Asked Questions on Wood Packaging Materials
www.cbp.govFrequently Asked Questions on Wood Packaging Materials 11. What is the reason for the WPM regulation? A: Untreated wood poses a significant risk of introducing plant pests, including pathogens, that can be detrimental to agriculture and to …
DEPARTMENT OF DEFENSE STANDARD PRACTICE MILITARY …
www.dla.mile. The 2D (PDF417) bar code is recommended for use in all packaging identification marking and some figures are modified to remove the linear (Code 39) bar codes. f. Packing list requirements are defined to be one of two types: 1) a content packing list for package contents not marked on the packaging, to include sets, kits, and assemblies; 2) a
Regulation of wood packaging material in international trade
www.ippc.intFeb 01, 2019 · 4.3 Treatment and marking requirements for wood packaging material that is reused, repaired ... Wood packaging material covered by this standard includes dunnage but excludes wood packaging made from wood processed in such a …
Package Selection Marking and Labeling Requirements
www.phmsa.dot.govDescribe United Nations (UN) Packaging Standards and Codes Determine Hazard Communication Marking and Labels - 2 - HM215J and UN Harmonization Labels - 3 - Line §172.446 . No Line Old New §172.448 . Text Changes . HM215J and UN Harmonization Markings - 4 - Marine Pollutant
REQUIREMENTS FOR THE PACKAGING AND TRANSPORT OF …
www1.health.gov.auRequirements for the Packaging and Transport of Pathology Specimens and Associated Materials vii Scope The Requirements for the Packaging and Transport of Pathology Specimens and Associated Materials is a Tier 3B NPAAC document and must be read in conjunction with the Tier 2 document Requirements for Medical Pathology Services.The latter is the overarching