Transcription of Technical Data Sheet - Jotun
1 ^(ValidationDate)4272427251AE - BH - DZ - EG - KE - KW - LY - MA - OM -QA - SAOtherApprovedRoad marking PaintProduct descriptionTypeThis is a quick drying, solvent based paint. Based on solvent based acrylic and benefitsCan be used for marking roads and kerbs. Easy to apply. It has UV resistant useIdeal for use on asphalt and concrete roads, primarily for kerbstones, speed humps or other areas with light and kerbsTechnical Data SheetColoursWhite, Black, red and gravitySolids by volume37 2volume% Only for white colour4 L and 20 : 25 kgSaudi : 4 L and 18 LPackaging sizeProduct dataVOC584g/lISO 11890 EUThis is the theoretical value.
2 Tested value will vary depending on test methodology,accuracy of equipment used for testing and test commentsApplication dataThe product can be applied byRoller : : Use airless spray or conventional : Recommended to paint corners and data for airless sprayNozzle "Spray angle degrees65 80 Pressure at nozzle15 MPa (150 kg/cm )Cleaning of painting toolsJotun Thinner No. 7 Date of code:4272 Page: 1/3 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this your nearest local Jotun office, please visit our website at marking PaintTechnical Data Sheet1 Film thickness per coatTypical recommended rangeDry film thickness40-80 mWet film thickness110-210 mFilm thickness will vary and is calculated as spreading /l Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature,wastage during painting spread rate per coat is obtained at minimum dry film thickness and vice Thinner No.
3 7 DilutionMaximum 10 %Conditions during applicationThe temperature of the substrate should be minimum 10 C and at least 3 C above the dew point of the air,measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper drying. The moisture content in the substrate should not exceed 4 % (by weight). The coating should not be exposed to oil, chemicals or mechanical stress until fully timesDrying times are generally related to air circulation, temperature, film thickness and number of coats, and will be affected Recommended data given is, for recoating with the same generic type of In case of multi-coat application, drying times will be influenced by the number and sequence and by the total thickness of previous coats surface should be dry and free from any contamination prior to application of the subsequent drying time is measured by stated values.
4 Relative Humidity (RH) 50 %Surface (touch) dry20 min10 minHard dry60 min30 min15 min7 minDry to over coat, minimum120 min60 min30 minSubstrate temperature10 C23 C40 CDirections for useSurface preparationThe substrate must be sound, clean, dry and free from dust, oil, grease, laitance etc. All traces of form release agents/curing agents must be removed. A light sanding with suitable abrasive material is recommended before application. Any resulting dust/loose particles must be marking Paint : 2 CoatRecommended paint systemDate of code:4272 Page: 2/3 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this your nearest local Jotun office, please visit our website at marking PaintTechnical Data Sheet1 RemarksOther systems may be specified, depending on area of of packaging with different batch numbers must be mixed together before refer to the Decorative Sales Department for Technical reflective properties sprinkle Glass beads over wet product is available in.
5 United Arab Emirates, Bahrain, Kuwait, Qatar, Saudi, Oman, Egypt and LibyaStorageThe product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with and safetyPlease observe the environmental and precautionary notices displayed on the Material Safety Data Sheet for the product has been information regarding health and safety risks and precautions for the use of this product is specified in the product's Safety Data measures, refer to section and storage, refer to section information, refer to section information, refer to section information in this document is given to the best of Jotun 's knowledge, based on laboratory testing and practical experience.
6 Jotun 's products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun 's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the given data without further should always consult Jotun for specific guidance on the general suitability of this product for their needs and specific application there is any inconsistency between different language issues of this document, the English (United Kingdom)version will of code:4272 Page: 3/3 This Technical Data Sheet supersedes those previously Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this your nearest local Jotun office, please visit our website at
