Technical Document Seismic Technical Guide - USG
Guidelines – 12-gauge, galvanized, soft-annealed steel wire – Manufactured in accordance with ASTM A641 – Meets or Exceeds Federal Specification QQ-W-461H Note: 12-gauge hanger wire produced by USG meets these requirements. Performance Data 12-Gauge Wire Wire Tie Failure / Pullout Load Typical 3 wrap tie 1 270 lbs. Tight 3 wrap tie 358 lbs.
Download Technical Document Seismic Technical Guide - USG
Information
Domain:
Source:
Link to this page:
Documents from same domain
USG Fire-Resistant Assemblies Catalog (English) - …
www.usg.com4 USG Fire-Resistant Assemblies Fire Protection USG is the undisputed leader among building material manufacturers in providing products and systems designed to keep people safe from fire.
USG Area Separation Wall Systems Brochure …
www.usg.comArea separation walls between adjoining townhouses must provide fire-resistive ratings to ensure the safety of occupants in adjacent dwellings.
Fire-Resistant Assemblies Brochure (English) - SA100
www.usg.comUser’s Guide Use this brochure to determine fire ratings for CGC products and systems. This brochure provides: — Comprehensive information about fire-rated assemblies
Technical Document Seismic Technical Guide - USG
www.usg.com4 Hanger Wire Attachment Application Anchorage The International Building Code (IBC), through references to ASCE/SEI 7 Minimum Design Loads for Buildings and Other Structures, American Society of Civil Engineers/Structural Engineering Institute (ASCE/SEI), defines
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Light Duty Suspension Systems ASTM C6351 addresses the load carrying capability of main tees, categorizing them as Light, Intermediate or Heavy Duty.
CGC SHAFT WALL SYSTEMS - USG
www.usg.comC-H studs in a progressive manner, with gypsum panels, gypsum fiber panels or cement board applied to the face. All details, specifications and data contained in this literature are intended as a …
USG DUROCK BRAND CEMENT BOARD SYSTEMS
www.usg.comSTANDARDS USG Durock® cement board exceeds ANSI standards for cementitious backer units (CBU). See ANSI A118.9 for test See ANSI A118.9 for test methods and specifications for CBU and ANSI A108.11 for interior installation of CBU.
Manual Técnico USG Tablaroca® (Español)
www.usg.comUSG Manual Técnico USG TABLAROCA® USG SHEETROCK® Manejo, almacenaje, especificación, instalación y recomendaciones generales.
0 ICC-ES Evaluation Report ESR-1222 - USG
www.usg.comThe USG suspended ceiling framing systems described in this report are suspended, exposed framing, concealed ceiling assemblies used in fire-rated and non -resistance -
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Compression Posts USG Donn® Brand Compression Post providesidrig support for a ceiling suspension system in seismic applications. Telescoping compression posts attach to the main tees at each splayed wire location, preventing upward
Related documents
Commercial Kitchen Hoods (Types 1 + 2) Design Guidance
www.slcdocs.comaterials should be steel not less than M.030 (22 gauge), stainless steel not less that .024 (24 gauge), copper weighing . not less that 24 oz. per sq ft, or of any other approved material. IMC 507.5. 3. upports shall be noncombustibleS and capable of supporting the hood, adjacent ductwork, the effluent load and the possible weight of the personnel
YOUR SOURCE FOR COMPLETE LIGHT GAUGE STEEL TRUSS …
www.allspaninc.com…your source for Light Gauge Steel Truss Systems. With today’s demanding architectural designs, intricate roof lines, and aggressive schedules, light gauge steel trusses have become a popular product for architects, engineers, builders and developers. All-Span®, Inc. can design an engineered, pre-fabricated light gauge
Pryda’s Specifi cation Guide for Floor and Rafter Truss …
pryda.com.auPryda Span is manufactured using light gauge metal webs and are lighter than Longreach, but this is considered during the design process. The metal web system can be very cost-effective, especially if the truss chords have reserve capacity, as is often the case. The nail plates and Pryda Span metal webs are made to
Design Guide for Steel Railway Bridges - Steel Construction
www.steelconstruction.info4.6 Truss girder bridges 45 4.7 Direct fastening construction 46 ... 7.4 Restraint systems 83 7.5 Material strength and notch toughness 85 7.6 Slab design 87 ... Most of the detail in the guide relates to (standard gauge) mainline railways and
RIVET HANDBOOK
mae.ufl.eduwhen fastening relatively light gauge materials. BLIND RIVETS RIVET HANDBOOK PAGE 4 ... • Marketers and manufacturers of rivets usually assign their own coding systems, Ajax use an American system, which has become the industry’s most recognised code. ... eg. 73 ASMG is a truss head Aluminium Steel Multi-Grip. There will be more on special ...