TECHNICAL GUIDE
DensGlass Sheathing is available in 1/2” (12.7 mm) thickness and DensGlass® Fireguard® Sheathing is available in 5/8” (15.9 mm) thickness. DensGlass Sheathing is manufactured in a 4’ (1219 mm) width and 8’ (2438 mm), 9’ (2743 mm) and 10’ (3048 mm) lengths. Other DensGlass® Sheathing ©2016 Georgia-Pacific Gypsum LLC Fiberglass Mats
Download TECHNICAL GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
SHAFTLINER FOR SHAFTWALL/STAIRWELL SYSTEMS
www.buildgp.comNote that the edges of the panel are beveled to help guide the panel into the slotted and tabbed section of the stud. 6. Progressively install succeeding studs and panels as described above until the wall section is enclosed. The final panel section may be secured with 1-5/8” (41 mm) Type S screws or tabs from the J track at 24” (610 mm) o ...
TECHNICAL GUIDE - Gypsum, Wood, Lumber, OSB Boards
www.buildgp.comDec 01, 2017 · The unique construction has been shown to withstand delamination, deterioration, warping and job site damage far more effectively than paper-faced gypsum board and other conventional roofing products such as wood fiberboard and perlite. • Provides superior fire protection. • Resists fire and hail damage.
Technical Service Hotline 1.800.225.6119 or www.gpgypsum
www.buildgp.comassembly installation instructions). Primary Uses Because of the superior performance of DensGlass Sheathing, it is specified for exterior walls, ceilings and soffits in a wide variety of applications. These include exterior insulation and finish systems (EIFS); cavity brick or stone veneer applications;
Densglass Shaftliner Area Walls Technical Guide
www.buildgp.comBuilding Code (IBC) Section 706, “Fire Walls.” The Area Separation Wall assembly using DensGlass Shaftliner panels is listed in the UL Fire Resistance Directory under UL Design U373 or U375, the ULC Fire Resistance Directory ULC Design No. W312 and the
Technical Guide: DensArmor Plus® High-Performance Interior ...
www.buildgp.comof Gypsum Panel Products” and ASTM C840 “Standard Specifi cation for Application and Finishing of Gypsum Board for Non-Fire Rated Construction.” For best results, abut DensArmor Plus panels against regular paper-faced drywall only at inside or outside
Stamps/Signatures
www.buildgp.comFIRE SAFETY CAUTION Passing a fire test in a controlled laboratory setting and/or certifying or labeling a product as having a one-hour, two-hour, or any other fire resistance or protection rating and, therefore, as acceptable for use in certain …
DensShield® Tile Backer Installation Instructions
www.buildgp.comDS001. Note: Shower pan or rubber membrane must be adequately sloped to the open drain or weep hole detail to permit proper water drainage. Leave a 1⁄89 (3 mm) gap between DensShield Tile Backer and the shower pan. • DensShield Tile Backer is not to be used in shower curbs. • DensShield Tile Backer panels can be installed in the shower
Technical Service Hotline 1.800.225.6119 or www.densdeck
www.buildgp.commanufacturer’s specifications for full mopping applications and temperature requirements. ... * Testing was done in accordance with FM approvals 4470, Appendix C: Small Scale Tests, Membrane ... with the ANSI/UL 1256 Steiner Tunnel test. For additional information concerning
Related documents
ANALYZED UNIT COST SCHEDULE - Iowa
publications.iowa.govANALYZED UNIT COST SCHEDULE TABLE OF CONTENTS SECTION 4 ... Quality and quantity are the two major factors affecting unit costs in place. A “range” has been given on many ... 6” x 6” Glass Block 34.00 — — — — —
Guidelines and Design Specifications For Crash Barriers ...
www.uttipec.nic.in2.5 To synchronise design with the road users/ pedestrians behavior and needs 2.6 To evolve design with sensitivity to the aspects of aesthetics, sight lines, streetscape, lighting and heritage. 2.7 To consider the cost/ economy factors 2.8 Ease of …
Industrial Diaphragm Valves
cranecpe.comSimplicity of design coupled with more than 85 years of ... factors behind this ... Optimised thickness of diaphragms for superior flexing properties. Two -piece diaphragm construction - PTFE face, with reinforced rubber backing - to increase pressure rating and durability.
Conveyor Belt Manual - IBT Industrial Solutions
www.ibtinc.comAmericas belting adheres to these service factors. This means that if the maximum working tension is 200 PIW, the ultimate tensile strength would be 2,000 PIW. Belting utilizing nylon constructions generally has a service factor of more than 10 to 1. This higher service factor is necessary to overcome some of the inherent properties of nylon,
TruLaser Cost-effective cutting through thick and thin
www.trumpf.comprotective glass status check ensures that you always know the condition of the protective glass of your solid-state laser and can work with consistent quality. Can I cut inferior material? Active Speed Control monitors the cutting process in real time. In the event of sheet thickness variations or quality fluctuations such
USG SECUROCK BRAND GYPSUM-FIBER ROOF BOARD
www.usg.com• 1/4", 3/8", 1/2" and 5/8" thickness—Class A in accordance with UL790 (CAN/ULC-S107). See the UL Building Materials Directory for more information. • 5/8" thickness—Meets requirements of Type X per ASTM C1278 and may be used in P series designs as a thermal barrier. • FM Approved — Complies with requirements of FM 4450 and FM 4470
Washington, D.C. September 2000 Wastewater Technology …
www3.epa.govurban areas) clearing costs, and other factors. Typical pipe materials for small diameter sanitary sewers (8" through 24" diameter) include PVC, vitrified clay, and ductile iron. Typical average costs for sanitary sewers (excluding service connections and manholes) are provided in Table 2. The cost per linear foot in the table is based on an