Technical Guide: DensArmor Plus® High-Performance Interior ...
of Gypsum Panel Products” and ASTM C840 “Standard Specifi cation for Application and Finishing of Gypsum Board for Non-Fire Rated Construction.” For best results, abut DensArmor Plus panels against regular paper-faced drywall only at inside or outside
Download Technical Guide: DensArmor Plus® High-Performance Interior ...
Information
Domain:
Source:
Link to this page:
Documents from same domain
TECHNICAL GUIDE - Georgia-Pacific Building Products
www.buildgp.cominstallation. DensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, fluid applied coatings, self-adhering membranes and spray foam applications. See page 10 for details. Easy to Handle DensGlass Sheathing is lightweight and easy to handle.
SHAFTLINER FOR SHAFTWALL/STAIRWELL SYSTEMS
www.buildgp.comNote that the edges of the panel are beveled to help guide the panel into the slotted and tabbed section of the stud. 6. Progressively install succeeding studs and panels as described above until the wall section is enclosed. The final panel section may be secured with 1-5/8” (41 mm) Type S screws or tabs from the J track at 24” (610 mm) o ...
TECHNICAL GUIDE - Gypsum, Wood, Lumber, OSB Boards
www.buildgp.comDec 01, 2017 · The unique construction has been shown to withstand delamination, deterioration, warping and job site damage far more effectively than paper-faced gypsum board and other conventional roofing products such as wood fiberboard and perlite. • Provides superior fire protection. • Resists fire and hail damage.
Technical Service Hotline 1.800.225.6119 or www.gpgypsum
www.buildgp.comassembly installation instructions). Primary Uses Because of the superior performance of DensGlass Sheathing, it is specified for exterior walls, ceilings and soffits in a wide variety of applications. These include exterior insulation and finish systems (EIFS); cavity brick or stone veneer applications;
Densglass Shaftliner Area Walls Technical Guide
www.buildgp.comBuilding Code (IBC) Section 706, “Fire Walls.” The Area Separation Wall assembly using DensGlass Shaftliner panels is listed in the UL Fire Resistance Directory under UL Design U373 or U375, the ULC Fire Resistance Directory ULC Design No. W312 and the
Stamps/Signatures
www.buildgp.comFIRE SAFETY CAUTION Passing a fire test in a controlled laboratory setting and/or certifying or labeling a product as having a one-hour, two-hour, or any other fire resistance or protection rating and, therefore, as acceptable for use in certain …
DensShield® Tile Backer Installation Instructions
www.buildgp.comDS001. Note: Shower pan or rubber membrane must be adequately sloped to the open drain or weep hole detail to permit proper water drainage. Leave a 1⁄89 (3 mm) gap between DensShield Tile Backer and the shower pan. • DensShield Tile Backer is not to be used in shower curbs. • DensShield Tile Backer panels can be installed in the shower
Technical Service Hotline 1.800.225.6119 or www.densdeck
www.buildgp.commanufacturer’s specifications for full mopping applications and temperature requirements. ... * Testing was done in accordance with FM approvals 4470, Appendix C: Small Scale Tests, Membrane ... with the ANSI/UL 1256 Steiner Tunnel test. For additional information concerning
Related documents
BXUV.U497 Fire Resistance Ratings - SCAFCO Steel Stud …
www.scafco.comJul 01, 2010 · american gypsum co — type ag-c certainteed gypsum inc — proroc type c. certainteed gypsum canada inc — proroc type c. canadian gypsum company — types c, ip-x2, ipc-ar. georgia-pacific gypsum l l c — type dapc lafarge north america inc — types lgfc-c, lgfc-c/a. national gypsum co — types fsk-c, fsw-g, fsw-c, fsmr-c.