Typical Engineering Properties of Polypropylene
Homopolymer 13 – 32 °F -10 – 0 °C Random Copolymer -5 – 20 °F -20 – -5 °C Impact Copolymer - 44 – 20 °F -40 – -5 °C Mechanical Properties Modulus of Elasticity (Young’s Modulus) Homopolymer 183,000 psi 1,300 MPa Copolymer 155,000 psi 1,100 MPa Poisson’s Ratio 0.42 0.42 Hardness
Download Typical Engineering Properties of Polypropylene
Information
Domain:
Source:
Link to this page:
Documents from same domain
THE INEOS SUSTAINABILITY BOOK
www.ineos.com6 THE INEOS SUSTAINABILITY BOOK GENERAL OVERVIEW 7 General overview INTRODUCTION: WHY A SUSTAINABILITY E-BOOK? At INEOS, sustainability is fundamental to how we do business, it is a feature of all of
INEOS HDPE Chemical Resistance Guide
www.ineos.comHDPE Chemical Resistance Guide Reagent 70º F (21º C) (60º C) 140º F V Vanilla extract S S Vaseline S S Vinegar (commercial) S S W Wetting agents S S Whiskey S S Wines S S X Xylene U U Y Yeast S S Z Zinc chloride saturated S S Zinc oxide S S Zinc sulfate saturated S S ...
INEOS PP Chemical Resistance Guide
www.ineos.comLegend: S = Satisfactory O = Some attack U = Unsatisfactory 3 of 5 PP Chemical Resistance Guide Reagent 70 °°°F (21 °°°°C) 140 °°°F (60 °°°°C) 212 °°°F (100 °°°°C) Iodine (dry) S S
INEOS Polypropylene Processing Guide
www.ineos.comPolypropylene Processing Guide . 2 Table of Contents Introduction Part Design Wall thickness Design reinforcements Draft angle Shrinkage Sink marks Undercuts ... Injection Molding Cylinder temperature Injection pressure Injection time Mold temperature Cure …
Tips For Injection Molding INEOS OP HDPE Resins
www.ineos.comTips for Injection Molding INEOS O&P HDPE Resins This tip sheet is intended to provide suggested starting conditions for injection molding of HDPE resins but is not intended to be an all-inclusive guide. Many factors such as part design / mold design, venting
Environmental Stress Crack Resistance of Polyethylene
www.ineos.comEnvironmental Stress Crack Resistance of Polyethylene Introduction to Environmental Stress Cracking and ESCR Over the past decade, high-density polyethylene (HDPE) materials have improved significantly and now meet more stringent
Hoja de datos de seguridad BISULFITO DE SODIO
www.ineos.comHoja de datos de seguridad BISULFITO DE SODIO. 3 . Equipo para combatir el fuego: Como el fuego puede producir productos tóxicos de descomposición térmica, debe usar un aparato de respiración autónomo (SCBA) con máscara facial completa, operado en modo de demanda de presión o presión positiva. Sección 6 – Medidas de liberación ...
Acrylonitrile - Ineos
www.ineos.comSafety Data Sheet (MSDS), available from INEOS, for information on the chemical. For more complete or detailed ... About the Company INEOS is the world’s largest producer and marketer of Acrylonitrile, a component, or “chemical intermediate,” ... 2. Monsanto Chem. Int. Co., ...
DERAKANE FABRICATION GUIDE - Ineos
www.ineos.comand intended to serve as a basic guide to working with these products. Advice on the selection of resins for specific corrosive services is beyond the scope of this guide. For additional guidance, we recommend the Resin Selection Guide for Chemical Resistance, Derakane™ Epoxy Vinyl Ester Resins. Specific material selection guidance
WELCOME TO INEOS GRANGEMOUTH
www.ineos.comused extensively in the petrochemical industry and transformed into bottles and pipes, cabling and insulation, food packaging and by the pharmaceutical industry. Ethylene is also exported from the site via pipelines to the North East and North West of England. Recent investment into the Chemicals business has
Related documents
TYPICAL PROPERTIES OF POLYPROPYLENE (PP)
www.sdplastics.com*Homopolymer polypropylene. **Copolymer polypropylene. ***V-2, V-1, V-0, V-5 grades available. TYPICAL PROPERTIES OF POLYPROPYLENE (PP) ISO or UL Test Property HPP* HPP-filled CPP** CPP-filled ISO1183 Specific gravity 0.90-0.91 0.97-1.27 0.89-0.91 0.98-1.24 ISO62 Water absorption(%) 0.01-0.03 0.01-0.09 0.03 0.01-0.02 ...
POLYPROPYLENE Material Safety Data Sheet
www.acplasticsinc.comNatural Homopolymer Polypropylene, O, P grade polypropylene. Chemical Family Homopolymer Polypropylene Formula [Ch (ch3) ch2-] Proper DOT Shipping Name: N/A DOT Hazard Classification: N/A II. Ingredients Principal Components Percent Threshold L imit Value (Units) Polypropylene (9003-07-0) >99% 10mg/m3 (total dust) III. Physical Data
Polypropylene - Pennsylvania State University
www.personal.psu.eduThe chemical name for polypropylene is poly(1-methylethylene). Common Names Some of the common names for polypropylene include the following: Polypropylene Polypro Polypropene Polipropene 25 Propene polymers Propylene polymers 1-Propene homopolymer Brand Names There are many different brand names for polypropylene used in industry.
SAFETY DATA SHEET Polypropylene (PP)
advancedpetrochem.comPolypropylene (PP) 9003-07-0 >99 % Additives have been incorporated to stabilize the polymer in appropriate amount according to specification of particular grade of Polypropylene. SECTION 4 : FIRST-AID MEASURES Description of necessary first aid measures Skin: Hot molten product stick to the skin immediately.
CHEMICAL RESISTANCE GUIDE - Everything Inside The Fence
everythinginsidethefence.compolypropylene has better stress crack resistance and low temperature toughness than homopolymer at the expense of small reductions in other properties. Most Chemline valves and all the pipe fittings are PP-R. PP-R pipe is also available. The working temperature range of Chemline’s PP-R ball valves is –20 to 80°C (–4 to 176°F) and up to ...
Technical DaTa SheeT Polypropylene - Laminated Plastics
laminatedplastics.comTYPICAL PROPERTIES of POLYPROPYLENE ASTM or UL test Property Homopolymer Co-Polymer Flame Retardant PHYSICAL D792 Density (lb/in³) (g/cm³) 0.033 0.905 0.033 0.897 0.035 0.988 D570 Water Absorption, 24 hrs (%) <0.01 0.01 0.02 MECHANICAL D638 Tensile Strength (psi) 4,800 4,800 4,300 D638 Tensile Modulus (psi) 195,000 - -
Products and Properties - Braskem
www.braskem.comHOMO = Homopolymer RACO = Random Copolymer HECO = Heterophasic Copolymer HCHP = High Crystalline Homopolymer Nomenclature PP • Polypropylene This information refl ects typical values obtained in our laboratories, but should not be considered as absolute or as warranted values. Only the properties and values mentioned on
A Guide to Polyolefin Film Extrusion - LyondellBasell
www.lyondellbasell.comFor homopolymer polyethylenes, the higher the resin density, the higher the degree of crystallinity. High density PE resins have molecular chains with comparatively few side chain branches. This allows the chains to pack more closely together. The result is crystallinity up to 85%. Low density PE resins generally have crystallinity from 35 to 55%.
Polypropylene (PP)
www.opalindia.inPolypropylene - Homopolymer Sector OPaL Grade MFI (g/10 min.) (I 2) Special Characteristics Typical Applications ASTM D1238 Packaging g MH03 3 General Purpose Thermoforming Containers, Rigid Packaging, Flexible Packaging MH05K 5 Anti-Static Heavy wall Parts, Consumer Products, Toothpaste Tubes, Closures, ...