XR-2206 - SparkFun Electronics
Amplitude Modulation Input Impedance 50 100 50 100 k Modulation Range 100 100 % Carrier Suppression 55 55 dB Linearity 2 2 % For 95% modulation Square-Wave Output Amplitude 12 12 Vp-p Measured at Pin 11. Rise Time 250 250 ns CL = 10pF Fall Time 50 50 ns CL = 10pF Saturation Voltage 0.2 0.4 0.2 0.6 V IL = 2mA Leakage Current 0.1 20 0.1 100 A VCC ...
Download XR-2206 - SparkFun Electronics
Information
Domain:
Source:
Link to this page:
Documents from same domain
AT Commands Reference Guide - SparkFun …
www.sparkfun.comAT Commands Reference Guide 80000ST10025a Rev. 0 - 04/08/06 Reproduction forbidden without Telit Communications S.p.A. written authorization - All …
DS1307 64 x 8 Serial Real-Time Clock
www.sparkfun.com1 of 12 100101 FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with …
Advanced User Manual - SparkFun Electronics
www.sparkfun.comusage information and a summary of common commands refer to the Install Guide for a given product. Version 4.77 August 27, 2009 Roving Networks reserves the right to make corrections, modifications, and changes to its products, documentation and services ... Advanced User Manual.
Preliminary Product Specification v1 - SparkFun Electronics
www.sparkfun.comRevision 1.0 Page 3 of 75 nRF24L01+ Preliminary Product Specification Writing Conventions This product specification follows a set of typographic rules that make s the document consistent and easy
Single chip 2.4 GHz Transceiver nRF24L01
www.sparkfun.comPRELIMINARY PRODUCT SPECIFICATION nRF24L01 Single Chip 2.4 GHz Radio Transceiver Nordic Semiconductor ASA - Vestre Rosten 81, N-7075 Tiller, Norway - Phone +4772898900 - …
XBee /XBee-PRO RF Modules - SparkFun Electronics
www.sparkfun.comThe XBee®/XBee-PRO® RF Module was designed to mount into a receptacle (socket) and there-fore does not require any soldering when mounting it to a board. The XBee Development Kits con-tain RS-232 and USB interface boards which use two 20-pin receptacles to receive modules.
GSM/GPRS Module - SparkFun Electronics
www.sparkfun.comThis document gives an overview of the LinkSprite GSM/GPRS module: a miniature, single-side board, quad-band GSM 850/EGSM 900/DCS 1800/PCS 1900 module, ready for integration in various kinds of Fix wireless phones and other wireless devices.
16-Channel Constant-Current LED Driver
www.sparkfun.comA6282 Description The A6282 device is designed for LED display applications. This CMOS device includes an input shift register, accompanying data latches, and 16 MOS constant current sink drivers.
+3.3V Low Power Half-Duplex RS-485 Transceivers with ...
www.sparkfun.com10/15/02 SP3481/3485 Low Power Half-Duplex RS485 Transceivers © Copyright 2000 Sipex Corporation 2 SPECIFICATIONS T AMB = T MIN to T MAX and V CC = +3.3V ± 5% ...
XBee /XBee-PRO RF Modules - SparkFun Electronics
www.sparkfun.comDigi International Inc. 11001 Bren Road East Minnetonka, MN 55343 877 912-3444 or 952 912-3444 http://www.digi.com XBee®/XBee-PRO® RF Modules XBee®/XBee-PRO® RF ...
Related documents
A-Law and mu-Law Companding Implementations Using the ...
www.ti.comfor small amplitude signals consisting of unvoiced phonemes. Concurrently, the telephone system must provide for transmission of a wide range of signal amplitudes, due to the occasional occurrence of high energy voiced phonemes. The accomplishment of these concurrent tasks, within a limited bandwidth, may be achieved via Pulse Code Modulation and
LM555 Timer datasheet (Rev. D) - Texas Instruments
www.ti.comLM555 www.ti.com SNAS548D –FEBRUARY 2000–REVISED JANUARY 2015 6.5 Electrical Characteristics (TA = 25°C, VCC = 5 V to 15 V, unless otherwise specified)(1)(2) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Supply Voltage 4.5 16 V Supply Current VCC = 5 V, RL = ∞ 3 6 V mA CC = 15 V, RL = ∞ 10 15 (Low State) (3) Timing Error, Monostable
CHAPTER 2 SINGLE PHASE PULSE WIDTH MODULATED …
www.tntech.edu2.2.1 Pulse Width Modulation Control The fundamental magnitude of the output voltage from an inverter can be controlled to be constant by exercising control within the inverter itself that is no external control circuitry is required. The most efficient method of doing this is by Pulse Width Modulation (PWM) control used within the inverter.
CHAPTER 1 — BASIC RADAR PRINCIPLES AND GENERAL …
msi.nga.milThe terms PULSE-MODULATED RADAR and PULSE MODULATION are derived from this method of transmission of radio-frequency energy. If the distance to a target is to be determined by measuring the time required for one pulse to travel to the target and return as a reflected echo, it is necessary that this cycle be completed before the pulse immediately
Analog vs. Digital Transmission - WPI
web.cs.wpi.eduCan actually transmit analog data in a similar manner with amplitude-, phase- and frequency-modulated waves. Stallings Fig 4.20. Two reasons: Transmission media may need to use a higher frequency than that used by the data (such as voice) Modulation permits frequency-division multiplexing. CS 513 4 week2-physcont.tex
High-Frequency Waveform Generator - Maxim Integrated
datasheets.maximintegrated.coma ±2.3V control signal, facilitating pulse-width modula-tion and the generation of sawtooth waveforms. Frequency modulation and frequency sweeping are achieved in the same way. The duty cycle and frequen-cy controls are independent. Sine, square, or triangle waveforms can be selected at the output by setting the appropriate code at two
AMPLITUDE MODULATION AND DEMODULATION
svcetedu.orgIt is a type of modulation in which the frequency of the high frequency (Carrier) isvaried in accordance with the instantaneous value of the modulating signal. Consider a sine wave signal vm(t) with pulse w vm(t) = B • sin(w•t) and another sine wave vc(t) with upper pulse: vc(t) = A • …