WESTERN STATES MIDDLE ATLANTIC STATES ... - Pipe Hangers

SB2014 rev 3 - pipehangers.com

Introduction Since 1913 Carpenter & Paterson Inc. has specialized in the design, manufacture, and distribution of a complete line of pipe supports, pipe

  Support, Pipe, Pipe supports

VAR IE - Carpenter & Paterson, Inc. Pipe Hangers & Supports

hangers and supports. We enjoy a position of leadership based upon years of experience in designing and manufacturing quality pipe iupport devices. Our supports have been employed with outstanding success in the chemical, processing and electric power industries.

  Support, Pipe, Hanger, Pipe hangers, Hangers and supports

CATALOG NO. 09MS - Carpenter & Paterson, Inc. Pipe …

for pipe hangers and supports. Multi-Strut channel is easily cut into any desired length. In concrete structures, Multi-Strut continuous concrete inserts provide a continuous slotted channel in floors, walls or ceilings. Multi-Strut insert nuts are placed in the

  Support, Pipe, Hanger, Pipe hangers and supports

Pipe Hanger Hardware

Wire Pipe Hook Page 28 Figure 114 Short Clip Page 29 Figure 124 Riser Clamp Page 30 Figure 125 Pipe Saddle with Yoke Page 31 Figure 125SP Floor Support Page 32 Figure 126 ... PVC BAND HANGER Figure 1A PVC This product is designed to protect the pipe from coming into direct contact with the hanger by having the contact surface PVC coated ...

  Wire, Hanger

PIPE SUPPORT HARDWARE - Carpenter & …

pipe support hardware catalog no. 6.4.1 carpenter & paterson, inc. designers • engineers • manufacturers

  Hardware, Support, Pipe, Pipe support hardware

PIPE SHOES, SLIDES & GUIDES

carpenter & paterson, inc. pipe hangers & supports since 1908 “witch” specialties locations: donora, pa pennsauken, nj saddle brook, nj upper marlboro, md woburn, ma stoney creek, ont.

  Guide, Support, Shoes, Pipe, Slides, Hanger, Pipe hangers, Pipe shoe, Slides amp guides

Electric Heat Tracing - Thermon

heater to the pipe with attachment tape on each side of the elbow. • Pipe Supports: For uninsulated pipe supports, allow twice the length of the support, plus an additional 40 cm of trace heater. Install the trace heater in a loop, following Illustration E as a guide. Insulated pipe supports do not require additional length of trace heater.

  Pipe, Insulated, Insulated pipe

Underground Electric Transmission Lines

High-Pressure, Fluid-Filled Pipe-Type Cable A high-pressure, fluid-filled (HPFF) pipe-type of underground transmission line, consists of a steel pipe that contains three high-voltage conductors. Figure 1 illustrates a typical HPFF pipe-type cable. Each conductor is made of copper or aluminum; insulated with high-quality, oil-impregnated kraft

  Pipe, Insulated

INSTALLATION AND OPERATING INSTRUCTIONS FOR EASY …

sand. Any sections of pipe exposed to the elements should be insulated and protected from wind, as the “wind chill factor” can be a serious impediment to the performance of the heating cable. For example, a large drainpipe can be used to protect the water pipe from wind chill effects and from such damage as

  Pipe, Insulated

Master Flow Ductwork Product Catalog RESMF164

surface to insulated flexible duct or round pipe. • Tacky gasket provides excellent seal. Model # Diameter Carton Qty. Weight UPC Item Code (050206) TTO6 6" 10 11.6 lb 931141 RSC7X6 6" 6 7 lb 931660 Top Take-Offs • For transition from air plenums or rectangular duct to round pipe or insulated flexible duct. • RSC is a “Scotty” take-off.

  Pipe, Insulated

Thermal Processing o Food - Tiselab

Pipe blanchers consist of insulated tubes : through which hot water is circulated. Food is metered into the stream, residence time being controlled by the length of the pipe and velocity of the water. The blancher-cooker has three sections, a ... a pre-set temperature, and then cooled

  Thermal, Processing, Pipe, Insulated, Thermal processing

WETT Pre-Inspection - Baerg’s

Flue pipe The flue pipe is the pipe (usually black) that connects the appliance to the chimney. Measure the distance between the pipe and any combustible construction. Required clearance around the standard single wall flue pipe is 18”. Double wall flue pipes have a sticker stating the required clearance (usually 6”).

  Pipe

Pipe Supports, Guides, Shields & Saddles

Pre-Insulated Support Applications Pipe Hanger Standard Temperature Type Strut Mounted Prefix Insulation Thickness Pipe Type Pipe Size B338 0=1/2” (13mm) CT = Copper Tubing Sizes Nominal Pipe Commercial Duty, 2=1” (25mm) Blank = Std. Sch. 40 Steel or All Purpose Support * 3=11/2” (38mm) Copper Tubing Size 4=2” (51mm) 6=3” (76mm)

  Pipe, Insulated

PRODUCT SELECTION GUIDE - Johns Manville

Micro-Lok® HP Plain is a pre-formed fiberglass pipe insulation manufactured using a state-of-the-art, in-line manufacturing process, creating a highly consistent fiberglass core for reliable, optimized performance during both installation and operation. The insulation may be used on hot or cold pipe systems in concealed or exposed applications for

  Pipe

Pipe Insulation (Hot & Cold) Material Selection & Application

Pipe Insulation (Hot & Cold) Material Selection & Application Revision 2.0, August 2014 Mineral Fibre Glass: Available as flexible blanket, rigid board, pipe covering and other pre-molded shapes. Service temperature range is up to 535°C. Rock and Slag: Rock and slag fibres are bonded together with a heat resistant

  Pipe

Gyrolok Fitting Locator 2 GYROLOK ® Tube Fittings

PST Pre-setting Tool Page51 To cap a tube or plug a fitting, use: HPST Hydraulic Pre-set Tool Page 52 Tools & Accessories LD Leak Detective Page 51 Calibration Fittings fractional tube Page 46 AMS Adapter, SAE fractional tube to • SAE/MS straight thread Page 40 SCF Safety Changer Ferrule Sets frational or metric Page 44