RTD assemblies with extension lead wire - Pyromation

1 Phone (260) 484-2580 FAX (260) 482-6805 or (800) 837-6805 Code RT01 RTD assemblies with extension LeadwireConfiguration Code RT02 RTD assemblies with Sheath Terminations51-12 ORDER CODESThe RTD elements illustrated and described on this page are designed to measure temperature in a variety of process and laboratory applications. These RTDs are specifically designed for use in two different process temperature ranges and will provide accurate and repeatable temperature measurement through a broad range. Low range RTDs are constructed using fluoropolymer-insulated, silver-plated copper internal leads with potting compounds to resist moisture penetration. High range RTDs are constructed with nickel internal leads inside swaged MgO insulated cable to allow higher temperature measurements at the RTD element and provide higher temperature lead protection along the sheath.

2 The following tables allow customer selection of standard element materials, tolerances, sheath diameters, mounting fittings and terminations. Custom-built assemblies with non-standard specifications are available upon :J. BROWNPYROMATION, PAGE RTD-1, FIGURE A====TOLERANCESTITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 ANGULAR DIMDECIMAL DIM .XXXDECIMAL DIM .XXFRACTION DIM DWG. NO. & SHEET NO:B2809016/13/2011 This document is PROPRIETARY toPyromation, Inc. 1/32" " " 2 1"TYPICALSENSITIVEPORTION1-1 Single Platinum RTD elements 1-2 Available Sheath Diameters 316 SSCODETOLERANCE[1]TEMP. RANGEBASE RESISTANCE@ 0 C (R0)TEMPERATURECOEFFICIENTCODE1/8" " " " B(-200 to 200) C100 = 85 C -128384868R3T185 LClass AA(-50 to 200) C100 = 85 C -128384868R5T185L(1/5) Class B(-30 to 150) C100 = 85 C -128384868R1T192 LGrade B(-200 to 200) C100 = 92 C -128384868R3T192 LClass AA(-50 to 200) C100 = 92 C -128384868 RBF185 LClass B(-50 to 200) C100 = 85 C -128384868 RAF185 LClass A(-30 to 200) C100 = 85 C -128384868 RBF195 LClass B(-50 to 200) C1000 = 85 C -128384868R1T185 HGrade B(-200 to 600) C100 = 85 C -128384868 RAT185 HClass A(-100 to 450) C100 = 85 C -128384868R1T192 HGrade B(-200 to 600)

3 C100 = 92 C -128384868[1] Refer to RTD tolerance information in the general information section for calculations to determine specific tolerance at LengthCODE3 Digit 'X' Length1-3 Element ConnectionCODEDESCRIPTION22-wire33-wire4 [1]4-wire[1] Not available in duplex---1-1 Example Order Number:1-4 R5T185L 48 3 1-2(A)1-3-006 PageRTD-2 PageRTD-3 PageRTD-4 PageRTD-5 1-1 Duplex Platinum RTD elements 1-2 Available Sheath Diameters 316 SSCODETOLERANCE[1]TEMP. RANGEBASE RESISTANCE@ 0 C (R0)TEMPERATURECOEFFICIENTCODE3/16" " " B(-200 to 200) C100 = 85 C -1384868R3T285 LClass AA(-50 to 200) C100 = 85 C -1384868R5T285L(1/5) Class B(-30 to 150) C100 = 85 C -1384868R1T292 LGrade B(-200 to 200) C100 = 92 C -1384868R3T292 LClass AA(-50 to 200) C100 = 92 C -1384868 RBF285 LClass B(-50 to 200) C100 = 85 C -1384868 RAF285 LClass A(-30 to 200) C100 = 85 C -1384868 RBF295 LClass B(-50 to 200) C1000 = 85 C -1384868R1T285 HGrade B(-200 to 600) C100 = 85 C -1384868 RAT285 HClass A(-100 to 450) C100 = 85 C -1384868R1T292 HGrade B(-200 to 600) C100 = 92 C -1384868[1] Refer to RTD tolerance information in the general information section for calculations to determine specific tolerance at (inches)

4 TIP (inches)TIPLENGTH(inches)88R481/21/41 1/468R383/83/161 1/448R281/41/81 1/4 REDUCED-TIP RTD'sTable 1-2A lists RTD elements with reduced tip sheaths. To order, use order code numbers from Tbl. 1-2A in place of straight sheath order code numbers from Tbl. 1-2. Other reduced tips are available upon request. EXAMPLE: :J. PERRYPYROMATION, PAGE RTD-1 & RTD-3, FIGURE B====TOLERANCESTITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 ANGULAR DIMDECIMAL DIM .XXXDECIMAL DIM .XXFRACTION DIM DWG. NO. & SHEET NO:B2811014/29/2011 This document is PROPRIETARY toPyromation, P/N: RBF185L483-004-00-15-F3B006-2 1/32" " " 2 XBPhone (260) 484-2580 FAX (260) 482-6805 or (800) 837-6805 Code RT01 Configuration Code RT02 Optional Sheath Mounting Fittings and Bends53-15 ORDER CODESRTD-2 Select Sheath Mounting or Bend Options as desired from tables Order Number.

5 05A,3042 R5T185L483-006 PAGERTD 3 PAGERTD 4 PAGERTD 5 2-1 No Fitting or Bend Options CODE002-3 Re-adjustable Compression FittingsCODETYPENPTSIZE(inches)AVAILABLE SHEATHDIAMETERS(inches)12A316 stainless steel1/81/8, 3/16, 1/412B316 stainless steel1/41/8, 3/16, 1/4, 3/812C316 stainless steel1/21/8, 3/16, 1/4, 3/811 ABrass1/81/8, 3/16, 1/411 BBrass1/41/8, 3/16, 1/4, 3/811 CBrass1/21/4, 3/819 CSpring-loaded SS well fitting1/23/16, 1/4 FEP gland standard 204 C [400 F] max. For lava gland 649 C[1200 F] max. opt. 12A, 12B, and 12C only use letter suffix "L" after compression fitting order code. EXAMPLE: 12AL for lava Miscellaneous OptionsCODETYPEAVAILABLE SHEATHDIAMETER(inches)13A _ _[1]Spring-loaded bayonet fitting1/8, 3/1614 Adjustable flange with brasscompression fitting1/8, 3/16, 1/4, 3/816 ASpring-loaded adjustable bayonetcompression fitting1/8[1] When ordering fixed bayonet fitting specify dimension "A".

6 EXAMPLE: order code 13A06 is for a fixed bayonet adapter with 6" A Fixed BushingsCODEMOUNTINGTHREAD NPT(inches)AVAILABLE SHEATHDIAMETERS(inches)316 SS8A _ _[1]1/81/8, 3/16, 1/48B _ _[1]1/41/8, 3/16, 1/4, 3/88C _ _[1]1/21/8, 3/16, 1/4, 3/88D _ _[1]3/41/8, 3/16, 1/4, 3/8[1] When ordering fixed bushings, specify order code above, plus insertion length "U", as measured from hot tip to bottom of threaded bushing. EXAMPLE: order code 8A06 is 1/8" NPT, 316 SS bushing located 6" from hot Sheath BendsCODEDESCRIPTION2 _ _Sheath bent 45 3 _ _Sheath bent 90 2" minimum hot leg lengthWhen ordering bend options, specify hot leg dim. "A". EXAMPLE: order code 206 is a 45 bend with 6" hot leg. Total sheath length is Table 1 "X" length = hot leg plus cold FITTINGSPEC :J. PERRYPYROMATION, 53 TITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 DWG.

7 NO. & SHEET NO:B2812014/29/2011 This document is PROPRIETARY toPyromation, #: RBF185L483-012-05B-4 TOLERANCESFRACTION DIM =DECIMAL DIM .XX =DECIMAL DIM .XXX =ANGULAR DIM =XAREVISED TITLETR11/19/2019 REVDESCRIPTIONBYDATEFIXED BUSHINGSPEC :J. PERRYPYROMATION, 53 TITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 DWG. NO. & SHEET NO:B2813014/29/2011 This document is PROPRIETARY toPyromation, #: RBF185L483-012-8D05-4 TOLERANCESFRACTION DIM =DECIMAL DIM .XX =DECIMAL DIM .XXX =ANGULAR DIM =XUAREVISED TITLETR11/19/2019 REVDESCRIPTIONBYDATEADJUSTABLE FLANGE (OPTION 14)BAYONET CAP and SPRING (OPTION 13A)SPEC :J. PERRYPYROMATION, 53 TITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 DWG. NO. & SHEET NO:B2815014/29/2011 This document is PROPRIETARY toPyromation, #: RBF185L483-005-13A03-4 TOLERANCESFRACTION DIM =DECIMAL DIM.

8 XX =DECIMAL DIM .XXX =ANGULAR DIM =AX1 5/8"AREVISED TITLETR11/19/2019 REVDESCRIPTIONBYDATESPEC :J. PERRYPYROMATION, 53 TITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 DWG. NO. & SHEET NO:B2814014/29/2011 This document is PROPRIETARY toPyromation, #: RBF185L483-006-303-4 TOLERANCESFRACTION DIM =DECIMAL DIM .XX =DECIMAL DIM .XXX =ANGULAR DIM =COLD LEGA90 BEND1/2" R (1/8", 3/16", 1/4" )1" R (3/8" )HOT LEGBREVISED TITLETR11/19/2019 ACHANGED ARROW HEAD SIZE & CHANGED OD TO One-time Adjustable Compression FittingsCODETYPENPTSIZE(inches)PRESSURER ATEDAVAILABLESHEATHDIAMETERS(inches)05A3 16 stainless steel1/8 YES1/8, 3/16, 1/405B316 stainless steel1/4 YES1/8, 3/16, 1/4, 3/805C316 stainless steel1/2 YES1/8, 3/16,1/4, 3/815 ABrass1/8NO1/8, 3/16, 1/415 BBrass1/4NO3/16, 1/4, 3/815 CBrass1/2NO1/4, 3/8 SPEC :J.

9 PERRYPYROMATION, 53 TITLE:SIZE:DRAWN BY:AFOR:FORT WAYNE, INDIANA 260-484-2580 DWG. NO. & SHEET NO:B2816014/29/2011 This document is PROPRIETARY toPyromation, #: RBF185L483-006-14-4 TOLERANCESFRACTION DIM =DECIMAL DIM .XX =DECIMAL DIM .XXX =ANGULAR DIM =XAREVISED TITLETR11/19/2019 REVDESCRIPTIONBYDATEP hone (260) 484-2580 FAX (260) 482-6805 or (800) 837-6805 Code RT02 Sheath TerminationsConfiguration Code RT01 Leadwire Transitions54-11 RTD-3RT02 ORDER CODES RT013-1 Plug and Jack Sheath TerminationsCODEDESCRIPTION4 Standard plug5 Standard jack6[1]Miniature plug7[1]Miniature jack OptionsMCMating connectorCL[2]Compression L bracket to hold plug to sheath[1] Not available with 1/4" or 3/8" sheath[2] Not available with miniature connector3-2 Leadwire transitions (Requires Table 4 and 5 selections)

10 CODEDESCRIPTION13[1]Same size transition with heat-shrink tubing 104 C [220 F]15 extension leadwire transition with relief spring 204 C [400 F]16 extension leadwire transition with heat-shrink tubing 104 C [220 F]18[1]Same size transition without heat-shrink tubing 204 C [400 F]19 extension leadwire transition without spring or heat-shrink tubing 204 C [400 F] OptionsHT[2]High temperature potting 538 C [1000 F]not available with option 13 or 16[1] Not available with flex armor[2] Not available with option 13 or 16. When specifying high temp potting with Flex Armor option 19 must be Order Number:---or4,MC3-1 R5T185L483-006-00 PAGERTD-4-163-2 R5T185L483-006-01A,304 PAGERTD-53-2 Threaded Fittings with extension Leadwire (Requires Table 4 and 5 selections)CODEDESCRIPTION6HN231/2" x 1/2" NPT steel hex nipple8HN231/2" x 1/2" NPT stainless steel hex nipple9HP231/2" NPT stainless steel bushing (no process threads)8 RNDC233/4" process x 1/2" NPT stainless steel hex nippleSPEC :J.