Example: dental hygienist
Regulators Series AR
Note 1) The AR10 type comes with a backflow function as a standard feature. (K is not available.) When using the AR10 type as w/ backflow function, backflow may not occur with the set pressure 0.15 MPa or less. For AR20K to 60K, please set the inlet pressure to at least 0.05 MPa higher than the set pressure. Note 2) to the new Measurement Law.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Nylon Tubing Series T/TIA - SMC ETech
content2.smcetech.comModel Fluid Air 0.6MPa at 20°C Refer to burst pressure characteristics curve. –20 to +60°C (No freezing) Polyurethane Max. operating pressure Burst pressure
IP8m Series Electro-Pneumatic Positioner/Smart …
content2.smcetech.comSmart Positioner Built-in microcomputer and sensor allows easy remote parameter change and monitoring. Display example Input value (%) Full Output Functions Handles 2-line Input for Current Equipment
Multiplicador de presión / Depósito de aireNuevo
content2.smcetech.comTubo del cilindro Guía de tirante Modelo de accionamiento neumático Presión máx. de trabajo 1.6 MPa Modelo de presión multiplicada por 4 Multiplicador de presión Serie VBA
ISO Interface Solenoid Valve/SIZEq Metal Seal …
content2.smcetech.com1.19-8 Series VS7-6 Sub-plate Sub-plate: Series VS7-1/VSA7-1 Side piping Applicable solenoid valve/air operated valve Sub-plate size Piping ∗ Weight Series ISO size q
5/2-, 5/3-, 2x3/2-Wege-Elektromagnetventil Serie …
content2.smcetech.com2 Steigern Sie die Leistung und Betriebssicherheit Ihrer Maschine mit der neuen Generation von Magnetventilen und Mehrfachanschlussplatten von SMC
Montaggio a fascetta Montaggio su guida
content2.smcetech.comSensori magnetici per cilindri ed attuatori Montaggio a fascetta Montaggio su guida Montaggio su scanalatura Montaggio su tirante Guida alla selezione
One-touch Fittings Series KQ2 - SMC ETech
content2.smcetech.com2 One-touch IN/OUT connection. Possible to use in vacuum to –100KPa. Applications for metric size tube Applicable tube material Nylon, soft nylon, polyurethane
P0893-0946-ITV-CS3e - SMC ETech
content2.smcetech.comElectro-Pneumatic Regulator Electronic Vacuum Regulator Series Model Set pressure range Port size Page ITV001 ITV003 ITV005 0.001 to 0.1 MPa 0.001 to 0.5 MPa 0.001 to 0.9 MPa
Speed Controller with One-touch Fittings Series AS
content2.smcetech.com3 How to Order AS 1F2 2 1 01 06 S Body size M3, M5 standard 1/8, 1/4 standard 3/8 standard 1/2 standard 1 2 3 4 Style Elbow Universal 2 3 Control With One-touch fittings
KQB2 cat en - content2.smcetech.com
content2.smcetech.comVariations Series KQB2 Male Connector KQB2H Metric R thread G thread Inch P. 3 P. 16 P. 10 Bulkhead Union KQB2E Metric Inch P. …
Related documents
Installation Instructions - Watts
media.wattswater.combackflow assembly. 2. Watts Series 957, 957RPDA and LF957RPDA may be in-stalled in either horizontal, “N” pattern, or “Z” pattern position as long as the backflow assembly is installed in accordance with the direction of the flow arrow on the assembly and the local water authority approves the installation. 3.
Sample Exam Questions and Recommended References …
www.abccert.orgC. Pressure vacuum breaker assembly D. Reduced pressure backflow assembly 9. While testing check valve #2 of a reduced pressure backflow assembly under backpressure, what would be observed if the second check valve was fouled? A. No differential on the test kit and no discharge from the relief valve B.
CROSS CONNECTION RULES MANUAL - Michigan
www.michigan.govAppendix E - Backflow Assembly Test Procedures . Appendix F - Sample Letters . Appendix G - Approved Backflow Preventers (iii) 1 Chapter 1 - INTRODUCTION . A cross connection is a connection or arrangement of piping or appurtenances through which backflow of nonpotable water could flow into the public drinking water
RP/IS-009 Installation, Maintenance, & Repair Series 009 ...
media.wattswater.comvalves or a backflow assembly have been operated. Certified tes-ters of backflow assemblies must conduct this confirming test. Figure 4 Relief Valve Discharge Rates 1⁄2" – 1" (15-25mm) 009 45 40 35 30 20 15 10 5 0 0 1020 3040 50 60 7080 90100 150 zone pressure psi Flow Rate gpm 1⁄2" 3⁄4" M2 X 1" M2 11⁄4" – 3" (32-80mm) 009 350 300 ...
MISSOURI DEPARTMENT OF NATURAL RESOURCES WATER …
dnr.mo.govbackflow prevention assembly test data and maintenance report . customer customer number file number mailing address service location meter number date of test time a.m. p.m. supply pressure lbs. air gap (2 x supply diam.) pass supply in. gap in. fail type of assembly …
Series 009 - Watts
media.wattswater.comA Reduced Pressure Zone Assembly shall be installed at each potential health hazard location to prevent backflow due to backsiphonage and/or backpressure. The assembly shall consist of an internal pressure differential relief valve located in a zone between two positive seating check modules with captured springs and silicone seat discs.
BACKFLOW PREVENTION ASSEMBLY FIELD TEST FORM
fccchr.usc.edubackflow prevention assembly field test form: mainline bypass: mainline bypass: created date: 1/3/2018 1:32:57 pm ...
Price List - Watts
media.wattswater.comKit consists of: spring assembly, disc and bracket, bolt O-rings and cover O-ring. SS07F Repair Kits Check Kits 0888940 RK SS07F CK 4" 682.50 0888941 RK SS07F CK 6" 857.00 0888942 RK SS07F CK 8", 10" 985.50 Kit consists of: complete check assembly.
CHAPTER 6 WATER SUPPLY AND DISTRIBUTION
www.ecodes.bizd. All secondarysubmetersand backflow assemblies shall be at least the same size as the line in which they are installed. e. Table based on minimum water main pressure of 50 psi. SECTION 604 DESIGN OF BUILDING WATER DISTRIBUTION SYSTEM 604.1 General. The design of the water distribution system shall conform to accepted engineering practice ...
Product Manual for Northstar HOT WATER/STEAM PRESSURE …
www.northerntool.comgallons per minute. The use of a backflow preventer on the water supply hose is recommended and may be required by local code. Any cleaning chemicals that are used must be specifically approved for use in pressure washers. The pump is powered by a gasoline-fueled engine. The spray water is heated (when desired) by a kerosene/fuel-