Quad Voltage
Found 10 free book(s)
Low-power quad voltage comparator - STMicroelectronics
www.st.comLow-power quad voltage comparator Features Wide single supply voltage range or dual supplies for all devices: +2 V to +36 V or ±1 V to ±18 V Very low supply current (1.1 mA) independent of supply voltage (1.4 mW/comparator at +5 V) Low input bias current: 25 nA typ. Low input offset current: ±5 nA typ.
LMV331 - Single, Dual, Quad General Purpose, Low Voltage ...
www.onsemi.comSingle, Dual, Quad General Purpose, Low Voltage Comparators The LMV331 is a CMOS single channel, general purpose, low voltage comparator. The LMV393 and LMV339 are dual and quad channel versions, respectively. The LMV331/393/339 are specified for 2.7 V to 5 V performance, have excellent input common−mode
LMV321 - Single, Dual, Quad Low-Voltage, Rail-to-Rail ...
www.onsemi.comSingle, Dual, Quad Low-Voltage, Rail-to-Rail Operational Amplifiers LMV321, NCV321, LMV358, LMV324 The LMV321, LMV321I, NCV321, LMV358/LMV358I and LMV324 are CMOS single, dual, and quad low voltage operational amplifiers with rail−to−rail output swing. These amplifiers are a cost−effective solution for applications where low power consumption
SIPROTEC Compact 7SJ80 Multifunction ... - Quad Industry
www.quad-industry.comvoltage transformers is not available in the feeder, the phase-to-ground voltages can be measured directly through a set of capacitor cones in the medium-voltage switchgear. In this case, the functions directional over-current protection (ANSI 67/67N), voltage protection (ANSI 27/59) and frequency protection (ANSI 81O/U) are available.
MCP4728 - 12-Bit, Quad Digital-to-Analog Converter with ...
ww1.microchip.comAug 04, 2010 · • Programmable Voltage and Current Source • Industrial Process Control • Instrumentation • Bias Voltage Adjustment for Power Amplifiers Description The MCP4728 device is a quad, 12-bit voltage output Digital-to-Analog Convertor (DAC) with nonvolatile memory (EEPROM). Its on-board precision output
DM74LS00 Quad 2-Input NAND Gate
ecelabs.njit.eduVCC Supply Voltage 4.75 5 5.25 V VIH HIGH Level Input Voltage 2 V VIL LOW Level Input Voltage 0.8 V IOH HIGH Level Output Current −0.4 mA IOL LOW Level Output Current 8 mA TA Free Air Operating Temperature 0 70 °C Symbol Parameter Conditions Min Typ Max Units (Note 2) VI Input Clamp Voltage VCC = Min, II = −18 mA −1.5 V VOH HIGH Level ...
Low Noise, Precision, Rail-to-Rail Output, JFET Single ...
www.analog.comvoltage, current noise, offset voltage, input bias current, and rail -to-rail output. The ADA4610-1 is a single amplifier , the ADA4610-2 is a dual amplifier, and the ADA4610-4 is a quad amplifier. The combination of low offset, noise, and very low input bias current makes these amplifiers especially suitable for high
LT1366/LT1367/LT1368/LT1369 - Dual and Quad Precision …
www.analog.comDual and Quad Precision ... Input offset voltage is typically 150µV, with an open-loop gain AVOL of 1 million while driving a 10k load. Common mode rejection is typically 90dB over the full rail-to-rail input range, and supply rejection is 110dB. The …
Optocoupler, Phototransistor Output, AC Input, Single ...
www.vishay.comchannel (4 pin) TCMT1600 or quad channel (16 pin) TCMT4600. FEATURES • Low profile package (half pitch) • AC isolation test voltage 3750 VRMS • Low coupling capacitance of typical 0.3 pF • Low temperature coefficient of CTR • Wide ambient temperature range • Material categorization: for definitions of compliance
4 x 50 W MOSFET quad bridge power amplifier
www.st.comSeptember 2013 Rev 6 1/18 1 TDA7850 4 x 50 W MOSFET quad bridge power amplifier Features High output power capability: 4 W–40/ 5 x max. 4 W–40/ 3 x @ 14.4 V, 1 kHz, 10 %