Spice model for
Found 14 free book(s)
A SPICE MODEL FOR IGBTs - Intusoft
www.intusoft.com.MODEL DLIM D (IS=100N).ENDS the turn-off tail time. The OFF control parameter can be added to aid DC convergence by starting DC calculations with Q1 turned off. MOSFET M1 emulates the input MOSFET [3, 4]. The Berkeley SPICE Level=3 model is used in the .MODEL MFIN statement in order to better model modern device characteristics.
BSIM3v3.3 MOSFET Model - Ngspice, the open source Spice ...
ngspice.sourceforge.net4.4 Charge-Thickness Capacitance Model 4-14 4.5 Extrinsic Capacitance 4-19 4.5.1 Fringing Capacitance4-19 4.5.2 Overlap Capacitance4-19 CHAPTER 5: Non-Quasi Static Model 5-1 5.1 Background Information 5-1 5.2 The NQS Model 5-1 5.3 Model Formulation 5-2 5.3.1 SPICE sub-circuit for NQS model5-3 5.3.2 Relaxation time5-4
NGSPICE: Circuit Simulator
web.engr.oregonstate.edu-download ng-spice-rework-26.tar.gz to a working area.-gunzip ng-spice-rework-26.tar.gz-tar xvf ng-spice-rework-26.tar-Go into the newly created ngspice directory and type: ... Control lines tell the simulator which model & run parameters to perform, such as transient analysis or plot. Oregon State University 6. Ngspice User Guide - ECE 391
SIMetrix / SIMPLIS: PSpice model import - Application note
www.st.com1 ESDCAN04-2BWY model import on SIMetrix / SIMPLIS SIMetrix / SIMPLIS provide a procedure to import external spice model. Same procedure has been performed to import ESDCAN04-2BWY PSpice model, using the SIMetrix / …
Automotive SPICE® Process Reference Model
www.automotivespice.comThe Automotive SPICE® PRM is used in conjunction with the Automotive SPICE® Process Assessment Model (PAM) when performing an assessment. The Automotive SPICE® PAM provides additional indicators of process performance and process capability tailored to the needs of performing assessments of software process capability of automotive suppliers.
Automotive SPICE
www.automotivespice.comThis document is a revision of the Automotive SPICE process assessment model 2.5 and the process reference model 4.5, which has been developed under the Automotive SPICE initiative by consensus of the car manufacturers within the Automotive Special Interest Group (SIG), a joint
Solving Convergence Problems - Intusoft
www.intusoft.com• Make sure that there are no unrealistic model parameters; especially if you have manually entered the model into the netlist. • Make sure that all resistors have a value. In SPICE 3, resistors without values are given a default value of 1 kOhm. •Negative capacitor and inductor values are allowed in SPICE 3.
Chapter 8 Using the .DC Statement - University of Washington
class.ece.uw.eduMODEL specifies the optimization reference name used in the ... (SPICE style). However, if parameter sweep, a .DATA statement, and temperature sweep are selected, a parameter name must be chosen for the source value and subsequently referred to in the .DC statement. The parameter name can not start with
Release 9.2, 31 May 2000 Copyright © 1985-2000 Cadence ...
www.seas.upenn.eduEvery part listed has a corresponding PSpice model. The listings are categorized into the following groups: Analog Digital Mixed Signal General devices General devices General devices Japanese devices TTL devices European devices Device Type Generic Name Part Name Part Library Mfg. Name Tech Type The type of device (transistor, diode, etc.).
Spice model tutorial for Power MOSFETs
www.st.comSpice model tutorial for Power MOSFETs Introduction This document describes ST’s Spice model versions available for Power MOSFETs. This is a guide designed to support user choosing the best model for his goals. In fact, it explains the features of different model versions both in terms of static and dynamic characteristics
ngspice user manual
ngspice.sourceforge.netNgspice User’s Manual Version 36 plus (ngspice development version) Holger Vogt, Marcel Hendrix, Paolo Nenzi, Dietmar Warning January 14, 2022
Beginner’s Guide to LTSpice - University of Toronto
www.eecg.utoronto.caon how to create one with a spice command. First, create two inductors L1 and L2 to be the two windings. Press ‘T’ to get the “enter text” dialog and check the “SPICE Directive” box. In the box, type in K1 L1 L2 k, where k is the coefficient of coupling. Normally use ‘1’ for k in case of a toroid or power transformer.
SPICE ‘Quick’ Reference Sheet THE GENERAL ANATOMY OF A ...
web.stanford.eduSPICE Quick Reference Sheet v1.0 THE GENERAL ANATOMY OF A SPICE DECK SPICE input file, called source file, consists of three parts. First, Data Statements describe the components and the interconnections. Then, Control Statements tell SPICE what type of analysis to perform on the circuit. Finally, Output Statements specify what
Orcad Capture User's Guide
www.seas.upenn.eduOrcad® Capture User’s Guide capug.book Page 1 Tuesday, May 23, 2000 12:08 PM