Transmitter Rev
Found 9 free book(s)Model 266HSH Gauge pressure transmitter low power ...
library.e.abb.com8 266HSH GAUGE PRESSURE TRANSMITTERS DS/266HSH/LOWP-EN REV. D — Configuration Transmitter with HART communication Standard configuration transmitters are factory calibrated to customer's specified range. calibrated range and tag number are stamped on the tag plate. if a calibration range and tag
Technical data MTL surge protection EPS 01-107 Rev V …
www.mtl-inst.comtransmitter they are protecting. A bond is required from the general mass of steelwork to the sensor or transmitter housing either using a flat short braid or a cable of at least 4mm2 cross sectional area. In most instances this bond is automatically made by fixing the metallic transmitter housing to the plant structure.
4–20 mA Transmitter AD694 - Analog Devices
www.analog.comThe AD694 is a monolithic current transmitter that accepts high level signal inputs to drive a standard 4–20 mA current loop for the control of valves, actuators, and other devices com-monly used in process control. The input signal is buffered by an input amplifier that can be used to scale the input signal or
Lightning and surge protection - basic principles
www.mtl-inst.comThe field transmitter is pole-mounted away from the control building but con-nected to the telemetry electronics by signal cabling. Most transmitters incorporate some level of isolation from structural earth, typically 500V. This level of isolation now has to withstand the transient voltage between the new
LTC6820 (Rev. C) - Analog Devices
www.analog.comVA Transmitter Pulse Amplitude VA = |VIP – VIM| VDD < 3.3V VDD l≥ 3.3V l VDD – 1.7V 1.6 V V VICMP Threshold-Setting Voltage on ICMP Pin VTCMP = ATCMP • VICMP l 0.2 1.5 V ILEAK(ICMP) Leakage Current on ICMP Pin VICMP = l0V to VDD ±1 µA ILEAK(IP/IM) Leakage Current on IP and IM Pins IDLE State, VIP = VIM = l0V to VDD ±2 µA
Manual: Rosemount OCX 8800 Oxygen and Combustibles …
www.emerson.com00809-0400-4881, Rev AA July 2018 OCX 8800 PREFACE The purpose of this manual is to provide a comprehensive understanding of the OCX 8800 components, functions, installation, andmaintenance. We recommend that you thoroughly familiarize yourself with the Introduction and Installation sections before installing your transmitter.
1. General description - NXP
www.nxp.comRev. 3.6 — 28 November 2017 115436 8 of 222 NXP Semiconductors PN532/C1 Near Field Communication (NFC) controller 7.2 Pin description Table 3. PN532 Pin description Symbol Pin Type Ref Voltage Description DVSS 1 PWR Digital ground. LOADMOD 2 O DVDD Load modulation signal. TVSS1 3 PWR Transmitter ground.
A-Law and mu-Law Companding Implementations Using the ...
www.ti.comAt the telephone transmitter, human speech is converted to analog signals. For digital transmission, this analog signal is converted to a digital signal, which has a fixed precision. To ... A-Law and mu-Law Companding Implementations Using the TMS320C54x (Rev. A ...
SC16IS752; SC16IS762 Dual UART with I2C-bus/SPI interface ...
www.nxp.comProduct data sheet Rev. 9 — 22 March 2012 2 of 60 NXP Semiconductors SC16IS752; SC16IS762 Dual UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR RS-485 driver direction control inversion Built-in IrDA encoder and decoder supporting IrDA SIR with speeds up to 115.2 kbit/s SC16IS762 supports IrDA SIR with speeds up to 1.152 Mbit/s1