Search results with tag "Ansi z21"
Packaged Rooftop Air Conditioners - Trane
www.trane.comexchangers is 10,000 cycles by ANSI Z21.47. This is the standard required by both UL and AGA for cycle test requirements. Trane requires the design to be tested to 2½ times this current standard. The drum and tube design has been tested and passed over 150,000 cycles which is over 15 times the current ANSI cycling requirements.
INSTALLATION INSTRUCTIONS - Lennox
www.lennox.comG40UH(X) units are CSA International certified to ANSI Z21.47 and CSA 2.3 standards. In the USA, installation of gas furnaces must conform with lo-cal building codes. In the absence of local codes, units must be installed according to the current National Fuel Gas Code (ANSI-Z223.1). The National Fuel Gas Code is available from the following ...
INSTALLATION & SERVICE MANUAL - Lochinvar
www.lochinvar.comfor Hot Water Supply Systems, ANSI Z21.22 and the Standard CAN1-4.4 Temperature, Pressure, Temperature and Pressure Relief Valves and Vacuum Relief Valves. The combination temperature and pressure relief valve must be marked with a maximum set pressure not to exceed the maximum working pressure of the water heater. The combination
Installation Manual L2 - Valor Fireplaces
www.valorfireplaces.comThis appliance is certifi ed to ANSI Z21.88/CSA 2.33 American National Standard / CSA Standard for Vented Gas Fireplace Heaters for use in Canada and USA, and to CGA 2.17-91 High Altitude Standard in Canada. This appliance is for direct vent installations. This appliance complies with CSA P.4.1-15 Testing
DRYER VENTING SPECIFICATIONS - Whirlpool
www.whirlpool.com(reference ANSI Z21.5.1 standard). These standards require testing at the maximum-rated exhaust vent conditions that are published in the product literature for each individual model. The designation for the UL or CSA listing can be found on or adjacent to …
Upflow/ Horizontal Left/Right, Downflow Single and 2–Stage ...
www.trane.com(b) Central Furnace heating designs are certified to ANSI Z21.47 / CSA 2.3 — latest edition. (c) Based on U.S. government standard tests. (d) Refer to the Installer's Guide. (e) The above wiring specifications are in accordance withNational Electrical Code; however, installations must comply local codes. MODEL S8X1B060M3PSAA S8X1B060M4PSAA ...
Venting. Reinvented UL 1738 Fuel Gas Venting Systems
iccsafe.orgAppliance Standards –ANSI Z21. Paradox of Rules? IPEX | Certified Flue Gas Venting Solutions 7/26/2019 18 NFPA 54 OEMs ASTM IFGC Standards IMC UL 1738. Model Codes and Standards – There is a clear disconnect between appliance manufacture’s, vent manufacturer’s and
325 Series Line Pressure Regulators C US
igate.northernplumbing.comCSA: ANSI Z21.80/CAN 6.22 Maximum Inlet Pressure Model CSA Certified 325-3(B)L 325-5(B)L 2 psi (13.8 kPa) 325-7A(B)L ... NOTE: All Max itrol line pressure regulators must be installed and operated in accordance with Maxitrol’s Safety Warning Instructions. Figure 4: Pressure Drop Chart 325-3 L L
Installation Manual
downloads.hearthnhome.comSTANDARD: ANSI Z21.97-2017, CSA 2.41-2017 A. Appliance Certification D. Noncombustible Materials Specification Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof. Materials that are reported as passing ASTM E 136,
ANSI Z223.1 National Fuel Gas Code
ahmad-tomasz.weebly.com(1) American National Standard Installation of Gas Appliances and Gas Piping, ANSI Z21.30 (NFPA 54) (2) Installation of Gas Piping and Gas Equipment on Industrial Premises and Certain Other Premises, ANSI Z83.1 (NFPA 54A) (3) Fuel Gas Piping, ASME B31.2 The first edition of the code was issued in 1974. It combined the requirements of the three