2013 Edition FlangEd Fittings

1 2013 Edition FlangEd FittingsductilE ironindustrial applications, watEr & wastEwatEr30"-64"NSF Certified toANSI/NSF 61 FlangEd FittingsNSF Certified toANSI/NSF 61p 2866. dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101table of contentsFlanged Fittings for Water 3 Flange Details 5 FlangEd Fittings 6 90 and 45 Bend 6 22-1/2 and 11-1/4 Bends 7 Tees 8 Crosses 11 90 Base Bends 14 Base Tees 15 Base Drilling Details for Base Bends and Tees 18 Concentric Reducers 19 Eccentric Reducers 21 90 Long Radius Bends 23 Reducing Bends 90 24 Blind Flanges 25 Wye Branches 26 True Wyes 27 Straight Flare 28 Flange and Flare 90 Bends (Standard and Long Radius) 29 Method of Designating Outlets of Reducing Fittings in Specifications 30 Method of Designating Location of Tapped Holes When Specified 31 Combination of Standard Fittings That May be Used in Place of Special Fittings 32 Products for Water, Waste Water and Fire Protection 33 Note.

2 If specifiers and users believe that corrosive soils will be encountered where our products are to be installed, please refer to ANSI/AWWA C105 Polyethelene Encasement for Ductile Iron Pipe Systems for proper external protection FittingsNSF Certified toANSI/NSF 61p 3866. dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101 FlangEd Fittings for water and other liquids ANSI/AWWA C110 Ductile-Iron and Gray-Iron Fittings . For Water (3-through 48" sizes).ANSI/AWWA C153 Ductile-Iron Compact Fittings , For Water Service (54" through 64" sizes). Pipe s FlangEd Fittings are produced of Ductile Iron and conform to the applicable requirements for Ductile Iron Fittings specified in ANSI/AWWA C110 C104 Cement-Mortar Lining for Ductile-Iron and Gray-Iron Fittings for system options include primer base coat and cement-mortar lining with asphaltic coating A536 "Standard Specification for Ductile Iron Castings."ansi/ awwa standardsFlanged Fittings are typical components in rigid piping systems.

3 Such systems are particularly suited for above ground installation: water filtration plants, sewage disposal plants, wastewater treatment plants, pumping stations and industrial plants. Our Special Projects Department has the knowledge and experience to assist with the unique design challenges of plant systemsUnless otherwise specified, FlangEd Fittings will be furnished with a standard thickness cement-mortar lining with asphaltic coating inside and outside. Fittings are furnished coated or uncoated in accordance with the purchasers requirements. The underground use of the FlangEd joint is generally not recommended due to the rigidity of the joint. Unequal settlement or other stressing of such piping may result in excessive strain on the flanges or the FittingsNSF Certified toANSI/NSF 61p 4866. dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101accessoriesThe gaskets and bolts to be used with FlangEd pipe and Fittings should be selected by the purchaser with due consideration for the particular service and installation requirements.

4 FlangEd joint accessories (bolts, nuts and gaskets) can be furnished by Pipe if so specified. Pipe's FULL FACE FLANGE-TYTE Gaskets or RING FLANGE-TYTE Gaskets (4" through 64"size) are recommended for all FlangEd compatibility and pressure ratingsThe flanges of ANSI/AWWA C110 and C153 standards conform to the drilling and facing of ANSI Class 125 flanges. This Class 125 designation leads some to conclude that these AWWA flanges are only rated at 125 psi service which is not correct. ANSI/AWWA C110 FlangEd Fittings are rated for 350 psi operating pressure for 3" through 12" sizes, 250 psi operating pressure for 14" through 48" sizes and ANSI/AWWA C153 Fittings are rated for 150 psi operating pressure for 54" through 64" sizes. These ratings are at ambient temperatures with at least a 2:1 factor of safety. Special gaskets such as Pipe s FULL FACE FLANGE-TYTE Gaskets or RING FLANGE-TYTE Gaskets are required for operating pressures greater than 250 psi.

5 (Flanges of Ductile Iron Fittings meeting the requirements of ANSI/AWWA C110 cannot be joined with Class 250 ANSI flanges.)special service requirementsWhen requesting prices for FlangEd piping other than water service, please furnish complete information regarding the type of material to be conveyed, composition, concentration, pH, pressure and Fittings for water and other liquids (cont.)Note: Pipe recommends the use of FULL FACE FLANGE-TYTE Gaskets or RING FLANGE-TYTE Gaskets with Ductile Iron FlangEd joint products supplied by Pipe. These gaskets were designed specifically for the unique surface of Ductile Iron. Flat rubber gaskets are NOT considered equal in performance and may not provide the sealing capability the project requires. In addition, their use could result in unintended damage to the flanges and threads of the fabricated pipe by applying excess torque to the bolts/flanges in order to seal the FittingsNSF Certified toANSI/NSF 61p 5866.

6 Dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101 DIMeNSIoNS Inches SIze BoLt HoLe BoLt Qty. oF Inches oD BC t Diameter Diameter & Length BoLtS 3 .75 .12 3/4 5/8 x 2-1/2 4 4 .94 .12 3/4 5/8 x 3 8 6 .12 7/8 3/4 x 3-1/2 8 8 .12 7/8 3/4 x 3-1/2 8 10 .12 1 7/8 x 4 12 12 .12 1 7/8 x 4 12 14 .19 1-1/8 1 x 4-1/2 12 16 .19 1-1/8 1 x 4-1/2 16 18 .19 1-1/4 1-1/8 x 5 16 20 .19 1-1/4 1-1/8 x 5 20 24 .19 1-3/8 1-1/4 x 5-1/2 20 30 .25 1-3/8 1-1/4 x 6-1/2 28 36 .25 1-5/8 1-1/2 x 7 32 42 .25 1-5/8 1-1/2 x 7-1/2 36 48 .25 1-5/8 1-1/2 x 8 44 54 .25 2 1-3/4 x 8-1/2 44 60 .25 2 1-3/4 x 9 52 64 .25 2 1-3/4 x 9 52 LAyING LeNGtH DIMeNSIoNS: Pipe face-to-face dimensions conform to a tolerance of.

7 12" for sizes 3"-64" Fittings face-to-face dimensions conform to a tolerance of .06" for sizes 3"-10" and .12" for sizes 12"-64". The largest opening governs the tolerance for all openings. Center-to-face tolerances are one half the face-to-face : The bolt circle and bolt holes of these flanges match those of ANSI/AWWA C115 and Class 125 flanges shown in ANSI and can be joined with and Class 125 flanges. The flanges do not match the Class 250 flanges shown in ANSI and cannot be joined with Class 250 FlangEd Fittings and valves. For technical information on Class 250 flanges see Pipe's Class 250 Flanges submittal document at : Class 125 flanges are plain faced without projection and are furnished smooth or with shallow : Complies with ANSI/AWWA C115 FlangEd Ductile Iron Fittings - Flange detailsFlanged FittingsNSF Certified toANSI/NSF 61p 6866. dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101 Note.

8 Actual weights of Fittings , sizes 54"-64", may exceed those flange details see page 30"-48" conform to ANSI/AWWA C110 Sizes 54"-64" conform to ANSI/AWWA C153 DIMeNSIoNS WeIGHt PReSSuRe Inches Pounds SIze RAtING 90 45 90 45 Inches psi t A R A R 30 250 1430 1120 36 250 2380 1966 42 250 3271 3138 48 250

9 4755 3580 54 150 6085 4344 60 150 7705 5493 64 150 9197 6635 FlangEd Fittings - 90 and 45 BendsFlanged FittingsNSF Certified toANSI/NSF 61p 7866. dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101 Note: Actual weights of Fittings , sizes 54"-64", may exceed those flange details see page 30"-48" conform to ANSI/AWWA C110 Sizes 54"-64" conform to ANSI/AWWA C153 DIMeNSIoNS WeIGHt PReSSuRe Inches Pounds SIze RAtING 22-1/2 11-1/4 22-1/2 11-1/4 Inches psi t A R A R 30 250 1135 1150 36 250 1790 1805 42 250 2665

10 2680 48 250 3665 3695 54 150 3502 3217 60 150 3966 3467 64 150 4987 4379 FlangEd Fittings - 22-1/2 and 11-1/4 BendsFlanged FittingsNSF Certified toANSI/NSF 61p 8866. dip . pipE 2013 EditionREVISED PiPE And FoUndRY Co. FlangEd di Fittings BRo-101 Note: Actual weights of Fittings , sizes 54"-64", may exceed those Fittings - tees SIze PReSSuRe RAtING DIMeNSIoNS WeIGHt Inches psi Inches Pounds RuN BRANCH t t1 H J tee 30 06 250.