24 Flush Mount DeFlector Vent: sKMD24F0As

1 E 1 CNHEFDABJ L IM KG Note: the face of the shelf must sit 1 3/4" ( mm) back from the face of the faceshelf faceO24" Flush Mount DeFlector Vent: sKMD24F0As installation INSTRUCTIONS1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, viewAAnti-Tip blockMounting cleatBCDrawer faceCabinetfaceNote: the mounting surface of the finished cleat must sit 1 1/16" ( mm) backfrom the face of the cabinet [pushing the face of the drawer out 1/4" ( mm)].Figure 1 Figure 2 AImportant notes to the Installer Read all of the installation Manual that is included with the Microwave Drawer before installing in the Flush Mount configuration. Observe all governing codes, ordinances, and safety instructions . Be sure to leave these instructions with the includes:Q t number1PR EF-B019M R P 0 Flush Mount DeFlector Vent2LX-CZB055 MRE0 Mounting screws TINSEB541 MRR2A.

2 6" ( mm)B. Suggested electrical outlet locationC. Anti-Tip blockD. 5" (127 mm)E. 3-1/2" ( mm)F. 4" ( mm)G. 24-3/16" ( mm) minimum 24-1/2" ( mm) maximumH. 14-13/16" ( mm) to bottom of Anti-Tip blockI. 1-1/16" ( mm)J. 23-1/2" ( mm) minimum depthK. 22-1/8" ( mm) L. 1-3/4" ( mm) M. 16-7/8" ( mm) openingN. Floor must support 100 lb ( kg)O. 1-3/4" ( mm)A. 22" ( mm) mounting cleat opening widthB. 1/4" ( mm)C. 1-1/16" ( mm)E 2 Shelf detail showing the DeFlector vent detail showing the DeFlector vent during DeFlector vent and mark holes. Pre drill using a 1/16" ( mm) bit before viewNo oven BASuggested electrical outlet location Anti-Tip block3/4" ( mm)shelfSide view1 3/4" ( mm)front face of shelfFront face of cabinet 16 7/8"( mm) Flush opening heightMove oven locationdownward for extended countertops for better viewing angle.

3 Anti-Tipblock3. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical Carefully guide the drawer into the prepared opening. Avoid contact with the sides of the cutout opening and also pinching the cord between the oven and the Slide the drawer all the way back until the mounting flanges touch the cleats mounted in the cabinet Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16 ( mm) bit. See Figure 3 AFigure 4 Figure 3B2. Install DeFlector as shown in Figure Secure the drawer with the 4 screws 2 BFigure 2CA. 22-1/8" ( mm) mounting cleat opening widthB. 24-3/16" ( mm) minimum 24-1/2" ( mm) maximum Flush opening widthC. 3/4" ( mm) shelfE 3C NH EFDBAJL I cabinet faceshelf faceO G KM Note: the face of the shelf must sit 1 3/4" ( mm) back from the face of the " Flush Mount DeFlector Vent: sKMD30F0As installation INSTRUCTION1.

4 Prepare cabinet opening as shown in Figures 1, 2A, 2B, viewABCAnti-Tip blockMounting cleatDr awer faceCabinetfaceNote: the mounting surface of the finished cleat must sit 1 1/16" ( mm) backfrom the face of the cabinet [pushing the face of the drawer out 1/4" ( mm)].Figure 1 Figure 2 AImportant notes to the Installer Read all of the installation Manual that is included with the Microwave Drawer before installing in the Flush Mount configuration. Observe all governing codes, ordinances, and safety instructions . Be sure to leave these instructions with the includes:Q t number1 PREF-B020 MRP0 Flush Mount DeFlector Vent2LX-CZB055 MRE0 Mounting screwsA. 6" ( mm)B. Suggested electrical outlet locationC. Anti-Tip blockD. 5" (127 mm)E. 3-1/2" ( mm)F.

5 4" ( mm)G. 30-5/16" ( mm) minimum 30-5/8" ( mm) maximumH. 14-13/16" ( mm) to bottom of Anti-Tip blockI. 1-1/16" ( mm)J. 23-1/2" ( mm) minimum depthK. 28-7/16" ( mm) L. 1-3/4" ( mm) M. 16-7/8" ( mm) openingN. Floor must support 100 lb ( kg)O. 1-3/4" ( mm)A. 28-1/2" ( mm) mounting cleat opening widthB. 1/4" ( mm)C. 1-1/16" ( mm)E 4 Shelf detail showing the DeFlector shield detail showing the DeFlector vent during DeFlector vent and mark holes. Pre drill using a 1/16" ( mm) bit before viewNo oven CBAS uggested electrical outlet location Anti-Tip block1 Sharp Plaza Suite 1, Mahwah, New Jersey 07495-1123, USA 1-800-BE-SHARP (237-4277)335 Britannia Road East, Mississauga, Ontario, L4Z 1W9, Canada3. Place the drawer adjacent to the wall or cabinet opening.

6 Plug the power supply cord into the electrical Carefully guide the drawer into the prepared opening. Avoid contact with the sides of the cutout opening and also pinching the cord between the oven and the Slide the drawer all the way back until the mounting flanges touch the cleats mounted in the cabinet Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16 ( mm) bit. See Figure 3 AFigure 4 Figure 3B2. Install DeFlector as shown in Figure Secure the drawer with the 4 screws 2 BFigure 2C3/4" ( mm)shelfSide view1 3/4" ( mm)front face of shelfFront face of cabinet 16 7/8"( mm) Flush opening heightMove oven locationdownward for extended countertops for better viewing angle. Anti-TipblockA. 28-7/16" ( mm) mounting cleat opening widthB.

7 30-5/16" ( mm) minimum 30-5/8" ( mm) maximum Flush opening widthC. 3/4" ( mm) shelf