256 360NF Data Sheet) - Tremco

1 09/08. 2 Pages Vulkem 360NF PRODUCT. data . sheet . RAPID CURE LOW ODOUR/LOW WATERPROOFING BASECOAT. USAGE/PURPOSE. Vulkem 360NF . For odour sensitive applications adjacent to KEY BENEFITS SUMMARY occupied areas: Plazas Rapid cure Stadiums Balconies Ideal for odour sensitive applications Mechanical Rooms Tenacious adhesion Pool/Recreation Decks Bonds to most substrates (Primerless) Retention Tanks Can be applied at various thicknesses to correct irregular surfaces PACK SIZE PRODUCT CODE. 19L pail 215436. COLOUR. PRODUCT information White DESCRIPTION. Vulkem 360NF is a low odour, low water cured, rapid setting polyurethane basecoat that possesses TECHNICAL information . tenacious adhesion to clean and dry concrete, wood and metal.

2 Vulkem 360NF is a versatile basecoat that can TYPICAL PHYSICAL PROPERTIES. be applied at various thicknesses. PROPERTY TEST METHOD VULKEM 360NF . Vulkem 360NF has been specially formulated for odour Tensile strength ASTM D412 2 MPa sensitive applications in heavily occupied areas. Vulkem . % Elongation ASTM D412 500%. 360NF is ideal for plaza areas, pool and recreational 100% Modulus ASTM D412 decks, balcony terraces, mechanical rooms, stadiums, Hardness, Shore A ASTM C661 40-50. ramp areas and retention tanks. Vulkem 360NF is ideal Tear Strength ASTM D6642 for restoration work where both time and odour are a Cure time@ 25 C ASTM D1640 4 hrs max concern. VOC 95 g/L. Vulkem 360NF forms a seamless, monolithic PRECAUTIONS.

3 Waterproofing membrane capable of bridging a Do not apply to damp or contaminated surfaces crack without compromising the waterproof integrity of Use with adequate ventilation the system. Tremco offers a range of compatible Vulkem topcoats that form a strong interlaminate bond to the Vulkem . 360NF . Compatible topcoats are Vulkem 351/351NF. and Vulkem 951NF. These topcoats when used in conjunction with the recommended aggregate, create a tough, aesthetically pleasing, abrasion resistant, wearing surface over the Vulkem 360NF basecoat. Vulkem 360NF . USAGE GUIDELINES. METHOD OF APPLICATION GUARANTEE/WARRANTY. Concrete shall be water cured and in place for at least Tremco products are manufactured to rigid standards 14 days, preferably 28 days.

4 Any type of broom finish is of quality. Any product which has been applied (a) in acceptable. New or existing slabs must be clean, sound accordance with Tremco written instructions and (b) in and free of all contaminants which may interfere with any application recommended by Tremco , but which is adhesion or proper curing. Excessive moisture on proved to be defective, will be replaced free of charge. concrete surface may compromise adhesion and cure properties. Chemical and/or mechanical surface Any information provided by Tremco in this document preparation may also be required. in relation to Tremco 's goods or their use is given in good faith and is believed by Tremco to be Structural or shrinkage cracks in concrete greater than appropriate and reliable.

5 However, the information is shall be ground out to a minimum of 6mm wide x provided as a guide only, as the actual use and 12mm deep. application will vary with application conditions which are beyond our control. Tremco makes no representation, Water is added at a rate of one part water to five parts guarantee or warranty relating to the accuracy or Vulkem 360NF basecoat. Mix until water is completely reliability of the information and assumes no obligation incorporated into base polymer, resulting in a viscous, or liability in connection with the information . To the elastomeric coating. extent permitted by law, all warranties, expressed or implied are excluded. Vulkem 360NF basecoat is normally applied at the rate of yielding approximately thickness.

6 The coating is squeegee applied followed by back rolling to evenly distribute the material. Allow Vulkem 360NF to cure a minimum of 6 hours and a maximum of 24 hours at 25 C and 50%RH. NOTE: The Vulkem 360NF should have a slightly tacky surface to aid in the adhesion of the Vulkem Ultra High Solids Topcoat. For details of application of topcoats see separate data sheet . HEALTH & SAFETY PRECAUTIONS. The Material Safety data sheet (MSDS) and container label must be read and understood prior to use. TECHNICAL SERVICE. Tremco has a team of qualified Technical Sales Representatives who provide assistance in the selection and specification of products. For more detailed information or service and advice, call Customer Service on (02) 9638 2755 or fax (02) 9638.

7 2955. Tremco PTY LTD ABN 25 000 024 064. Unit 1, 2 Park Rd, RYDALMERE NSW 2116 Australia Tel (02) 9638 2755 Fax (02) 9638 2955. An Company