4.5” Suspension System

1 Suspension SystemJeep Wrangler JK | 2007-2014 Rev. 081414491 W. Garfield Ave., Coldwater, MI 49036 . Phone: 517-279-2135 Web/live chat: . E-mail: PART #0144462 | 014446 Read And Understand All Instructions And Warnings Prior To Installation Of System And Operation Of YOUR SAFETYC ertain BDS Suspension products are intended to improve off-road performance. For your safety and the safety of your passengers, take the following precautions. HANDLING - Modified vehicles will likely handle differently than a factory equipped vehicle.

2 ROLLOVERS - Extreme care must be used to prevent loss of control or vehicle rollover. DRIVE SAFELY - If you do fail to drive your modified vehicle safely, it may result in serious injury or death. DON T MIX SYSTEMS - We do not recommend the combined use of Suspension lifts, body lifts, or other lifting devices. STAY SOBER - You should never operate your modified vehicle under the influence of alcohol or drugs. OBEY THE LAW - Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions.

3 Always wear your seat PROFESSIONAL INSTALLATION - BDS Suspension recommends that this System be installed by a professional technician. PROFESSIONAL KNOWLEDGE - Disassembly/reassembly procedures and post installation checks must be known to install this System . SPECIAL LITERATURE REQUIRED - OE Service Manual for model/year of vehicle. Refer to manual for proper disassembly/reassembly procedures of OE and related components. OE RECOMMENDATIONS - Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the OE manual.

4 LARGER RIM AND TIRE COMBINATIONS - These may increase leverage on Suspension , steering, and related components. When selecting combinations larger than OE, consider the additional stress you could be inducing on the OE and related components. DRIVE LINE VIBRATION - After installation vehicles may experience drive line vibrations. Angles may require tuning, slider on shaft may require replacement, shafts may need to be lengthened or trued, and U-joints may need to be replaced. SHOP SAFETY - Secure and properly block vehicle prior to installation of components.

5 Always wear safety glasses when using power tools. WITH A HOIST - If installation is to be performed without a hoist, we recommend rear alterations first. AMOUNT OF LIFT - Due to payload options and initial ride height variances, the amount of lift is a base figure. Final ride height dimensions may vary in accordance to original vehicle attitude. Always measure the attitude prior to beginning THE INSTALLATION, BEFORE YOU DRIVE Check all fasteners for proper torque. Check to ensure for adequate clearance between all rotating, mobile, fixed, and heated members.

6 Verify clearance between exhaust and brake lines, fuel lines, fuel tank, floor boards and wiring harness. Check steering gear for clearance. Test and inspect brake System . Perform steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating, mobile or heated members. Inspect rear brake hoses at full extension for adequate slack. Failure to perform hose check/ replacement may result in component failure. Longer replacement hoses, if needed can be purchased from a local parts supplier.

7 Perform head light check and adjustment. Re-torque all fasteners after 500 miles. Always inspect fasteners and components during routine APPLICABLE TO ALL BDS Suspension SYSTEMS014446 | 3014446 Box KitFRONT track BAR RELOCATION BRACKET01964B1 Front track Bar x .083 x Sleeve01393B1 Support Bracket5621 Bolt Pack27/16"-14 x 1" bolt37/16" SAE washer27/16"-14 prev. torque nut19/16"-12 x 3" bolt29/16 SAE washer19/16 -12 prev. torque nut11/2"-13 square nut11/2"-13 x 1" bolt11/2" SAE washer6451 Bolt Pack19/16"-12 x 3-1/2" bolt29/16" SAE washer19/16"-12 prev.

8 Torque nut23/8"-16 x 1-1/4" bolt43/8" SAE washer23/8"-16 prev. torque nut014446 Box KitPart #QtyDescription084402R1 Dropped Pitman ArmW96S4 Trans. Skid Spacer WasherA1872 Rear Adjustable Flex UCAF ront and Rear Bump Stops339623in x 3in Front Extension4381 Front Bump Stop Bolt Pack13/8"-16 x 1-1/4" self-tapping bolt23/8" USS washer23/8"-16 x 3-1/2" bolt7631 Rear Bump Stop Bolt Pack25/16"-18 x 1-1/4" bolt25/16"-18 x 7/8" bolt45/16"-18 prev. torque nut 85/16" SAE washer01928B2 Rear Bump Stop ExtensionREAR SWAY BAR LINKS920252 Sway Bar ExtensionSB58BK45/8 ID Hourglass x.

9 075 x Sleeve7581 Bolt x 60mm prev. torque nut41/2" SAE washer#1425H - 4 Lift Kit Shown with Optional Adjustable Lower Control Arms4 | 014446124310 Box Kit (Non-Rubicon)Part #QtyDescriptionA1682 Front Disconnect Assembly013022 Disconnect x .120 x Sleeve9121 Bolt Pack21/2"-13 x 3" bolt grade 521/2"-13 prevailing torque nut81/2" SAE flat washer21/2"-20 prevailing torque nut21-3/8" OD x 1/2" ID x 3/16" Lanyard124320 Box Kit (Rubicon)Part #QtyDescription9111102 Fixed Front Sway Bar x .120 x SleeveSB34BK43/4 ID Hourglass BushingB12X3G521/2 x 13 x 3 BoltN12PT21/2 x 13 Prevailing Torque NutW12S41/2in Washer124314 Box Kit (2012+ Only)Part #QtyDescription018391 Exhaust Extension - Extension - Pass8141 Bolt Pack28mm x 70mm bolt28mm x 60mm bolt45/16" SAE washer124339 Box KitPart #QtyDescriptionA1822 Rear LCA w/ rubber bushings2 Door Coil SpringsPart #QtyDescription0343112 Front Coil Springs - taller (2 door)0343192 Rear Coil Springs (2 door)

10 4 Door Coil SpringsPart #QtyDescription0344112 Front Coil Springs - taller (4 door)0344192 Rear Coil Springs (4 door)124331 Box KitPart #QtyDescriptionA1812 Front LCA w/ rubber bushings014446 Box KitREAR track BAR RELOCATION01967B1 Rear track Bar Bracket x .090 x Sleeve5631 Bolt Pack19/16"-12 x 3" bolt29/16" SAE washer19/16"-12 prev. torque nut13/8"-16 x 1-1/4" bolt23/8" SAE washer13/8"-16 prev. torque nutBRAKE LINE RELOCATION017162 Front Brake Line Nylon Cable TieJKBL-D1 Rear Brakelline Brkt - DrvJKBL-P1 Rear Brakeline Brkt - Pass7041 Bolt Pack - Front Brake Lines21/4"-20 prev.