Example: bankruptcy
8051 Instruction Set - Silicon Labs
family specific header files. For example, the F930 SFRs are in the “C8051F930_defs.h” header file. As you can see from this chart the number of SFRs has grown significantly over the original 8051. The SFRs are used as the configuration registers for peripherals within the device as well as control functions for the core.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
AN986: BLUETOOTH® A2DP AND AVRCP PROFILES
www.silabs.comSilicon Labs TABLE OF CONTENTS 1 Introduction 4 1.1 Advanced Audio Distribution Profile 4 1.2 Audio/video Remote Control Profile 5 2 iWRAP firmware overview 6
Frequency Modulation FM Tutorial - Silicon Labs
www.silabs.comFrequency Modulation (FM) Tutorial Lawrence Der, Ph.D. Silicon Laboratories Inc. Introduction Edwin H. Armstrong, known as one of the founding fathers of radio technology, invented the
C8051F310/1/2/3/4/5/6/7 - Silicon Labs
www.silabs.comC8051F310/1/2/3/4/5/6/7 Rev. 1.8 3 Table Of Contents 1. System Overview..... 17
Isolated RS232 and RS485 Expansion Board User Guide
www.silabs.comIsolated RS232 and RS485 Expansion Board User Guide The Silicon Labs Isolated RS232 and RS485 Evaluation Board is a hardware plugin card for EFM8 and EFM32 Starter Kits (STKs).
C8051F040/1/2/3/4/5/6/7 - Silicon Labs
www.silabs.comC8051F040/1/2/3/4/5/6/7 Rev. 1.6 3 Table of Contents 1. System Overview..... 19
A Stroke of Genius for Smart TVs: Add Voice to Your Remote ...
www.silabs.comA Stroke of Genius for Smart TVs: Add Voice to Your Remote Control Introduction In this age of the Internet of Things (IoT), connected devices are getting smarter and smarter. We have smart phones, smart homes, smart cars, smart appliances, and even ... digitize our voice and send it over the Internet where it is processed for a response. The
DESIGN OF PRINTED TRACE DIFFERENTIAL OOP NTENNAS 1 ...
www.silabs.comalso provides a general tutorial on how to design a differential loop antenna, using a combination of design ... 2.1. Design Characteristics of Loop Antennas The following represents a brief list of some of the characteristics of loop antennas; each of these items is
High-Performance, Single-Chip …
www.silabs.comThe Si4629 supports worldwide analog AM and FM radio reception and incorporates a fully integrated decoder for the European Radio Data System (RDS) and the North
AN1107: Si5332 Power Supply Noise Rejection - Silicon Labs
www.silabs.comAN1107: Si5332 Power Supply Noise Rejection This application note showcases the power supply noise rejection (PSNR) performance of Si5332. Power supply noise are a significant problem in high performance clocking. A clock cir-cuit that is dependent on a voltage source will be affected by the noise of that source in the following ways:
Enhancing Power Supply Rejection Ratio for Low-Jitter Clocks
www.silabs.comEnhancing Power Supply Rejection Ratio for Low-Jitter Clocks . Today's electronic systems require advanced design from top to bottom. Cost and ... especially in high-power systems. Ripple as high as 100 mVp-p is common in some networking and computing applications.
Related documents
UM1722 User manual - STMicroelectronics
www.st.comExamples and applications using the FreeRTOS™ can ... Various header files provided by silicon manufacturers and tool vendors that define processor specific memory addresses and utility macros. ... Various peripheral driver source files and binaries provided by silicon
ATmega16A - Microchip Technology
ww1.microchip.com5. About Code Examples This documentation contains simple code examples that briefly show how to use various parts of the device. These code examples assume that the part specific header file is included before compilation. Be aware that not all C Compiler vendors include bit definitions in the header files and interrupt handling in C is compiler
nRF5 Series: Developing with SEGGER Embedded Studio
infocenter.nordicsemi.com3.In the folder where you extracted the nRF5 SDK, navigate to examples\peripheral\blinky \hex. 4.Select the HEX file that corresponds to your development board and copy it to the JLINK drive. The development board will now restart and run the application. If the LEDs on the board start blinking, you have successfully programmed your first ...