Active Filter Design Techniques - George Washington …

1 Chapter 16 Active Filter Design TechniquesLiterature Number SLOA088 Excerpted fromOp Amps for EveryoneLiterature Number: SLOD006A16-1 Active Filter Design TechniquesThomas IntroductionWhat is a Filter ?A Filter is a device that passes electric signals at certain frequencies orfrequency ranges while preventing the passage of others. circuits are used in a wide variety of applications. In the field of telecommunication,band-pass filters are used in the audio frequency range (0 kHz to 20 kHz) for modemsand speech processing. High-frequency band-pass filters (several hundred MHz) areused for channel selection in telephone central offices.

2 Data acquisition systems usuallyrequire anti-aliasing low-pass filters as well as low-pass noise filters in their preceding sig-nal conditioning stages. System power supplies often use band-rejection filters to sup-press the 60-Hz line frequency and high frequency addition, there are filters that do not Filter any frequencies of a complex input signal, butjust add a linear phase shift to each frequency component, thus contributing to a constanttime delay. These are called all-pass high frequencies (> 1 MHz), all of these filters usually consist of passive componentssuch as inductors (L), resistors (R), and capacitors (C).

3 They are then called LRC the lower frequency range (1 Hz to 1 MHz), however, the inductor value becomes verylarge and the inductor itself gets quite bulky, making economical production these cases, Active filters become important. Active filters are circuits that use an op-erational amplifier (op amp) as the Active device in combination with some resistors andcapacitors to provide an LRC-like Filter performance at low frequencies (Figure 16 1).LRCVINVOUTVINVOUTR1C1C2R2 Figure 16 1. Second-Order Passive Low-Pass and Second-Order Active Low-PassChapter 16 Fundamentals of Low-Pass Filters 16-2 This chapter covers Active filters.

4 It introduces the three main Filter optimizations (Butter-worth, Tschebyscheff, and Bessel), followed by five sections describing the most commonactive Filter applications: low-pass, high-pass, band-pass, band-rejection, and all-pass fil-ters. Rather than resembling just another Filter book, the individual Filter sections are writ-ten in a cookbook style, thus avoiding tedious mathematical derivations. Each sectionstarts with the general transfer function of a Filter , followed by the Design equations to cal-culate the individual circuit components. The chapter closes with a section on practicaldesign hints for single-supply Filter Fundamentals of Low-Pass FiltersThe most simple low-pass Filter is the passive RC low-pass network shown in Figure 16 16 2.

5 First-Order Passive RC Low-PassIts transfer function is:A(s)+1 RCs)1RC+11)sRCwhere the complex frequency variable, s = j + , allows for any time variable signals. Forpure sine waves, the damping constant, , becomes zero and s = j .For a normalized presentation of the transfer function, s is referred to the Filter s cornerfrequency, or 3 dB frequency, C, and has these relationships:s+swC+jwwC+jffC+jWWith the corner frequency of the low-pass in Figure 16 2 being fC = 1/2 RC, s becomess = sRC and the transfer function A(s) results in:A(s)+11)sThe magnitude of the gain response is:|A|+11)W2 For frequencies >> 1, the rolloff is 20 dB/decade.

6 For a steeper rolloff, n Filter stagescan be connected in series as shown in Figure 16 3. To avoid loading effects, op amps,operating as impedance converters, separate the individual Filter of Low-Pass Filters16-3 Active Filter Design TechniquesRCRCRCRCVINVOUTF igure 16 3. Fourth-Order Passive RC Low-Pass with Decoupling AmplifiersThe resulting transfer function is:A(s)+1 1)a1s 1)a2s AAA(1)ans)In the case that all filters have the same cut-off frequency, fC, the coefficients becomea1+a2+AAAan+a+2n *1 , and fC of each partial Filter is 1/ times higher than fCof the overall 16 4 shows the results of a fourth-order RC low-pass Filter .

7 The rolloff of each par-tial Filter (Curve 1) is 20 dB/decade, increasing the roll-off of the overall Filter (Curve 2)to 80 : Filter response graphs plot gain versus the normalized frequency axis ( = f/fC).Fundamentals of Low-Pass Filters 16-4 40 50 60 20 100100 30 70 Frequency Ideal 4th Order Lowpass4th Order Lowpass1st Order Lowpass|A| Gain dB 180 270 900100 Frequency Ideal 4thOrder Lowpass4th Order Lowpass1st Order Lowpass Phase degreesNote:Curve 1: 1st-order partial low-pass Filter , Curve 2: 4th-order overall low-pass Filter , Curve 3: Ideal 4th-order low-pass filterFigure 16 and Phase Responses of a Fourth-Order Passive RC Low-Pass FilterThe corner frequency of the overall Filter is reduced by a factor of times versus the 3 dB frequency of partial Filter of Low-Pass Filters16-5 Active Filter Design TechniquesIn addition, Figure 16 4 shows the transfer function of an ideal fourth-order low-pass func-tion (Curve 3).

8 In comparison to the ideal low-pass, the RC low-pass lacks in the following characteris-tics:DThe passband gain varies long before the corner frequency, fC, thus amplifying theupper passband frequencies less than the lower transition from the passband into the stopband is not sharp, but happensgradually, moving the actual 80-dB roll off by octaves above phase response is not linear, thus increasing the amount of signal gain and phase response of a low-pass Filter can be optimized to satisfy one of thefollowing three criteria:1) A maximum passband flatness,2) An immediate passband-to-stopband transition,3) A linear phase that purpose, the transfer function must allow for complex poles and needs to be ofthe following type:A(s)+A0 1)a1s)b1s2 1)a2s)b2s2 AAA 1)ans)bns2 +A0Pi 1)ais)bis2 where A0 is the passband gain at dc, and ai and bi are the Filter the denominator is a product of quadratic terms, the transfer function representsa series of cascaded second-order low-pass stages, with ai and bi being positive real coef-ficients.

9 These coefficients define the complex pole locations for each second-order filterstage, thus determining the behavior of its transfer following three types of predetermined Filter coefficients are available listed in tableformat in Section :DThe Butterworth coefficients, optimizing the passband for maximum flatnessDThe Tschebyscheff coefficients, sharpening the transition from passband into thestopbandDThe Bessel coefficients, linearizing the phase response up to fCThe transfer function of a passive RC Filter does not allow further optimization, due to thelack of complex poles.

10 The only possibility to produce conjugate complex poles using pas-Fundamentals of Low-Pass Filters 16-6sive components is the application of LRC filters. However, these filters are mainly usedat high frequencies. In the lower frequency range (< 10 MHz) the inductor values becomevery large and the Filter becomes uneconomical to manufacture. In these cases Active fil-ters are filters are RC networks that include an Active device, such as an operational ampli-fier (op amp).Section shows that the products of the RC values and the corner frequency mustyield the predetermined Filter coefficients ai and bi, to generate the desired transfer following paragraphs introduce the most commonly used Filter Butterworth Low-Pass FIltersThe Butterworth low-pass Filter provides maximum passband flatness.