ATI 316Ti™
ATI 316Ti stainless is a titanium-stabilized version of Type 316 molybdenum-bearing austenitic stainless steel. It is also known as DIN/EN designation No. 1.4571. The Type 316 alloys offer excellent resistance to general corrosion and pitting/crevice corrosion, which is better than the conventional chromium-nickel austenitic stainless steels ...
Tags:
Steel, Stainless, Stainless steel
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
EUROPE MIDDLE EAST AL 29-4C Alloy - atimetals.com
www.atimetals.comA Superferritic Stainless Steel for ... (Grade 2) at room ... Similar to other high chromium ferritic stainless steels, AL 29-4C alloy has demonstrated excellent ...
Grade, Steel, Stainless, Stainless steel, Alloys, Al 29 4c alloy
Technical Data Sheet - ATI Relentless Innovation®
www.atimetals.comthe first major use of JS700 stainless steel, ... superaustenitic stainless grade have been reported in other difficult applications, ...
Technical Data Sheet - atimetals.com
www.atimetals.comATI A286™ alloy content is similar in chromium, nickel, and molybdenum to some of the austenitic stainless steels. Consequently, ATI A286™ alloy possesses a level of aqueous corrosion resistance comparable to that of the austenitic
ATI Ti-6Al-4V, Grade 5
www.atimetals.comATI Ti-6Al-4V, Grade 5 Titanium Alloy (UNS R56400) INTRODUCTION. ATI Ti-6Al-4V, Grade 5 alloy (UNS R56400) is the most widely used titanium grade. It is a two phase α+β titanium alloy, with aluminum as the alpha stabilizer and vanadium as the beta stabilizer. This high-strength alloy can be used at cryogenic
(UNS N08367) - atimetals.com
www.atimetals.comChemical Element Typical AL-6XN® Alloy Typical AL-6XN Plus® Alloy UNS N08367 C Type 316 27 -3 Alloy 825 27 -3 Type 317 36 2 Alloy 904L 59 15 Alloy 2205 68 20
Technical Data Sheet
www.atimetals.comoffers optimized in-reactor corrosion resistance by adjusting the alloy aim point within the ASTM specification ranges. Controlled Composition Zircaloy-4 has lower tin (1.3%) and higher iron (0.22%) than the standard grade. Zr-2.5Nb (Grade R60904) is a binary alloy with niobium to increase the strength. The alloy has been
AL 29-4C For Heating and Ventilating
www.atimetals.comSilicon Chromium Nickel Molybdenum . Nitrogen 0.02: Titanium+Columbium (Niobium) Iron Balance. 0.02 0.50 . 0.03 <0.01 . ... By using AL 29-4C heat exchangers, furnace manufacturers have benefited by being able to offer extended warranties in ... tool coatings such as titanium nitride have been helpful in extending tool life. Contact your ...
Related documents
Roughness measurements of stainless steel surfaces
www.worldstainless.orgRoughness measurements of stainless steel surfaces Introduction Ra value Surface roughness is a measure of the texture of a surface. It is ... Plate, Sheet, and Strip [11] EN 10088-2, Stainless steels – Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steel for general purposes
Duplex Stainless Steel 2205 ( UNS S31803/S32205)
super-metals.comDuplex stainless steel 2205 alloy offers extensive resistance to the local corrosion factors like intergranular, pitting and crevice corrosion. The CPT of duplex stainless steel 2205 alloy is minimum 35oC. It offers outstanding resistance to the chloride ion stress cracking at temperature ranges to 150oC.
Stainless Steel Grade Datasheets
www.akamparsco.comaustenitic stainless steel. It can be supplied with a tensile strength of up to over 1300 MPa in strip and wire forms, to produce tempers in the range of 1/16 Hard to Full Hard. The controlled analysis of Grade 301 enables it to retain sufficient ductility in conditions up to 1/2 Hard conditions to be roll or brake formed into
Stainless 302, 304, 304L, 305 - upmet.com
www.upmet.comMinimum mechanical properties for annealed Types 302, 304, 304L, and 305 austenitic stainless steel plate, sheet and strip as required by ASTM specifications A 240 and ASME specification SA-240 are shown below.
Color Code Chart - EMJ
www.emjmetals.comSTRIP, AND EXTRUSIONS Commercial Quality 1144 HI Stress and StressprooP 'Fatigue-ProoP Stainless Bar 303S ANN 303SCOND B 303Se ANN 303% COND B 304 ÅNN 3041 ANN 316 ANN 321 ANN Alloy Bar 4130 As Rolled 4130 Heat Treated 4140 Q + T RT 4140/42/45 ANN 4140/42/45 HT ASTM A434 GR BC and BD ASTM GR B7 347 ANN ZIOANN 410 …
Stainless Steel 310/310S (UNS S31000/ UNS S31008)
super-metals.comWelding of Stainless Steel 310S Stainless steel grade 310/310S are welded through similar electrodes and filler metals. These are readily weldable through SMAW, GMAW, GTAW and SAW. The preferred electrodes are AWS A5.4 E310-XX and A 5.22 E310T-X and filler metal is AWS A5.9 ER310. Argon is used as a shielding gas.