Axial piston variable pump (A)A10VSO Series 31

1 RE-A 92711 , Bosch Rexroth AGFeatures variable pump with Axial piston rotary group in swash-plate design for hydrostatic drives in open circuit. The flow is proportional to the drive speed and displace-ment. The flow can be infinitely varied by adjusting the swash-plate angle. 2 drain ports Excellent suction performance Low noise level Long service life Favorable power/weight ratio Versatile controller range Short control time The through drive is suitable for adding gear pumps and Axial piston pumps up to the same size, , 100% through drive. Suitable for operation with mineral oil and HF hydraulic fluids All-purpose medium pressure pump Sizes 18 to 140 Nominal pressure 4100 psi (280 bar) Maximum pressure 5100 psi (350 bar) Open circuitAxial piston variable pump(A)A10 VSO Series 31 AmericasRE-A 92711 Edition.

2 Code 2 Hydraulic fluids 4 Working pressure range 6 Technical data, standard unit 7 Technical data, high-speed version 8 Technical data, HF hydraulic fluids, maximum rotational speed 9DG Two-point control, direct operated 12DR Pressure controller 13 DRG Pressure controller, remote controlled 14 DFR/DFR1 Pressure flow controller 15 DFLR Pressure, flow and power control 17ED Electrohydraulic pressure control 18ER Electrohydraulic pressure control 19 Dimensions, size 18 to 140 20 Dimensions, through drive 38 Overview of mounting options 42 Combination pumps (A)A10 VSO + (A)A10 VSO 43 Connector for solenoids 44 Installation instructions 45 Project planning notes 48 Safety instructions 48 Bosch Rexroth AG, RE-A 92711 Series 31 | Axial piston variable pumpType codeType code01020304050607080910111213A10 VSO/31 VVersion1828457188100 14001 Standard version (without code) HFA, HFB, HFC hydraulic fluid (except for Skydrol) EHigh-speed version (external dimensions are not affected by this option).

3 HAxial piston unit02 Swashplate design, variable , nominal pressure 4100 psi (280 bar), maximum pressure A10VS5100 psi (350 bar) AA10 VSOperating mode03 Pump, open circuitOSize (NG)04 Geometric displacement , (see table of values on pages 6 and 7)1828457188 100 140 Control device05 Two-point control, direct operated DGPressure controllerhydraulic DRwith flow controllerhydraulicX-T open DFRX-T plugged with flushing function DFR1X-T plugged without flushing function DRSC with pressure cut-offhydraulicremote controlled DRGelectricalnegative controlU = 12 V ED71U = 24 V ED72electricalpositive controlU = 12 V ER71U = 24 V ER72 Pressure,flow and power controller DFLRS eries06 Series 3, index 131 Direction of rotation07 Viewed on drive shaftclockwiseRcounter-clockwiseLSealing material08 FKM (fluoroelastomer)VNBR (nitrile rubber) only if using HFA, HFB and HFC hydraulic fluids (position 01.)

4 Order code E )PDrive shaft09 Splined shaft ANSI shaft Ssimilar to shaft S however for higher input torque Rreduced diameter, not for through drive UParallel keyed shaft ISO 3019-1permissible through-drive torque (see page 10) KMounting flange1828457188100 14010 ISO 3019-12-hole C4-hole DWorking port11 SAE flange port UNC fastening threadat side, opposite 62 92 RE-A 92711 , Bosch Rexroth AG Axial piston variable pump | A10 VSO Series 31 Type code 3 Through drive (for mounting options, see page 42)12 Flange ISO 3019-1 Hub for splined shaft1)DiameterDiameter1828457188 100 140without through drive N0082-2 (A)5/8 in9T 16/32DP K013/4 in11T 16/32DP K52101-2 (B)7/8 in13T 16/32DP K681 in15T 16/32DP K04127-2 (C)1 1/4 in 14T 12/24DP K071 1/2 in 17T 12/24DP K24152-4 (D)1 3/4 in 13T 8/16DP K17 Connectors for solenoids2)13 Without connector (without solenoid, with hydraulic control only, without code) HIRSCHMANN connector without suppressor diode H = Available = On request = Not availableNotice Note the project planning notes on page 48.

5 In addition to the type code, please specify the relevant technical data when placing your V1) Hub for splined shaft according to ANSI ) Connectors for other electric components can Rexroth AG, RE-A 92711 Series 31 | Axial piston variable pumpHydraulic fluidsHydraulic fluidsThe (A)A10 VSO variable pump is designed for operation with HLP mineral oil according to DIN 51524-2. Application instructions and requirements for hydraulic fluids should be taken from the following data sheets before the start project planning: 90220: Hydraulic fluids based on mineral oils and related hydrocarbons 90221: Environmentally acceptable hydraulic fluids 90222: Fire-resistant, water-free hydraulic fluids (HFDR/HFDU) (for permissible technical data, see data sheet 90225) 90223: Fire-resistant, water-containing hydraulic fluids (HFAE, HFAS, HFB, HFC) for version E see also data sheet 90225.

6 90225: Restricted technical data only for operation with fire-resistant, water-free and water-containing hydraulic fluids (HFDR, HFDU, HFA, HFB, HFC)- technical dataNotes on selection of hydraulic fluidThe hydraulic fluid should be selected so that the operating viscosity in the operating temperature range is within the optimum range ( opt see selection diagram).Notice The Axial piston unit is suitable for operation with water-containing HF hydraulic fluid. See version E Viscosity and temperature of hydraulic fluidsViscosityShaft seal Temperature3)CommentCold start max 7400 SUS (1600 mm /s)NBR2) St 40 F ( 40 C) t 3 min, without load (p 725 psi (50 bar)), n 1000 min-1 Permissible temperature difference between Axial piston unit and hydraulic fluid in the system maximum 45 F (25 K) FKM St -13 F (-25 C)Warm-up phase = 7400 to 1850 SUS(1600 to 400 mm /s)t 15 min, p pnom and n nnomContinuous operation = 1850 to 60 SUS(400 to 10 mm /s)1)NBR2) = +185 F (+85 C)measured at port L, L1 FKM = +230 F (+110 C) opt = 170 to 74 SUS(36 to 16 mm /s)Range of optimum operating viscosity and efficiencyShort-term operation min = 60 to 50 SUS(10 to 7 mm /s)NBR2) = +185 F (+85 C)

7 T 3 min, p pnom , measured at port L, L1 FKM = +230 F (+110 C) Selection diagram-40-25-1010305090115700-40-13 1450861221942401583250602003001005001000 2000300046007400VG 22VG 32VG 46VG 68VG 1007417071040602010020040060010001600[SU S][mm2/s][ C][ F]1636 Warm-up phaseMaximum permissible viscosityfor cold startMinimum permissible viscosityfor short-term operationTemperature [ C]Viscosity v ContinuousoperationMinimum permissible viscosity for cold start opt1) Corresponds for VG 46 to a temperature range of + F (+4 C) to +185 F (+85 C) (see selection diagram)2) Version (if operating with HFA, HFB and HFC hydraulic fluids3) If the temperature at extreme operating parameters cannot be adhered to, please contact us. RE-A 92711 , Bosch Rexroth AG Axial piston variable pump | A10 VSO Series 31 Hydraulic fluids 5 Filtration of the hydraulic fluidFiner filtration improves the cleanliness level of the hydraulic fluid, which increases the service life of the Axial piston unit.

8 A cleanliness level of at least 20/18/15 is to be maintained according to ISO very high hydraulic fluid temperatures (maximum 230 F (110 C), measured at port L, L1), at least a cleanliness level of 19/17/14 according to ISO 4406 is contact us if the above classes cannot be Rexroth AG, RE-A 92711 Series 31 | Axial piston variable pumpWorking pressure rangeWorking pressure rangePressure at working port BDefinitionNominal pressure pnom4100 psi (280 bar)The nominal pressure corresponds to the maximum design pressure pmax5100 psi (350 bar)The maximum pressure corresponds to the maximum working pressure within the single operating period. The sum of the single operating periods must not exceed the total operating operating period2 msTotal operating period300 hMinimum pressure pB abs (high-pressure side)145 psi (10 bar)1)Minimum pressure on the high-pressure side (B) which is required in order to prevent damage to the Axial piston unit.

9 Rate of pressure change RA max232060 psi/s(16000 bar/s)Maximum permissible speed of pressure build-up and reduction during a pres-sure change across the entire pressure at suction port S (inlet)Minimum pressure pS minStandard12 psi ( bar)absoluteMinimum pressure at suction port S (inlet) that is required in order to avoid dam-age to the Axial piston unit. The minimum pressure depends on the rotational speed and displacement of the Axial piston pressure pS max145 psi (10 bar)absoluteFor higher inlet pressure, please consult usLeakage pressure at port L, L1 Maximum pressure pL max30 psi (2 bar)absolute1)Maximum psi ( bar) higher than inlet pressure at port S, but not higher than pL max. A case drain line to the reservoir is required. Rate of pressure change RA maxpnom t pTime tPressure p Pressure definitionPressure pt1t2tnSingle operating periodMinimum pressure (high-pressure side)Maximum pressure pmaxNominal pressure pnomTime tTotal operating period = t1 + t2 +.

10 + tnNoticeWorking pressure range valid when using hydraulic fluids based on mineral oils. Please contact us for values for other hydraulic permissible inlet pressure at suction port S with speed increaseIn order to avoid damage to the pump (cavitation), a mini-mum inlet pressure must be guaranteed at suction port S. The minimum inlet pressure level depends on the rotational speed and the displacement of the variable ( )( )( )( )( )( )Rotational speed n/nnomHigh speed versionStandard versionInlet pressure pS abs [psi (bar)] displacement Vg/ Vg maxDuring continuous operation in overspeed over nnom, a reduction in operational service life is to be expected due to cavitation ) Other values on request RE-A 92711 , Bosch Rexroth AG Axial piston variable pump | A10 VSO Series 31 Technical data, standard unit 7 Technical data, standard unitSizeNG1828457188100140 displacement , geometric, per revolutionVg (cm3)(18)(28)(45)(71)(88)(100)(140)Rotat ional speedmaximum1)at Vg maxnnomrpm3300300026002200210020001800at Vg <Vg max2)