Example: tourism industry
Compressor Installation Instructions - Sanden
The aluminum seal seat and O-ring must be clean and not damaged. Torque to 11-15 ft•lb (15-20 N•m, 150-200 kgf•cm). Be careful not to cross thread the oil plug. Proper A/C System Operation and Cleanliness for Warranty Coverage When a compressor fails due to internal failure as evidenced by poor pumping or the shaft locked up or uneven
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Compressor Installation Instructions - Sanden USA
www.sanden.comSanden Compressor Installation Instructions Safety Precautions 1. Be aware that air bags can be deployed accidentally. 2. Smoking or open flames around refrigerant can cause dangerous fumes.
FLX - Sanden
www.sanden.comModel Configuration List Model No. Clutch Description Clutch Voltage Sealed Heavy Duty Oil Type Body Mount Type 4860 A2, 125mm 12 volt No SP-15 PAG Ear Mount
Delivering Excellence General Motors A/C …
www.sanden.comThe Sanden Advantage Sanden is a premier innovator and manufacturer of compressors for mobile HVAC applications. Sanden has been …
SD Service Guide Sept 08 - Sanden USA
www.sanden.com4 1.0 Compressor Models Covered Type R-134a R-12 SD7B10 SDB-706 7 Cylinder SD7H13 SD-708 SD7H15/ HD, SHD SD-709 SD7B10 / SD5H09 SD-505 SD5H11 SD-507
1. Check Bubbles in Sight Glass Refrigerant …
www.sanden.com6. Check air gap of clutch. closed. % lace valve. S. Check heater water valve. Evaporator Condenser S ction Hose Discharge H 7. Leak test and diagnose
SD Service Guide Sept 08 - Sanden USA
www.sanden.com2 Table of Contents 1. Compressor Models Covered 2. Compressor Nomenclature 3. Cautionary Information 3.1 Pressure Release 3.2 Recovery of Refrigerant
1. Check Bubbles in Sight Glass Refrigerant …
www.sanden.com6. Check air gap of clutch. closed. % lace valve. S. Check heater water valve. Evaporator Condenser S ction Hose Discharge H 7. Leak test and diagnose
Sanden International (USA), Inc
www.sanden.comALL NEW OEM COMPRESSORS • Sanden International (USA), Inc. began marketing automotive air conditioning compressors in 1974 and has been manufacturing compressors in the U.S. since
Fit n Drive AC EDGE - Sanden USA
www.sanden.comAC EDGE AC EDGE is a new corporate brand housed under Sanden Corporation, which has over 30 years of automotive air-conditioning expertise and is an established OE (Original Equipment) supplier
1. CHEMICAL PRODUCT AND COMPANY …
www.sanden.comMATERIAL SAFETY DATA SHEET Trade Name: SANDEN SP-10 8.45 oz MSDS NO. 3201-1996 Revision Date: 01/05/2012 Date Printed 01/05/2012 Page 1 of 4 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Related documents
A Practical Guide to Shaft Alignment - Plant Services
www.plantservices.comSeal wear increases due to shaft loading when shafts are misaligned. Pump seals are a high cost item often costing up to a third of the total pump cost. Poor installation and excessive shaft misalignment will substantially reduce seal life. Manufacturers have addressed the problem of poor installation practice by the introduction of cartridge
SKF SPEEDI-SLEEVE new generation
www.skf.comAlthough installation is simple, it should be done carefully to achieve the best results. As the thin-walled sleeve has an interference fit, any disturbances on the shaft surface may create a similar pattern on the sleeve surface and cause the seal to leak. Therefore, the seal counterface surface of the shaft should be
SKF Seal Handbook SKF - Tri-State Bearing
www.tristate-bearing.comInstallation instructions and troubleshooting guidelines are also provided. Simply organized, the illustrative charts and detailed ... shaft seal is a barrier with four functions: 1) Retaining lubricants or liquids 2) Excluding contaminants 3) Separating fluids and 4) Confining pressure.
PARTS & INSTALLATION INSTRUCTIONS E-46 & E-47 …
ww2.meyerproducts.coma) The damaged pump drive Shaft Seal (3) may be removed by careful extraction with a pointed tool. Dip new Seal in oil and with lip down, press into Pump Housing flush to 1/32 inch below face of boss. 4. BASE (24) a) Remove and clean Solenoid (40) and inspect for external damage. b) Test Coil (41) for electrical continuity. Nominal Coil
Selecting Centrifugal Pumps - KSB
www.ksb.com– the mode of installation, which is dealt with in section 7. , – the nominal diameter (for the pump size, as a function of the flow rate), – the rated pressure (for the wall thickness of casings and flanges), – the temperature (for example for the selection of cooling equipment for shaft seals), – the fluid pumped (abrasive,
MP-Series Low-inertia Servo Motor with 100 mm to 165 mm ...
literature.rockwellautomation.comUsing Shaft Seals An additional seal is required on the motor shaft near the motor front bearing if the shaft is exposed to fluids or significant amounts of fine dust. This includes lubricating oil from a gearbox. An IP66 rating for the motor requires the use of a shaft seal and environmentally sealed connectors/cables.
Kinetix TLP Multi-purpose Servo Motors with 046. . . 235 ...
literature.rockwellautomation.comShaft Seals An additional seal is required on the mo tor shaft near the motor front bearing if the shaft is exposed to significant amounts o f fine dust or fluids, such as lubricating oil from a gearbox. An IP65 rating for the motor requires a shaft seal and environmentally sealed connectors and cables.
Installation and Operation Manual - Watts
media.wattswater.comInstallation and Operation Manual Hot Water Recirculation System Model 500800 IOM-WQ-500800 ... Do not mount the motor shaft in a vertical position. NOTICE If desired, Sensor Valve can be mounted to the wall with the ... use pipe dope or Tefl on tape to seal the threads. If a gasketed, fl exible copper water heater connector is used, ...