ELG-100 - Meanwell

1 70~100W Constant Voltage + Constant Current LED Driver C C A Dx IP67IP65 File Name: ELG-100 -SPEC 2020-09-25 ELG-100 series { IS 15885(Part 2/Sec13)R-41027766 THOMAS SAMUELTHOMAS SAMUEL(for 24/24B/36/36A/42/42A/48/48B/54/54A only) / 115 VAC / 230 VAC *63* (L*W*H) ; 16 ~ 34V47 ~ 54V41 ~ 48V54 ~ 62V62 ~ 72V88%90%89%90%91% ELG-100 -24200mVp-p2 ~ 4A12 ~ ~ ~ ~ ~ ~ 2A24 ~ ~ ~ ~ ~ ~ ~ ~ RANGE RANGEPOWER FACTOREFFICIENCY (Typ.)AC CURRENTINPUTINRUSH CURRENT(Typ.)LEAKAGE CURRENTEMC IMMUNITYWORKING TEMP. WORKING HUMIDITYSTORAGE TEMP., HUMIDITYTEMP. COEFFICIENTVIBRATIONMTBFDIMENSIONOTHERSN OTEPACKINGOVER TEMPERATUREOVER VOLTAGE1000ms, 80ms/115 VAC 500ms, 100ms/230 VAC15ms/115 VAC 10ms/230 VAC47 ~ 63Hz< / 277 VACC ompliance to EN55015,EN61000-3-2 Class C (@load 60%); EN61000-3-3;;EAC TP TC 020; KGB17743, KN15,KN6154720 ~ 95% RH non-condensing-40 ~ +80 C, 10 ~ 95% RH C (0 ~ 60 C)10 ~ 500Hz, 5G , period for 72min.}

2 Each along X, Y, Z axesENVIRONMENTEMC EMISSION SAFETY &EMCPROTECTIONShut down output voltage, re-power on to recoverShut down output voltage, re-power on to recoverSHORT CIRCUIT I/P-O/ I/P- O/P- , I/P-FG, O/P-FG:100M Ohms / 500 VDC / 25 C/ 70% RHWITHSTAND VOLTAGEISOLATION RESISTANCETOTAL HARMONIC DISTORTIONDC VOLTAGERATED CURRENT RATED POWER VOLTAGE ADJ. RANGECURRENT ADJ. RANGELINE REGULATION LOAD REGULATION SETUP, RISE TIME UP TIME (Typ.)RIPPLE & NOISE (max.) TOLERANCE CURRENT REGION CURRENT SAFETY STANDARDS Adjustable for A/AB-Type only (via the built-in potentiometer) Adjustable for A/AB-Type only (via the built-in potentiometer) COLD START 60A(twidth=850s measured at 50% Ipeak) at 230 VAC ; Per NEMA 410 MAX. No. of PSUs on 16A CIRCUIT BREAKER3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230 VACMAX.

3 CASE TEMP. Tcase=+90 CUL8750(type HL ), CSA No. ; independent, EN62384; IEC/EN/AS/NZS 61347-1, IEC/EN/AS/NZS 61347-2-13 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV);EAC TP TC 020; KC KN15,KN61547(Please refer to "STATIC CHARACTERISTIC" section)100 ~ 305 VAC 142 ~ 431 VDC continue,320 VAC for 24 Hrs; 360 VAC for 1Hr C C C C Product Liability Disclaimer For detailed information, please refer to ~100W Constant Voltage + Constant Current LED Driver95 ~ 108%Hiccup mode, recovers automatically after fault condition is removedConstant current limiting, recovers automatically after fault condition is removed PF , PF , PF @full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)Tcase=-40 ~ +90 C (Please refer to OUTPUT LOAD vs TEMPERATURE section)No load power consumption < for Blank / A / Dx / D2-TypeNO LOAD / STANDBYPOWER CONSUMPTIONS tandby power consumption < for B / AB / DA-TypeTHD< 20%(@load 50%/115VC; @load 60%/230 VAC; @load 75%/277 VAC)(Please refer to TOTAL HARMONIC DISTORTION(THD) section) hrs min.

4 Telcordia SR-332 (Bellcore) min. MIL-HDBK-217F (25 C)EAC TP TC 004;BIS IS15885(for 24/24B/36/36A/42/42A/48/48B/54/54A only);; IP65 or IP67; , ,KC61347-2-13 approvedELG-100 series70W70W70W70W70W200 VAC ~ 305 VAC100 VAC ~ 180 VACDALI STANDARDSC ompliance to IEC62386-101,102,(207 by request) for DA Type onlyFile Name: ELG-100 -SPEC 2020-09-25 Block DiagramPFC fosc : 50~120 KHzPWM fosc : 60~130 KHz70~100W Constant Voltage + Constant Current LED Driver This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the METHODS OF LED MODULET ypical output current normalized by rated current (%) In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please contact MEAN (min.)Vo(%)50100Io(%)(B)ConstantCurrent area(C)HiccupProtection(A)ConstantVoltag e areaDETECTIONPWM & FILTERRECTIFIERSPOWERSWITCHINGFILTER&REC TIFIERSVo+Vo- This characteristic applies to Blank/A/B/AB/DX/D2-Type, For DA-Type, the Constant Current area is 60%~100% seriesCASE :Protective EarthFile Name: ELG-100 -SPEC 2020-09-25AC/L(Brown)AC/N(Blue)DIMMING OPERATIONELG-100 Applying additive 0 ~ 10 VDC Applying additive 10V PWM signal (frequency range 100Hz ~ 3 KHz): Applying additive resistance:Note : 1.

5 Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0k or 0 Vdc, or 10V PWM signal with 0% duty +Vo-DIM+DIM-+++--- DO NOT connect "DIM- to Vo-"Additive VoltageVo+Vo-DIM+DIM-++-- DO NOT connect "DIM- to Vo-"Additive PWM signalVo+Vo-DIM+DIM-++-- DO NOT connect "DIM- to Vo-"Additive Resistance0V1V2V3V4V5V6V7V8V9V10V10%0%20 %30%40%50%60%70%80%90%100%Output current (%)0%10%20%30%40%50%60%70%80%90%100%10%0 %20%30%40%50%60%70%80%90%100%Output current (%)10%0%20%30%40%50%60%70%80%90%100%Outp ut current (%)Dimming input: Additive voltageDuty cycle of additive 10V PWM signal dimming input70~100W Constant Voltage + Constant Current LED Driver 3 in 1 dimming function (for B/AB-Type) Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10 VDC, or 10V PWM signal or resistance.

6 Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.) * DIM+ for B/AB-Type DA+ for DA-Type PROG+ for D2-Type* *DIM- for B/AB-Type DA- for DA-Type PROG- for D2-TypeShort10K/N20K/N30K/N40K/N50K/N60K /N70K/N80K/N90K/N100K/N(N=driver quantity for synchronized dimming operation)Dimming input: Additive resistanceDIM-(White)**DIM+()*BlueVo+(Re d)Vo-(Black) ELG-100 seriesFile Name: ELG-100 -SPEC 2020-09-25 DALI Interface (primary side; for DA-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output. Smart timer dimming function (for Dxx-Type by User definition) MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications.

7 If other options may be needed, please contact MEAN WELL for details. Ex : D01-Type: the profile recommended for residential lighting Ex: D02-Type: the profile recommended for street lighting**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level. Example: If a residential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:[1] The power supply will switch to the constant current level at 100% starting from 6:00pm. [2] The power supply will switch to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the power supply turns on.[4] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on.

8 The constant current level remains till 8:00am, which is 14:00 after the power supply turns on.**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming : If a street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance:[1] The power supply will switch to the constant current level at 50% starting from 5:00pm. [2] The power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the power supply turns on. [3] The power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on.[4] The power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on.[5] The power supply will switch to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the power supply turns on.

9 The constant current level remains till 6:30am, which is 14:00 after the power supply turns up for D01-Type in Smart timer dimming software program: Set up for D02-Type in Smart timer dimming software program:TIME**TIME**06:0001:00T1T1T2T2T3 T3T4T4T507:0003:0011:008:0011:00------LE VEL**LEVEL**100%70%80%50%50%100%70%60%80 %Dimming Level(%)Operating Time(HH:MM)Dimming Level(%)Operating Time(HH:MM)70~100W Constant Voltage + Constant Current LED DriverELG-100 seriesFile Name: ELG-100 -SPEC 2020-09-25Ex: D03-Type: the profile recommended for tunnel lighting Set up for D03-Type in Smart timer dimming software program: TIME**01:30T1T2T311:00---LEVEL**70%100%7 0%**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming : If a tunnel lighting application adopts D03-Type, when turning on the power supply at 4:30pm, for instance:[1] The power supply will switch to the constant current level at 70% starting from 4:30pm.

10 [2] The power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on. [3] The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30am, which is 14:00 after the power supply turns Level(%)Operating Time(HH:MM)70~100W Constant Voltage + Constant Current LED DriverELG-100 seriesFile Name: ELG-100 -SPEC 2020-09-25808284868890929450%60%70%80%90 %100%277V(100W)230V(100W)115V(80W)-40-25 0 10305070859020406080100 PFLOADOUTPUT LOAD vs TEMPERATURE( )STATIC CHARACTERISTICTOTAL HARMONIC DISTORTION (THD)AMBIENT TEMPERATURE,Ta () CLOAD (%)INPUT VOLTAGE (V) 60 HzLOAD (%)(HORIZONTAL)POWER FACTOR (PF) CHARACTERISTICT case () CLOAD (%)(HORIZONTAL) De-rating is needed under low input vs LOADELG-100 series possess superior working efficiency that up to 91% canbe reached in field applications.