Emerson Smart Wireless Gateway 1420

1 Quick Start Guide00825-0200-4420, Rev GBJune 2017 Emerson Smart Wireless Gateway Page 1 Wednesday, June 28, 2017 8:01 AMJune 20172 Quick Start GuideNOTICEThis guide provides basic guidelines for the Smart Wireless Gateway . It does not provide instructions for diagnostics, maintenance, service, or troubleshooting. Refer to the Smart Wireless Gateway Reference Manual (document number 00809-0200-4420) for more information and instructions. This guide and the manual are available electronically on could result in death or serious injury. Installation of this device in an explosive environment must be in accordance with the appropriate local, national, and international standards, codes, and practices.

2 Review the Product Certifications section for any restrictions associated with a safe installation. Avoid contact with the leads and terminals. High voltage may be present on leads can cause electrical device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. This device must be installed to ensure a minimum antenna separation distance of 20 cm from all Wireless considerations .. 3 General considerations .. 3 Initial connection and configuration.

3 4 Physical installation .. 10 Connect to the host system .. 15 Software installation (optional) .. 16 Verif y operations .. 16 Product specifications .. 17 Product Certifications .. Page 2 Wednesday, June 28, 2017 8:01 AMQuick Start Guide3 June Wireless Power up sequenceThe Smart Wireless Gateway ( Gateway ) should be installed and functioning properly before power modules are installed in any Wireless field devices. Wireless field devices should also be powered up in order of proximity from the Smart Wireless Gateway beginning with the closest. This will result in a simpler and faster network Antenna positionThe antenna should be positioned vertically, and be approximately 3 ft.

4 (1 m) from large structures or buildings to allow for clear communication to other Mounting heightFor optimal Wireless coverage, the Gateway or remote antenna is ideally mounted 15 to 25 ft. (4,6 to 7,6 m) above ground or 6 ft. (2 m) above obstructions or major Gateway redundancyIf the Wireless Gateway was ordered with redundancy ( Gateway Redundancy code RD), refer to Appendix D in the Smart Wireless Gateway Reference Manual (document number 00809-0200-4420) for additional installation General PC requirementsOperating system (optional software only) Microsoft Windows XP Professional, Service Pack 3 Windows Server 2003 Service Pack 2 Windows Server 2003 R2 Service Pack 2 Windows Server 2008 (Standard Edition)

5 , Service Pack 2 Windows Server 2008 R2 Standard Edition, Service Pack 1 Windows 7 Professional, Service Pack 1 Windows 7 Enterprise, Service Pack 1 Applications Internet Explorer or higher Mozilla Firefox or higher .Net Framework (for OPC proxy only)Hard disk space AMS Wireless Configurator: GB Gateway Setup CD: 250 Page 3 Wednesday, June 28, 2017 8:01 AMJune 20174 Quick Start Initial connection and DeltaV readyIf the Gateway was ordered DeltaV Ready (Data Protocols Code 5), then skip to Physical installation, and connect the Gateway to a DeltaV or newer control Initial connection and configurationTo configure the Smart Wireless Gateway , a local connection between a PC/laptop and the Gateway needs to be the GatewayBench top power will be needed to power the Gateway by wiring a 24 VDC (nominal) power source, with at least 250 mA, to the power terminals.

6 Figure 1. Legacy Gateway Terminal Block DiagramFigure 2. Power over Ethernet (PoE) Terminal Block Diagram+++++-----ABSSSS24 VDC (nominal)Power InputSerialModbusNot UsedNot UsedNot UsedNot UsedCase(Covered)SEthernet 2 with PowerEthernet 2 Ethernet 1(Secondary)(Primary) +-AB24 VDC (nominal)Power InputSerialModbusCaseSEthernet 2 Ethernet 1(Secondary)(Primary) Page 4 Wednesday, June 28, 2017 8:01 AMQuick Start Guide5 June 2017 NoteFigure 1 depicts the terminal block of legacy Gateways prior to the introduction of PoE capabilities. Figure 2 shows the terminal block arrangement of a PoE version of the Gateway . If the Gateway will be powered via the standard 24 volt power input terminals, and no PSE is desired, it is not necessary to change the default settings of the PoE jumper Gateway enclosure case should always grounded in accordance with national and local electrical codes.

7 The most effective grounding method is a direct connection to earth ground with minimal impedance. Figure 3. 1420 PoE Jumpering Matrix (Located on 1420 Board)Legend:ETH1: Ethernet port 1 selected for PD or PSEETH2: Ethernet port 2 selected for PD or PSEPD: Gateway derived its power off the Ethernet port selectedPSE: The Gateway is powered via the standard 24 volt power input terminals and provides power via the selected Ethernet port to another device with a compatible PD : Enabled; this enables the PSE operationDIS: Disabled; this disables the PSE operation PoE PD on port 1(Default jumpering forproduction. Used for no PoE also)PoE PD on port 2 PoE PSE on port 1 PoE PSE on port 2 Black fill below indicates Page 5 Wednesday, June 28, 2017 8:01 AMJune 20176 Quick Start GuideNoteElectrostatic discharge (ESD) protection required when swapping PoE one port and one mode of operation (PD or PSE) can be selected at a time; any other combination of jumpers is PoE standard provides up to W of DC power (minimum 44 V DC and 350 mA) to each device.

8 Only W is assured to be available at the powered device as some power is dissipated in the PoE standard also known as PoE+ or PoE plus , provides up to W of power. The 2009 standard prohibits a powered device from using all four pairs for more information on PoE and frequently asked questions, reference document number Establishing a connectionNoteFor information on connecting a Windows 7 PC, see Technical Note (document number 00840-0900-4420).1. Connect the PC/laptop to the Ethernet 1 (Primary) receptacle on the 4. Gateway PC/Laptop ConnectionA. PC/laptopB. Ethernet 1 receptacleDo not connect to the Ethernet 2 with power (covered) port.

9 This port supplies power and could damage the PC/laptop.+++++-----ABSSSSS24 V DC24 V DCPower InputPower InputModbusModbusNot UsedNot UsedNot UsedNot UsedNot UsedNot UsedNot UsedNot Page 6 Wednesday, June 28, 2017 8:01 AMQuick Start Guide7 June 20172. To establish the PC/laptop settings, navigate to Start>Settings>Network Select Local Area Right click to select Select Internet Protocol (TCP/IP), then select the Properties the PC/laptop is from another network, record the current IP address and other settings so the PC/laptop can be returned to the original network after the Gateway has been Select the Use the following IP address button.

10 E. In the IP address field, enter In the Subnet mask field, enter In the Internet Protocol (TCP/IP) Properties window, select In the Local Area Connection Properties window, select Page 7 Wednesday, June 28, 2017 8:01 AMJune 20178 Quick Start GuideNoteConnecting to the Gateway 's secondary Ethernet port requires different network settings. Refer to Ta b l e 1 for additional network 1. Default IP AddressesTable 2. Subnet Settings3. Disable Open a standard web browser (Internet Explorer, Mozilla Firefox, or other).b. Navigate to Tools>Internet Options>Connections>LAN Settings. c. Uncheck the box under Proxy 1 1 (DeltaV Ready) 2 (DeltaV Ready) Page 8 Wednesday, June 28, 2017 8:01 AMQuick Start Guide9 June Configure the Smart Wireless GatewayTo complete initial configuration for the Gateway :1.