ENGINEERING STANDARD FOR PROCESS DESIGN …

1 IPS-E-PR-420 This STANDARD is the property of Iranian Ministry of Petroleum. All rights are reserved to the owner. Neither whole nor any part of this document may be disclosed to any third party, reproduced, stored in any retrieval system or transmitted in any form or by any means without the prior written consent of the Iranian Ministry of Petroleum. ENGINEERING STANDARD FOR PROCESS DESIGN OF HEAT TRACING AND WINTERIZING ORIGINAL EDITION JAN. 1996 This STANDARD specification is reviewed and updated by the relevant technical committee on Mar.

2 2001. The approved modifications are included in the present issue of IPS. Jan. 1996 IPS-E-PR-420 1 CONTENTS : PAGE No. 0. 3 1. 4 2. 4 3. SYMBOLS AND 4 4. 5 5. APPLICATION AND 5 General 5 Methods of 5 6. CONDITIONS REQUIRING 6 7. 6 6 7 PROCESS 7 Piping for water 8 8 Level 9 Flow 9 Control 9 Temperature 10 Lead lines and 10 10 Analyzing 10 10 11 Drum, vessel, storage 11 11 Pumps and 11 Miscellaneous 12 Hydrants, monitors, spray and deluge 12 Emergency (safety) showers and 12 Drainage separators, sumps and 13 Chemicals and 13 8.

3 13 Internal Steam 13 External Steam 13 13 Steam 15 Jan. 1996 IPS-E-PR-420 Steam 17 Condensate 17 Steam tracing lines (tracers).. 18 Installation of 19 Instrum entation tracer 20 Steam 21 21 Inspection and 21 Electrical 21 21 Use of Heat Transfer 22 APPENDICES: APPENDIX 24 APPENDIX 25 APPENDIX 26 APPENDIX 27 Jan. 1996 IPS-E-PR-420 30. INTRODUCTION The primary purpose of IPS STANDARD specifications on " PROCESS DESIGN of General Heating & Cooling and Flushing Systems" is to establish minimum requirements and DESIGN criteria needed in " PROCESS DESIGN " of the following standards.

4 STANDARD CODE STANDARD TITLE IPS-E-PR-400 " PROCESS DESIGN Cooling of Water Circuits" IPS-E-PR-410 " PROCESS DESIGN of Hot Oil, & Tempered Water Circuits" IPS-E-PR-420 " PROCESS DESIGN of Heat Tracing and Winterizing" The specifications and basic practices covered under these Standards are made in the light of available existing accumulated information and knowledge experienced and known to the Company at the time of writing, but it has been impossible to consider every possible factor that might affect PROCESS DESIGN on a particular point.

5 This ENGINEERING STANDARD Specification covers: " PROCESS DESIGN OF HEAT TRACING AND WINTERIZING" Jan. 1996 IPS-E-PR-420 41. SCOPE This STANDARD Specification covers the minimum requirements for protection of PROCESS and utilities and all associated equipment and flow lines and instruments against the temperature which would cause congealing or freezing of contents, interfere with operation or cause damage to equipment or pipe lines and for heat conservation requirement as would be determined by PROCESS conditions.

6 The heat conservation system shall be designed for continuous operations while, winterizing shall be for seasonal operation. The two systems shall be separate from each other. Note: This STANDARD specification is reviewed and updated by the relevant technical committee on Mar. 2001. The approved modifications by were sent to IPS users as amendment No. 1 by circular No. 166 on Mar. 2001. These modifications are included in the present issue of IPS. 2. REFERENCES Throughout this STANDARD the following dated and undated standards/codes are referred to.

7 These referenced documents shall, to the extent specified herein, form a part of this STANDARD . For dated references, the edition cited applies. The applicability of changes in dated references that occur after the cited date shall be mutually agreed upon by the Company and the Vendor. For undated references, the latest edition of the referenced documents (including any supplements and amendments) applies. IPS (IRANIAN PETROLEUM STANDARDS) IPS-E-PR-230 "Piping & Instrumentation Diagrams (P&IDS)" IPS-M-EL-190 "Electrical Heat Tracing" IPS-C-TP-701 "Thermal Insulations" IPS-E-TP-700 "Thermal Insulations" API (AMERICAN PETROLEUM INSTITUTE) API RP-550, Section , "Winterizing", 4th.

8 Ed., October 1980 3. SYMBOLS AND ABBREVIATIONS CM = Collection Manifold DM = Distribution Manifold DN = Diameter Nominal (Pipe Size), in (mm) ET = Electric Traced and Insulation ETT = Electric Traced with Heat Transfer Cement H = Heat Conservation ID = Inside Diameter MI = Mineral Insulation PD = Positive Displacement Meters Meters P & IDS = Piping and Instrumentation Diagrams Ref.

9 = Reference Jan. 1996 IPS-E-PR-420 5OD = Outside Diameter SJ = Steam Jacketing Pipe and Insulation ST = Steam Traced and Insulation STS = Steam Traced with Spacers and Insulation STT = Steam Traced with Heat Transfer Cement and insulation UOP = Universal Oil Products W = Winterization WS = Winter Seal WISI = Winterize Insulator, Steam Trace, Insulate 4. UNITS This STANDARD is based on International System of Units (SI) except where otherwise is specified.

10 5. APPLICATION AND METHODS General Considerations To avoid operating difficulties in PROCESS and utility Units in colder climates and the hazard of freezing which may cause damage to equipment or blockage of lines, different methods to the extent of protection required, will be used. The extent of protection may vary considerably between one location and another. However, the requirements for other ambient temperature conditions is also covered herein. Methods of Winterization The following methods of winterization is required to be used for adequate protection as will be determined by combined climatic and PROCESS condition for seasonal operation and heat conservation.