Fenwal 732 Operating Instructions - Kidde Fenwal

1 Fenwal 732 Operating Instructions Normal Standby Operation Alarm Reset Switch Functions Green AC ON LED lit steadily Press SYSTEM RESET , panel will return to normal 1) Press OUTPUT DISABLE button to disable outputs, standby operation. SYSTEM SUP LED flashes. All other LEDs OFF. NOTE: If alarms, troubles, or supervisory conditions still 2) Subsequent button press enables outputs, SYSTEM SUP. A series of 3 dots ( ) scrolls across the display remain active on the inputs, the panel will return to that LED goes off. Alarm Condition condition. 3) If any input is activated while Output Disable is active, These actions occur when any alarm condition is reported: Supervisory Condition press System Reset before canceling Output Disable. 1) Appropriate red alarm LED and SYSTEM ALM LED flashes These actions occur when any supervisory condition is 2) Buzzer on continuously reported: Lamp Test 3) Signal circuit devices on as programmed 1) Appropriate SUP# LED flashes.

2 1) Press the ACKNOWLEDGE button continuously for a 4) Programmed release time delay is activated, if selected. 2) SYSTEM SUP LED flashes. minimum of five seconds. 5) The programmable relays actuate as configured. 3) Buzzer pulses if there is no alarm active. 4) Programmed relay outputs activate as configured. 2) All LEDs and the seven-segment display will turn on. What To Do When an Alarm Occurs 3) Release ACKNOWLEDGE button to end test. Press the ACKNOWLEDGE button to change an alarm What To Do If a Supervisory Message Occurs LED from flashing to steady, and to silence the internal Press the ACKNOWLEDGE button to change a Maintenance and Testing buzzer. It may be necessary to press the supervisory LED from flashing to steady, and to silence ACKNOWLEDGE button more than once if multiple alarm the internal buzzer.

3 It may be necessary to press the Warning! events have occurred. ACKNOWLEDGE button more than once if multiple Be sure that all suppression systems are disconnected supervisory events have occurred. according to the manufacturer's Instructions before you How to Silence Audible Notification Appliances perform any maintenance or testing on this control unit. Supervisory indicators clear when the condition is Press the SIGNAL SILENCE button to de-activate any resolved. Latching Supervisories require a System Reset. silenceable outputs, such as notification appliances. The Standby-Battery Replacement yellow SIGNAL SILENCED LED will go on steady. Trouble Condition Refer to the Fenwal 732 Installation, Operation, &. A subsequent press of the SIGNAL SILENCE button will These actions occur when any trouble condition is Maintenance Manual, P/N 06-236717-001, to test the re-activate any outputs that were silenced if no new alarm reported: standby batteries.

4 Replace batteries every three years, or events have been reported since the outputs were more frequently as recommended by the manufacturer. 1) An appropriate trouble LED flashes. silenced. The SIGNAL SILENCED LED will go off. 2) SYSTEM TBL LED flashes. System Maintenance and Testing This toggling capability will remain in effect until the 3) Buzzer pulses if there is no supervisory or alarm active. control unit is reset. 4) Programmed relay outputs activate as configured. Refer to the Fenwal 732 Installation, Operation, &. Maintenance Manual, P/N 06-236717-001, for What To Do When a Trouble Message Occurs recommended testing and maintenance procedures. Operation of Abort Discharge is aborted only when an Alarm is from a Press the ACKNOWLEDGE button to change the trouble detector and Abort is activated during programmed LEDs from flashing to steady and to silence the internal Local Service Company release time delay.

5 Abort sequence is dependent on buzzer. It may be necessary to press the programming. ACKNOWLEDGE button more than once if multiple NAME: _____. trouble events have occurred. 1) Press ABORT switch if installed. 2) ABORT LED will go on. ADDRESS: _____. Trouble indicators clear when the condition is resolved. 3) Release countdown will abort as programmed. Latching Troubles require a System Reset. (See Fenwal 732 Installation, Operation, & Maintenance _____. Manual, P/N 06-236717-001, for exceptions.). 4) Release ABORT switch. LED will go off. TEL NO.: _____. 5) Countdown will continue as programmed. NOTE: A MANUAL RELEASE will override an ABORT switch. FRAME AND POST ADJACENT TO PANEL Part No. 06-236719-001 Rev AB.