FLUIDMASTER 400UK BOTTOM INLET VALVE …

1 7. IMPORTANT: ALWAYS CLEAR DEBRIS FROM WATER LINE TO COMPLETE off watersupply to cistern. Remove VALVETOP by lifting arm and rotating TOP 1/8 turn anti-clockwise, pressing downslightly on cap. While holding a container over the uncappedVALVE to prevent splashing, turn water supply onand off to clear debris that may be in supply off water supply and replace TOP by engaging lugs and rotating1/8 turn clockwise. MAKE CERTAINTOP IS TURNEDTOTHE LOCKED MAY NOT TURN ON IF TOP IS NOTFULLY TOTHE LOCKED off water more informationin the contact: FLUIDMASTER UKOne Harbour RoadPortishead, BristolBS20 7 BLTel: 01275 84 88 43 FAX: 01275 81 74 37 EMAIL: GET THE BEST RESULTS FROM YOUR FLUIDMASTER VALVE ,PLEASE READ THESE INSTRUCTIONS : SAVE INSTRUCTION SHEET FOR FUTURE REFERENCECONCERNINGTHISVALVE S OPERATIONAND.

2 DO NOT use plumber s putty to seal this off water supply to toiletcistern at storage tank in loft orisolator VALVE if mains Disconnect pipe work andremove old VALVE fromtoilet cistern5. Install VALVE inside to thread back nut ontothreaded shank so the shankprotrudes through the cisternenough to enable tap connector tofit neatly. Do not tighten back nutat this position is correct andbefore tightening back nut,reconnect water supply to VALVE tomake sure fibre washer is sealedcorrectly. Tighten tap connector1/4 turn past hand tight withspanner (DO NOT OVERTIGHTEN).

3 Now tighten back nut with spanner1/4 turn past hand tight (DO NOTOVERNIGHTEN).Turn on mainwater the water to the desired levelby turning the water level adjustment rodand moving float cup up or be set to water line on Place sealing washer onthreaded shank of VALVE in toilet cistern,passing threaded shank throughhole in cistern to determine ifvalve height needs The FLUIDMASTER 400UK valveis adjustable in height from225mm (9 inches) to 350mm(14 inches).To adjust height ofvalve, remove from toilet cisternand twist threaded shank in or outof VALVE body.

4 A clicking noise willbe heard on some VALVE height shouldbe adjusted so that the criticallevel mark on the VALVE body islocated at least 25mm (1 inch)above the overflow pipe inthe 400UK BOTTOM INLETVALVE INSTALLATION INSTRUCTIONSFORTOILET CISTERNWARNING: FLUIDMASTER shall not be responsible or liable for any failure of, ordamage to, this plumbing product caused by use of chlorine (bleach) cleaners orrelated products added to the toilet cistern. Use of such products will void thewarranty and may result in product failure, possibly causing property not overtighten plastic 002 Rev.

5 2 10/06 GUARANTEE:This Fluidmasterproduct is guaranteedto be free fromdefective materials andworkmanshipfor aperiod of one year. Unitsreturned to FLUIDMASTER ,USA, or FLUIDMASTER UKwill be replacedwithout use qualityFluidmasterrepair partswhen maintaining yourFluidmaster shall not beresponsible or liable forany damages caused byproducts used inFluidmaster valves thatwere notmanufactured byFluidmaster, off water supply as in Figure 1 of Remove upper cap assembly by lifting arm and rotating 1/8 Replace seal and refit upper cap assembly. Make sure upper assembly is fully turned clockwise to the on water supply as - SEAL REPLACEMENT: If VALVE won t turn on or shut off orrefill ofcistern water is slow after valvehas been in use forsome time, a replacement your dealerfor Model242MP071 and install as follows:1.

6 Turn off water supply in Figure 1of Removewaterleveladjustmentrod from upper cap assembly as Removeupper capassembly by lifting armand rotating 1/8 anti-clockwise, pressingdown slighty on Hold a cup over the uncappedvalve (to preventsplashing), and turnwatersupplyonandoff to clear debris in Refitupper capassembly. Make sure assembly is fullyturnedclockwise tothe locked position or VALVE willnot turn to upper assemblyby snapping back in Turn on watersupply as UKTwyford RoadRotherwas, Hereford, HR2 6 JRTel: 01432 357331 Fax: 01432 264014E-MAIL.