QUICK Install Guide

1 400A FILL VALVE*See back page for important legal - Page 14 Install WITH CONFIDENCEQUICK Install GuideHOW-TO VIDEOVIDEOVISIT: PRODUCT PAGE23 STEP 1: PREPARE TANKGETTING STARTEDPARTS OVERVIEWTank Water LevelAdjustment Screw A: TURN OFF WATERTOP DOWN VIEW B: DRAIN WATER Flush toilet to drain most of the water from the tank. C: USE SPONGE OR TOWEL TO SOAK UP EXCESS WATER IN TANKFLUSHT owelSpongeTOOLS NEEDEDS pongeBucketTowelScissors(Optional)Locknu tShank WasherRefill TubeTank Water LevelAdjustment ScrewRefill ClipTURNCLOCKWISE4 STEP 2: REMOVE OLD FILL VALVE5 STEP 3: ADJUST HEIGHT OF NEW FILL VALVE LEFT LEFT A: REMOVE CONNECTOR Remove water supply connector from bottom of fill valve by twisting connector nut to the left (clockwise).

2 B: REMOVE OLD LOCKNUT Below tank, twist locknut to the left (clockwise) to remove from fill valve. C: REMOVE OLD FILL VALVE Including refill tube, refill clip and shank washer. Drain any excess water into bucket by removing fill valve from tank. (Pull fill valve up)Bucket(Optional) A: TWIST FILL VALVE TO ADJUST HEIGHT Top of fill valve cap should measure roughly 3" above top of overflow pipe when : Inspect watersupply it if it is worn, oryou don t know how old it is, toprevent flooding and property (Optional)NOTE:Increasing height allowsmore water to fill in the Not Move Lock RingTOP OF FILL VALVE CAPTOP OF OVERFLOW PIPE3"Fill Valve CapOverflow Pipe* The top of the overflow pipe must be a minimum of 1" below tank lever hole.

3 *Lever Hole67 STEP 4: Install NEW FILL VALVESTEP 5: FINISHING STEPSA: PUSH REFILL TUBE ONTO FILL VALVE REFILL PORTE: Install LOCKNUT Screw locknut to the right (counterclockwise) onto fill valve shank (below tank). *Hand-tighten only. DO NOT OVER : ATTACH REFILL CLIP TO OTHER END OF REFILL TUBE A: ATTACH WATER SUPPLY CONNECTOR TO FILL VALVE Twist to the right (counterclockwise) *Hand-tighten only. DO NOT OVER B: TURN ON WATER Check for leaks. (Go to for leak solutions.) C: WATER LEVEL After the tank stops filling, water level should fill the tank to roughly inch below top of overflow pipe to ensure a proper flush.

4 (Does not need to be exact.)C: INSERT FILL VALVE Position refill tube to face flush valve making sure fill valve parts do not interfere with lever TubeLever ArmOverflow PipeFill ValveRIGHT* Over tightening may crack the fill valve or tank causing flooding. Make sure the float cup does not touch the tank walls or tank lever and flush valve. Over tightening may crack the fill valve or tank causing flooding. Make sure the float cup does not touch the tank walls or tank lever and flush valve.** The top of the overflow pipe must be a minimum of 1" below tank lever LevelOverflow PipeTop ofOverflow Pipe1/2"D: ATTACH REFILL CLIP TO OVERFLOW PIPE Note: If refill tube is too long to fit inside tank with lid closed, remove refill tube from fill valve refill port, cut tube, and reattach to (Optional)**Lever Hole*89 STEP 6: FINE-TUNE TANK WATER LEVELSTEP 7: FLUSH THE TOILET A.

5 FLUSH THE TOILET TO CHECK THE TANK WATER LEVEL After the water stops filling the tank, the water level should be roughly inch below the top of overflow pipe to ensure a proper flush. B: WATER LEVEL IS TOO LOW Turn the tank water level adjustment screw clockwise to raise the float. Flush to reset water level. WATER LEVEL IS TOO HIGH Turn the water level adjustment screw counterclockwise to lower the float. Flush to reset water level. A: FLUSH THE TOILET If you re satisfied with the flush, YOU RE DONE!Still not working exactly right?

6 See the next page for DID IT!We knew you could!Share your success storywith friends and family!#FixedMyToilet#Fluidmaster1/2"Ove rflowPipeSee Step 5C for Full Tank viewTank Water LevelAdjustment Screw+ 1011 TROUBLESHOOTINGSee Our TroubleshootingHOW-TO THE FILL VALVE: DOES NOT TURN ON WON T TURN OFF WON T REFILL TANKREMOVE CAP AND CHECK FOR DEBRIS A: Turn off water supply. B: Flush toilet. C: With right hand push float up, grip and hold shaft under float. D: With left hand twist cap and lever arm counterclockwise to unlock cap. Let cap hang on float cup.

7 E: Hold empty cup upside down over uncapped valve to prevent splashing. F: Turn water supply on and off a few times. G: Turn water supply off. H: Replace valve Place cap assembly on top of gray valve body by aligning cap arm and adjustment rod next to refill tube. Press down on top cap while rotating top & arm clockwise to locked position. A: WATER FROM REFILL TUBE MUST FLOW THROUGH OVERFLOW PIPE Make sure the refill tube is supplying water down overflow pipe. (Metal side out for refill clip) B: WATER LEVEL IN TANK MAY BE TOO LOW 1/2 below top of overflow pipe is recommended (see page 8).

8 WATER LEVEL IN BOWL IS TOO LOWO verflowPipeRefill Tube1/2"OverflowPipeREPLACE FILL VALVE SEAL Place cap assembly on top of gray valve body by aligning cap arm and adjustment rod next to refill tube. Press down on top cap while rotating top & arm clockwise to locked position. A: Remove cap (see page 10). B: Replace seal with a *genuine Fluidmaster 242 Seal. C: Replace valve cap.* Always use genuine Fluidmaster parts when installing or repairing. Fluidmaster will not be responsible or liable for use of non-Fluidmaster parts during installation or QUESTIONS?

9 For installation assistance, contact ourtechnical services , CHAT or CALLour toll-free Available:Monday Friday 5:30 AM - 5:00 PM PSTThe Fluidmaster refill clip is not required for you ve already installed the refill clip onto the refill tube, simply pull it or cut it off. Push refill tube into refill hole at the top of the flush valve refill tube onto yellow nipple on flush refill tube onto refill clip, then attach refill clip to flush valve overflow pipe. Reuse original refill clip. Do not use Fluidmaster refill CANISTER FLUSH VALVESFOR MANSFIELD FOR KOHLER AQUAPISTON FOR AMERICAN STANDARD CHAMPION 31415GU A DE INSTALACI N R PIDAINSTALE CON CONFIANZA*Consulte la ltima p gina para obtener informaci n legal NECESARIA Balde, Esponja, Toalla, TijerasEMPEZANDO: RESUMEN DE PIEZASVIDEO DEC MO HACERLOVISITE.

10 DE ESPECIFICACIONESDEL PRODUCTO 400 AVIDEOV LVULA DE LLENADO 400 ATornillo de Ajuste del Nivel del Agua del TanqueVISTA DESDE ARRIBAC ontratuercaJunta del V stagoManguera de RellenoTornillo de Ajuste del Nivel del Agua del TanqueGancho de RellenoNivel del aguaTubo de Desag e Parte Superior del Tubo de Desag e 1,27 CMGU A DE INSTALACI N R PIDAPASO 1: PREPARE EL TANQUE (P GINA 3)A: CIERRE EL : DRENE EL AGUA. Descargue el sanitario para drenar la mayor a del agua del : USE LA ESPONJA O LA TOALLA PARA REMOVER EL EXCESO DE AGUA EN EL : REMUEVA EL CONECTOR.