FLUIDMASTER 400UK BOTTOM INLET VALVE …

1 7. IMPORTANT: ALWAYS CLEAR DEBRIS FROM WATER LINE TO COMPLETE off watersupply to cistern. Remove VALVE TOP by lifting arm and rotating TOP 1/8 turn anti-clockwise, pressing downslightly on cap. While holding a container over the uncapped VALVE to prevent splashing, turn water supply onand off to clear debris that may be in supply line. Turn off water supply and replace TOP by engaging lugs and rotating1/8 turn clockwise. MAKE CERTAIN TOP IS TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOTFULLY TO THE LOCKED POSITION. Turn off water more informationin the contact: FLUIDMASTER UKOne Harbour RoadPortishead, BristolBS20 7 BLTel: 01275 84 88 43 FAX: 01275 81 74 37 EMAIL: GET THE BEST RESULTS FROM YOUR FLUIDMASTER VALVE ,PLEASE READ THESE INSTRUCTIONS : SAVE INSTRUCTION SHEET FOR FUTURE REFERENCECONCERNING THIS VALVE S OPERATION AND : DO NOT use plumber s putty to seal this Turn off water supply to toiletcistern at storage tank in loft orisolator VALVE if mains Disconnect pipe work andremove old VALVE fromtoilet cistern5.

2 Install VALVE inside to thread back nut ontothreaded shank so the shankprotrudes through the cisternenough to enable tap connector tofit neatly. Do not tighten back nutat this When position is correct andbefore tightening back nut,reconnect water supply to VALVE tomake sure fibre washer is sealedcorrectly. Tighten tap connector1/4 turn past hand tight withspanner (DO NOT OVERTIGHTEN).Now tighten back nut with spanner1/4 turn past hand tight (DO NOTOVERNIGHTEN). Turn on mainwater Adjust the water to the desired levelby turning the water level adjustment rodand moving float cup up or down. Watershould be set to water line on Place sealing washer onthreaded shank of VALVE in toilet cistern,passing threaded shank throughhole in cistern to determine ifvalve height needs The FLUIDMASTER 400UK valveis adjustable in height from225mm (9 inches) to 350mm(14 inches).

3 To adjust height ofvalve, remove from toilet cisternand twist threaded shank in or outof VALVE body. A clicking noise willbe heard on some models. This isnormal. The VALVE height shouldbe adjusted so that the criticallevel mark on the VALVE body islocated at least 25mm (1 inch)above the overflow pipe inthe 400UK BOTTOM INLETVALVE installation INSTRUCTIONSFOR TOILET CISTERNWARNING: FLUIDMASTER shall not be responsible or liable for any failure of, ordamage to, this plumbing product caused by use of chlorine (bleach) cleaners orrelated products added to the toilet cistern. Use of such products will void thewarranty and may result in product failure, possibly causing property not overtighten plastic #446-1 Rev. 3 05/12 GUARANTEE:This Fluidmasterproduct is guaranteedto be free fromdefective materials andworkmanship for aperiod of one year.

4 Unitsreturned to FLUIDMASTER ,USA, or FLUIDMASTER UKwill be replacedwithout use qualityFluidmaster repair partswhen maintaining yourFluidmaster shall not beresponsible or liable forany damages caused byproducts used inFluidmaster valves thatwere notmanufactured byFluidmaster, Turn off water supply as in Figure 1 of Remove upper cap assembly by lifting arm and rotating 1/8 Replace seal and refit upper cap assembly. Make sure upper assembly is fully turned clockwise to the Turn on water supply as - SEAL REPLACEMENT: If VALVE won t turn on or shut off or refill ofcistern water is slow after VALVE has been in use for some time, a replacement seal may beneeded. Ask your dealer for Model 242MP071 and install as follows:1. Turn off water supply in Figure 1 of Remove water level adjustment rod from upper cap assembly as Remove upper cap assembly by lifting arm and rotating 1/8 anti-clockwise, pressing down slighty on Replace Hold a cup over the uncapped VALVE (to prevent splashing), and turnwater supply on and off to clear debris in Refit upper cap assembly.

5 Make sure assembly is fully turnedclockwise to the locked position or VALVE will not turn on. Reattach waterlevel adjustment rod to upper assembly by snapping back in Turn on water supply as before.