Transcription of FRBH - Flowserve
1 frbh . Heavy-Duty Paper Stock and Process Pump Maintenance Checklist Read User Instructions before installing, operating or maintaining this pump. Copies available from Flowserve pump representatives. Recommended Oil Lubricants Oil Splash / Force Feed / Purge Oil Mist Lubrication Pure Oil Mist Viscosity cSt 32 46 68 100. @ 40 C (104 F). Oil Temperature -5 to 65 C -5 to 78 C -5 C and above -30 C and above Range1 (23 to 149 F) (23 to 172 F) (23 F and above) (-22 F and above). Designation to ISO ISO VG 32 ISO VG 46 ISO VG 68 ISO VG 100. 3448 and DIN51502 32 HL/HLP 46 HL/HLP 68 HL/HLP . BP Energol HL32 BP Energol HL46 BP Energol HL68. BP . BP Energol HLP32 BP Energol HLP46 BP Energol HLP68.
2 Castrol Perfecto T32 Perfecto T46 Perfecto T68 . TERESSO 32 TERESSO 46 TERESSO 68. Esso . NUTO H32 NUTO H46 NUTO H68. LSC LSO 32 LSO 46 LSO 68 LSO 100. (for oil mist) Synthetic Oil Synthetic Oil Synthetic Oil Synthetic Oil Mobil DTE Oil Mobil DTE Oil Heavy Mobil DTE Oil Light Medium Medium Mobil . Mobil DTE13M Mobil DTE15M Mobil DTE26. Mobil DTE24 Mobil DTE25. Shell Tellus 32 Shell Tellus 01 C 46 Shell Tellus 01 C68. Shell Shell Tellus 37 Shell Tellus 01 46 Shell Tellus 01 68 . Shell Turbo T32 Shell Turbo T46 Shell Turbo T68. Rando Oil HD 32 Rando Oil 46 Rando Oil 68. Texaco Rando Oil Rando Oil Rando Oil . HD-AZ-32 HD B-46 HD C-68. Total Azolla ZS32 Azolla ZS46 Azolla ZS68.
3 1. Allow two hours for bearing temperature to stabilize. The final temperature will depend on the ambient, r/min, pumpage temperature and pump size. Some oils have a greater Viscosity Index than the minimum acceptable of 95 ( , Mobil DTE13M) which may extend the minimum temperature capability of the oil. Always check the grade capability where the ambient is less than -5 C (23 F). Oil and Grease Quantities 2 Relubrication Intervals 3. Bearing Oil Sump Initial Grease Capacities 71 to 79 C 79 to 93 C. <71 C. Frame Capacity Thrust Bearing Line Bearing Lubricant (160 to (175 to (160 F). Size No. L (gal) cm 3. in3 oz cm3 in3 oz 175 F) 200 F). 1 ( ) 120 6 200 10 Grease 6 mo 3 mo mo 2 ( ) 361 18 380 19 Mineral Oil 6 mo 3 mo mo 3 ( ) 680 34 559 28 Synthetic 18 mo 18 mo 18 mo 4 ( ) 917 36 620 31 Oil 3.
4 Assuming good maintenance and operation 2. Oil lubrication is standard. practices and no contamination. Vibration Seal Flush Requirements Maximum level: mm/s ( in/s) RMS Pressure: bar (10-15 psi) min. (measured on bearing housing surface) differential across seal faces Flow rate: m3/h (3-6 gpm). Alignment Align pump and motor shaft to within mm Impeller Axial Clearance ( in) parallel and mm/mm mm ( in). ( in/in) angular Impeller Balance Requirement Single plane spin balance: For 1180 rpm: oz in/lb For 1800 rpm: oz in/lb Recommended Grease Lubricants Shaft Data Grease Nipples Max. Shaft Deflection at Grease Seal Chamber NLGI 2 4 NLGI 3 5. Max. Shaft Runout at mm -20 to 100 C -20 to 100 C Seal Chamber ( in).
5 Temp. Range (-4 to 212 F) (-4 to 212 F). Max Shaft End Play DIN K2K-20 K2K-30 (Axial Movement). BP Energrease LS2 Energrease LS3. Recommended Bolt Torques DEA Glissando 20 Glissando 30. Torque, Nm (lbf-ft). Elf Elfmulti 2 Elfmulti 3 Bolt Size, in Pump Feet All Other Esso Beacon 2 Beacon 3 Fasteners Fasteners Mobil Mobilux 2 Mobilux 3 170 (125) 84 (62). Q8 Rembrandt 2 Rembrandt 3 340 (250) 165 (120). Alvania Fett G2 590 (435) 285 (210). Shell Alvania R3. Alvania Fett R2 1 770 (570) 375 (275). Multilak 20 Multilak 30 1 1100 (810) 540 (400). Texaco Multilak EP2 Multilak EP3 1 1840 (1350) 900 (660). Wintershall 1 2000 (1475) 1410 (1040). Wiolub LFK 2 - (BASF Group).
6 1 2240 (1650) 2060 (1500). SKF LGMT 2 LGMT 3. Silkolene G55/T G56/T Tightening Torque for Stainless Steel Studs With Lubricated Threads 4. NLGI 2 is an alternative grease and is not to be mixed with other grades. Thread Size, in Torque, Nm (lbf-ft). 5. Factory packed bearings for the temperature range with grease nipples. -16 UNC 13 (10). Maximum Recommended -13 UNC 27 (20). External Housing Temperature -11 UNC 60 (45). Lubrication Temperature -10 UNC 100 (75). Oil Bath/Oil Mist 82 C (180 F). Bearing Size (SKF). Grease 95 C (204 F). Thrust Bearing Line Frame Model (Paired Back-to- Bearing Maximum Temperature of Fluid Pumped Back). Without Cooling 120 C (250 F) 1 All 6311 7309 BUA.
7 With Cooling 176 C (350 F) 2 All 6316 7314 BUA. 3 All 6320 7318 BUA. Minimum Impeller Nut Tightening Torque 12 FRBH234. Frame Torque, Nm (lbf-ft) 14 FRBH244. 22222C. 1 140 (100) 16 FRBH244. 4 18 FRBH224 7322 BUA. 2 400 (300). 18 FRBH274. 3 400 (300) 20 FRBH304 22226C. 4 750 (550) 24 FRBH304. For sales and product information, go to FPD-1426a (E) Printed in USA. February 2011. Flowserve Corporation frbh pumps are manufactured in: Taneytown, MD (USA), and Brantford, ON (Canada). USA and Canada Europe, Middle East, Africa Latin America Asia Pacific Flowserve Corporation Flowserve Corporation Flowserve Corporation Flowserve Pte. Ltd. 5215 North O'Connor Blvd. Parallelweg 13 Mart n Rodriguez 4460 10 Tuas Loop Suite 2300 4878 AH Etten-Leur B1644 CGN-Victoria-San Fernando Singapore 637345.
8 Irving, Texas 75039-5421 USA The Netherlands Buenos Aires, Argentina Telephone: +65 6771 0600. Telephone: +1 937 890 5839 Telephone: +31 76 502 8100 Telephone: +54 11 4006 8700 Telefax: +65 6862 2329. Telefax: +54 11 4714 1610. Experience In Motio
