General Commands Reference Guide S

1 MANUAL Release Commands Reference Guide SGeneral Commands Reference Guide S | 2 1989-2022 Lauterbach General Commands Reference Guide STRACE32 Online Help TRACE32 Directory TRACE32 Index TRACE32 Documents .. General Commands .. General Commands Reference Guide S ..1 History ..14 SELFTEST ..15 SELFTESTE xecute selftest operation15 SETUP ..16 SETUPS etup commands16 analyzer display17 analyzer display17 analyzer display17 up MMU translation for breakpoints17 synchronization18 coloring for core-specific info in SMP systems18 configuration19 for hex-dumps20 softkeys configuration21 go to paused core21 interrupts during assembler step22 interrupts during HLL step22 source line

2 Symbol to run this action23 percentage in statistics window24 command24 single stepping on all cores25 step to skip breakpoint26 steps stops at assembler code26 step before go27 step HLL lines27 HLL lines with disabled breakpoints27 step to selected core28 stepping trail in list window28 step on SMP systems28 selective stepping29 of symbols29 General Commands Reference Guide S | 3 1989-2022 Lauterbach emulation monitor time-out30 for the Var commands31 call dummy routine34 pointer access35 verification for software breakpoints35 SIM.

3 36 SIMTRACE32 Instruction Set Simulators36 area for simulation output36 simulation and more37 the cache allocation technique38 memory coherency strategy39 MPU regions39 cache and MMU simulation40 cache and MMU simulation40 the replacement strategy40 the number of cache/TLB sets42 cache and MMU settings43 address mode for cache lines44 simulator trace method44 of memory accesses for cache simulation45 of TLB accesses for MMU simulation45 number of cache ways46 width of cache line46 command to simulation model47 interrupt47 loaded simulator models48 simulator module48 TRACE32 Instruction Set Simulator48 simulator module49 SLTrace.

4 50 SLTraceTrace sink for events50 configuration window51 SNOOPer ..52 SNOOPerSample-based trace52 SNOOPer-specific Trace Commands ..53 SNOOPer.<specific_cmds>Overview of SNOOPer-specific commands53 cores for PC snooping53 behavior on sampling errors54 operation mode of SNOOPer trace55 PC snooping59 sampling rate60 address for monitoring60 General Commands Reference Guide S | 4 1989-2022 Lauterbach trace buffer size62 trigger delay62 the trigger destination63 data value

5 For trigger64 Generic SNOOPer Trace Commands ..65 the trace65 automatically65 initialization65 a bookmark in trace listing65 trace contents graphically65 display graphically65 analysis66 activity chart66 trace contents66 the trace66 trace data against time66 no-data values against time66 variable values against time66 trace data for processing in other applications67 a file

6 Into the file trace buffer67 specified entry in trace67 all specified entries in trace67 for changes in trace flow67 input level67 cursor to specified trace record67 trace67 trace contents68 variable recorded to trace68 trace file for offline processing68 off68 charts68 a profile chart68 analysis in a table versus time68 analysis69 display for user-defined protocol69 display for user-defined protocol69 trace buffer for user-defined protocol69 in trace buffer for user-defined protocol69 trace buffer for user-defined protocol69 chart for user-defined protocol69 chart for user-defined protocol70 statistics for user-defined protocol70 Reference point for time measurement70 General Commands Reference Guide S | 5 1989-2022 Lauterbach

7 Command70 trace for postprocessing in TRACE3270 restart of trace recording70 trace capturing once70 trace configuration window71 analysis71 analysis71 of trace buffer71 tracking record71 single record71 timestamps of trace and timing analyzers71 SPE ..72 SPES ignal Processing eXtension (SPE)72 SPE registers72 SPE registers72 SPE register window73 SSE.

8 74 SSESSE registers (Streaming SIMD Extension)74 SSE registers74 SSE registers74 SSE registers75 StatCol ..76 StatColStatistics collector76 Step ..77 StepSteps through the program77 single-stepping77 back77 back till expression changes78 back78 back till expression true78 till expression changes79 till next unreached line80 single-stepping82 single-stepping82 over call83 till expression true84 STM.

9 85 STMS ystem trace configuration85 STOre ..86 STOreStore settings as PRACTICE script86 General Commands Reference Guide S | 6 1989-2022 Lauterbach SVE ..90 SVEA ccess the scalable vector extension SVE90 SVE registers90 SVE settings90 SVE registers90 SVE registers91 sYmbol ..92 sYmbolDebug symbols92 Overview sYmbol92 additional symbolic information94 symbol information to fixed address96 information97 information for ' ' commands98 additional information99 scaling information from ASAP2 file99 information to member of struct100 all additional information102 information to a data type102 information to a variable103 loading of

10 Symbols104 autoloader table105 dynamic autoloader106 automatic DLL file loader107 autoloader for Symbian108 autoloader for Linux debugging108 autoloader for QNX debugging109 autoloader for UEFI debugging109 autoloader110 autoloader110 symbol information111 symbol autoloader111