Example: biology
GK series LM Guide - THK
GK series LM Guide Rails and Blocks are individually Stocked for Easy/Fast Interchangeability CAT. NO. 410-3E 608-0272-H1.indd 1 2016/08/08 11:44:23
Information
Domain:
Source:
Link to this page:
Documents from same domain
Compliant with New Accuracy Standards Caged Ball LM …
tech.thk.com2 Global Standard Type Caged Ball LM Guide SHS LM block LM rail Endplate End seal Ball cage Ball Cross section 45。 45 。 Structure of Model SHS Balls roll in four rows of raceways precision-ground on an LM rail and an LM block, and ball cages and
Mounting Procedure and Maintenance LM Guide - …
tech.thk.comMounting Procedure <Example of Mounting the LM Guide When an Impact Load is Applied to the Machine and therefore Rigidity and High Accuracy are Required >
THK Original Grease AFE-CA Grease
tech.thk.comA THK Original Grease AFE-CA Grease Ô Base oil: high-grade synthetic oil Ô Consistency enhancer: urea-based AFE-CA Grease uses urea as a consistency enhancer and a high-grade synthetic oil as the base oil.
Models SHS-C and SHS-LC - THK Technical Support
tech.thk.comModel number coding A 5P EPXOMPBE B EFTJSFE EBUB TFBSDI GPS UIF DPSSFTQPOEJOH NPEFM OVNCFS JO UIF 5FDIOJDBM TJUF IUUQT UFDI UIL DPN Models SHS-C and SHS-LC (φH through)
Models SHS-V and SHS-LV - THK
tech.thk.comModel number coding A 5P EPXOMPBE B EFTJSFE EBUB TFBSDI GPS UIF DPSSFTQPOEJOH NPEFM OVNCFS JO UIF 5FDIOJDBM TJUF IUUQT UFDI UIL DPN Models SHS-V and SHS-LV B ¢K £ H3 M T 4-S ·ℓ W2 W W1 Model No. Outer dimensions LM block dimensions Pilot hole for side nipple Î Î Height Width Length
Caged Ball LM Guide Global Standard Size Model SHS
tech.thk.comA Types and Features Model SHS-C Speci Þ cation TableðA The ß ange of the LM block has tapped holes. Can be mounted from the top or the bottom. Used in places where the table cannot have
Features of the Ball Screw - THK Technical Support
tech.thk.comFeatures of the Ball Screw Driving Torque One Third of the Sliding Screw With the Ball Screw, balls roll between the screw shaft and the nut to achieve high ef Þ ciency.
Permissible Axial Load - THK
tech.thk.comA Permissible Axial Load <Buckling Load on the Screw Shaft > With the Ball Screw, it is necessary to select a screw shaft so that it will not buckle when the maxi-
Smooth Silent Ecological - THK Technical Support
tech.thk.comSpecial Environmental Specifications of Linear Motion Systems HSR HR HRW SR RSR SSR SHW SRS Clean Rooms HSR-M2 LM Guide with Caged Ball Technology Caged Roller LM Guide
Model DCM - THK
tech.thk.comA Lead Screw Nut D 1 PCD D Dr D o D k 4- B r 1- d H F L Unit: mm Screw shaft Screw shaft details Standard shaft length Maximum length Dynamic permis-sible thrust Static
Related documents
Superelevation - Iowa Department of Transportation
www.iowadot.govfriction, with a factor of safety to account for variations in the speed, tire conditions, and pavement conditions, is the maximum design friction factor based upon vehicle need. ... Roadways with closed medians (concrete barrier rail) should be superelevated with the axis of
Railway Alignment Design and Geometry
web.engr.uky.edurail” (inside) Function of… Vehicle speed, curve radius and tire side friction (0.01e + f) / (1 – 0.01ef) = V2/15R Function of design speed, degree of curve E = 0.0007V2D – Eu Where Eu is unbalance (1-2” typical) Max. values 6-8% Freight: 6-7” Light Rail: 6” …
Wheel‐Rail Interaction Fundamentals
www.wheel-rail-seminars.com• The contact area at each wheel tread / low rail interface is approximately circular, with a typical radius of 7mm. • The rail steel can be assumed to have a shear yield strength of k=70 ksi. • The rail surface is dry, with a nominal COF of μ= 0.6
SSP 350 – The 3.0l V6 TDI engine
www.volkspage.netThe valves are actuated via low-friction roller rocker fingers with hydraulic valve clearance compensation elements. For the structure and function of the hydraulic valve clearance compensation elements, refer to self-study programme No. 183 "The 2.5l V6 TDI 4V engine". The injectors are secured in the cylinder head with the aid of clamping pieces.
Development of Class 800/801 High-speed Rolling Stock for ...
www.hitachi.comusing friction stir welding (FSW) to create light and strong carbodies with minimal distortion to the exterior. Also, because the trains operate at speeds of 200 km/h or more, the carbodies are air-tight to minimize interior pressure fluctuations and maintain comfort. In the driving cab, the driver’s seat is surrounded