HARDWARE MANUAL - Mitsubishi Electric

1 HARDWARE MANUALFX1S SERIES programmable CONTROLLERSFX1S Series programmable ControllersForeword This MANUAL contains text, diagrams and explanations which will guide the reader in the correct installationand operation of the FX1S Series programmable Controllers. It should be read and understood beforeattempting to install or use the unit. Further information can be found in the FX Series Programming MANUAL II. If in doubt at any stage of the installation of an FX1S Series programmable controller always consult aprofessional electrical engineer who is qualified and trained to the local and national standards which apply tothe installation site.

2 If in doubt about the operation or use of FX1S Series programmable controller please consult your localMitsubishi Electric representative. This MANUAL is subject to change without notice. iFX1S Series programmable ControllersHardware ManualThis MANUAL confers no industrial property rights or any rights of any other kind, nor does it confer any patentlicenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrialproperty rights which may occur as a result of using the contents noted in this Series programmable ControllersManual number : JY992D83901 MANUAL revision : PDate:April 2015FX1S Series programmable ControllersiiGuidelines for the Safety of the User and Protection of the MANUAL provides information for the use of the FX1S.

3 The MANUAL has been written to beused by trained and competent personnel. The definition of such a person or persons is asfollows:a) Any engineer who is responsible for the planning, design and construction of automaticequipment using the product associated with this MANUAL , should be of a competentnature, trained and qualified to the local and national standards required to fulfill thatrole. These engineers should be fully aware of all aspects of safety with regards toautomated ) Any commissioning or service engineer must be of a competent nature, trained andqualified to the local and national standards required to fulfill that job.

4 These engineersshould also be trained in the use and maintenance of the completed product. Thisincludes being completely familiar with all associated documentation for said product. Allmaintenance should be carried out in accordance with established safety ) All operators of the completed equipment (see Note) should be trained to use thisproduct in a safe manner in compliance to established safety practices. The operatorsshould also be familiar with documentation which is associated with the operation of thecompleted equipment.

5 Note :The term completed equipment refers to a third party constructed device whichcontains or uses the product associated with this Series programmable ControllersiiiNotes on the Symbols Used in this ManualAt various times throughout this MANUAL certain symbols will be used to highlight points whichare intended to ensure the users personal safety and protect the integrity of any of the following symbols are encountered its associated note must be read andunderstood. Each of the symbols used will now be listed with a brief description of its Warnings1) Indicates that the identified danger WILL cause physical and property ) Indicates that the identified danger could POSSIBLY cause physical and ) Indicates a point of further interest or further Warnings4) Indicates special care must be taken when using this element of ) Indicates a special point which the user of the associate software element shouldbe )

6 Indicates a point of interest or further Series programmable Controllersiv Under no circumstances will Mitsubishi Electric be liable responsible for any consequentialdamage that may arise as a result of the installation or use of this equipment. All examples and diagrams shown in this MANUAL are intended only as an aid tounderstanding the text, not to guarantee operation. Mitsubishi Electric will accept noresponsibility for actual use of the product based on these illustrative examples. Please contact your local Mitsubishi Electric representative for more information concerningapplications in life critical situations or high Microsoft and Windows are either registered trademarks or trademarks of MicrosoftCorporation in the United States and/or other countries.

7 The company name and the product name to be described in this MANUAL are the registeredtrademarks or trademarks of each Series programmable ControllersvMarine standardThe FX1S Series conforms to the marine standards listed , regulation conformity restrictions on various equipment are reduced when the FX1 SSeries installation setup complies with marine consult with Mitsubishi Electric for the latest information on marine standard practicesand the corresponding types of practice abbreviationStandard practice nameCandidate countryGLGermanischer LloydGermanyRINAREGISTRO ITALIANO NAVALEI talyABSA merican Bureau of ShippingUnited StatesLloydLloyd's Register of ShippingBritainBVBureau VeritasFranceFX1S Series programmable ControllersviNote Concerning the CE

8 MarkingThis note does not guarantee that an entire mechanical module produced in accordance withthe contents of this note will comply with the following standards. Compliance to EMC directiveand LVD directive of the entire mechanical module should be checked by the user /manufacturer. For more details please contact the local Mitsubishi Electric sales logic controllers are open-type devices that must be installed and used withinconductive control use the FX1S Series programmable logic controllers while installed in conductiveshielded control secure the control box lid to the control box (for conduction).

9 Installation within a control box greatly affects the safety of the system and aids in shieldingnoise from the programmable logic Series programmable ControllersviiEMCThe following products have shown compliance through direct testing (of the identifiedstandards below) and design analysis (through the creation of a technical construction file) tothe European Directive for Electromagnetic Compatibility (2004/108/EC) when used asdirected by the appropriate to a MANUAL or related material of each product for details concerning products notincluded This product is designed for use in industrial applications.

10 Authorized Representative in the European Community: Mitsubishi Electric Europe Str. 8, 40880 Ratingen, GermanyFX1S Series programmable ControllersviiiType: programmable controller (Open Type Equipment)Models : MELSEC FX1S series manufacturedfrom March 1st, 2000FX1S- MR-ES/ULfrom September 1st, 2000FX1S- MR-DSFX1S- MT-DSSfrom July 1st, 2001FX1S- MT-ESS/ULWhere indicates:10,14,20,30 Models : MELSEC FX1N series manufacturedfrom March 1st, 2000FX1N-232-BDFX1N-485-BDFX1N-422-BDFX1 N-8AV-BDFX1N-5 DMFX1N-EEPROM-8 LFX1N-CNV-BDfrom June 1st, 2001FX1N-4EX-BDFX1N-2 EYT-BD FX1N-2AD-BDFX1N-1DA-BDModels.