HARTING Selection Guide Han-Modular Connectors

HARTING Industrial Connectors Han Short Form Catalogue

in the automotive industry, or in industrial sensor and actuator applications, RFID and wireless technologies, in addition to pack-aging and housing made of plastics, aluminum and stainless steel. HARTING overcomes technological limitations. Drawing on the comprehensive resources of the group’s technol-

  Industry, Steel, Rfid

HARTING Selection Guide Han-Modular Connectors

HARTING Han-Modular ® Selection Guide Description of the Han-Modular ® system The Han-Modular ® series is designed for combining different transmission media in one connector. The multifaceted system of inserts, contacts, frames, hoods and housings as well as accessories fulfils individual customer requirements.

HARTING M23 Circular Connectors

of materials for inserts and contacts including terminals. The current capacity-curve is valid for continuous, non-interrupted current-loaded contacts of connectors when simultaneous power on all contacts is given, without exceeding the maximum temperature. Control and testing procedures, according to DIN IEC 60512-5-2.

  Contact, Connectors

M12 SteckverbinderAnschluss- und Verbindungstechnik ...

Varianten vor allem im IP20-Bereich . Daneben wer-den durch den Einsatz entsprechender Schutzge-häuse die RJ45-Verbinder auch für den Einsatz im IP65 / IP67-Umfeld ertüchtigt . Das sind dann: • RJ45 Han® PushPull (PROFINET Schnittstelle) • RJ45 Han® 3 A (quasi Standard in der Industrie, PROFINET Schnittstelle)

  Ip20

PC 707 Crimper - Gates Corporation

the crimp OD. Insert the coupling into the die set approximately 1/8” below top of die. (See Photo 1.) Slide the die cone assembly under the ram until it stops against back locating pins and push the crimp button and hold. Release the button immediately when the pump stops. Remover coupling and measure crimp diameter, which

  Corporation, Gate, Crimp, Gates corporation

DMC Crimp Dies For a Full Range of Capabilities

DMC Crimp Dies For a Full Range of Capabilities DMC constantly adds new crimp die designs that are comparable to connector and terminal supplier dies or tools. A few of the popular die applications are featured in the following charts. For more options, consult factory .

  Crimp

MIL-DTL-83513/03 & /04 Micro-D Pre-Wired Crimp …

Pre-Wired Crimp Terminated, Metal Shell Connector Micro-D Pre-Wired Pigtails These connectors feature gold-plated TwistPin contacts and mil spec crimp termination. Specify aluminum shells for best availability. 100% tested and backpotted, ready for use. Choose the Wire Type To Fit Your Application

  Crimp

Series 801 Mighty Mouse Double-Start ACME Thread ...

1.ontacts are crimp type, C and used in a rear release retention system 2. Receptacle mates with all quick coupling high density receptacle connectors with same polarization and opposite contact gender 3. Connectors supplied with standard crimp contacts. For coax or other special contacts, order connector less contacts (Contact style

  Crimp

WINEGARD Gateway

crimp splice, and slide the black ground wire from the Gateway into the opposite end of the splice. Crimp the splice. Step 12 – Mount the wall plate to the wall or panel with the two supplied wall plate screws. Step 13 – Next, connect the WiFi cable with the red tubing to the mating connector that is designated in the #2 slot.

  Getaways, Crimp, Winegard, Winegard gateway

Ideal for…

N Male Right Angle EZ-400-NMH-RA-X 3190-2638 <1.35:1 (6) Hex/KnurlSpring Finger Crimp A/G 1.87 (47) 1.42 (36.0) 0.177 (80.2) 28. N Male Right Angle TC-400-NMH-RA-SS 3190-1668 <1.25:1 (2.5) Hex Solder Crimp SS/G 1.5 (38.1) 0.89 (2.6) 0.130 (59.0) 29.

  Crimp

CRIMP TOOL AND ACCESSORY ASSEMBLY TOOLS SIZE …

crimp tool and accessory assembly tools mating end wire barrel af8 afm8 mh860 39-00 wa23 (pos) wa23 (die) installing removal 1 amphenol corp. robert technologies typical contact configuration 6 6n 6 6 p p m39029/48-317 m39029/48-318 ms90559-11 ms90559-12 6 6 wa23-10 wa23-10 wa23-3 wa23-3 by hand by hand drk178-6a

  Crimp