HELPFUL TIPS TROUBLESHOOTING PROBLEM POSSIBLE …

1 OPERATING INSTRUCTIONSHELPFUL tips Make sure the receiver is plugged into a working AC outlet. Make sure the receiver and connected equipment are on. Make sure the remote control ON button is pushed. Make sure the battery in the remote control is still CONTROL OUTLETSITEM #0141479 MODEL #UTTNRC211. Remove the plastic battery tab from the battery compartment in the back of the remote control to activate the pre-installed Plug the receiver into a grounded, 3-wire indoor outlet, making sure there is power to the outlet the receiver is plugged into. 3. Plug the lights or devices to be controlled into the Press the ON/OFF buttons on the remote control to turn the lights or devices on or off. The red indicator light on the receiver is lit when the unit is powered REPLACEMENTUse your finger to slide out the battery holder on the left bottom corner of the remote.

2 Remove the spent battery and insert a new CR2032, 3V button-cell battery with the + polarity mark facing up. Slide the battery holder back inside. Dispose of the old battery in compliance with all applicable laws. Contact your local solid waste authority for detailed information. Non-rechargeable batteries are not to be : DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR SUPPLIER: Changzhou Rihui Battery Co., Ltd. Printed in ChinaFCC REGULATORY STATEMENTThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

3 These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3.

4 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for : CHOKING HAZARD Small Parts. Not for children under 3 years.!14 SAFETY INFORMATIONThis is a GROUNDED device. The male plug contains a ground pin and is only intended for use with a three-pronged grounded device is for use with a 125 V AC power source. 125 V AC / 60 HzDo not attach a device that exceeds the unit ratings: 15 A / 1,875 W Resistive (General Purpose)5 A / 625 W Tungsten (Incandescent)Call customer service at 1-866-994-4148,8 - 6 , EST, Monday - Thursday, 8 - 5 , EST, plugged into the receiver is not lights are not in ON position, they are not functioning, remote is not receiving power or remote control ON button is not the connected lights are functional by plugging them directly into the outlet.

5 Be sure the connected lights are in the ON position if they have their own switch. Make sure the outlet the receiver is plugged into is active. Make sure the remote control ON button is pushed. Replace the CR2032, 3V battery in the remote POSSIBLE CAUSECORRECTIVE ACTION

6 32IC REGULATORY STATEMENTU nder Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power ( ) is not more than that necessary for successful device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

7 Impreso en ChinaP INSTRUCCIONES DE FUNCIONAMIENTOCONSEJOS PR CTICOS Aseg rese de que el

8 Receptor est enchufado a un tomacorriente de CA funcional. Aseg rese de que el receptor y el equipo conectado est n encendidos. Aseg rese de que el bot n de ENCENDIDO del control remoto est presionado. Aseg rese de que la bater a del control remoto est PARA CONTROL REMOTOART CULO #0141479 MODELO #UTTNRC211. Retire la pesta a de pl stico de la bater a del compartimiento de la bater a en la parte posterior del control remoto para activar la bater a Enchufe el receptor en un tomacorriente para interiores con puesta a tierra de 3 conductores, asegur ndose de que haya alimentaci n hacia el tomacorriente al que est enchufado el receptor. 3. Enchufe las luces o dispositivos que va a controlar en el Presione los botones de ENCENDIDO/APAGADO en el control remoto para encender o apagar las luces y los dispositivos.

9 La luz indicadora roja en el receptor se enciende cuando la unidad recibe alimentaci DE LAS BATER ASUse el dedo para deslizar el soporte de la bater a en la esquina inferior derecha del control remoto. Retire la bater a usada e inserte una bater a de bot n CR2032 de 3 voltios nueva con la marca de polaridad + hacia arriba. Deslice el soporte de la bater a de vuelta en el control remoto. Elimine la bater a antigua seg n las leyes aplicables. Para obtener informaci n detallada, p ngase en contacto con su autoridad de eliminaci n de desechos s lidos local. Las bater as que no son recargables no deben : NO INCINERE LAS BATER AS. LAS BATER AS PODR AN EXPLOTAR O DE BATER AS: Changzhou Rihui Battery Co., : RIESGO DE ASFIXIA: Piezas peque as. No es adecuado para ni os menores de 3 a os.

10 !INFORMACI N DE SEGURIDAD Este es un dispositivo con PUESTA A TIERRA. El enchufe macho contiene una clavija de puesta a tierra y est destinada solo para su uso con un tomacorriente de puesta a tierra de tres es para uso con una fuente de alimentaci n de 125 v V CA / 60 HzNo conecte un dispositivo que supere la clasificaci n de la unidad:15 amperios / 1875 vatios resistivo (para uso general)5 amperios / 625 vatios tungsteno (incandescente)El equipo enchufado al receptor no luces conectadas no est n en la posici n de ENCENDIDO, no funcionan, el control remoto no recibe alimentaci n o el bot n de ENCENDIDO del control remoto no est rese de que las luces conectadas funcionan enchuf ndolas directamente al tomacorriente. Aseg rese de que las luces conectadas est n en la posici n de encendido si tienen su propio interruptor. Aseg rese de que el tomacorriente al cual est enchufado el receptor est energizado.