Hilti HIT-HY 70 injection mortar for masonry
Rotary hammer TE2 – TE16 Other tools blow out pump, set of cleaning brushes, dispenser. Hilti H-H 70 July 2014 page 257 Setting instructions in solid base materials . Hilti H-H 70 page 258 July 2014 Setting details: hole depth h 0 and effective anchorage depth in solid base materials
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
HSL-3 EXPANSION ANCHOR - Hilti
www.hilti.com.auHSL-3 expansion anchor Ultimate-performance heavy-duty expansion anchor Anchor versions Benefits (M8 HSL-3 Bolt version -M24) - Suitable for cracked concrete C20/25 to C50/60 - Suitable for all dynamic loads: seismic C1 and C2, shock and fatigue - Can be installed with hammer or diamond drilling for same performance
Expansion, Anchor, Expansion anchor, Expansion anchor anchor
Technical Data Sheet for HIT RE-500 V3 Injectable Mortar ...
www.hilti.com.auAll data in this section applies to: - Correct setting (See setting instruction) - No edge distance and spacing influence - Steel failure - HAS-U anchor rod with strength class 5.8 and 8.8, AM anchor rod with strength class 8.8, HIS-N internally threaded insert with screw 8.8 - Base material thickness, as specified in the table
Chemical anchoring systems. - Hilti
www.hilti.com.aupage 62 February 2014 HV with HA- rod adhesive anchor STEP 2: SHEAR LOADING The design shear resistance VRd is the lower of: Design Concrete Edge Resistance VRd,c = fB • V*Rd,c V*Rd,c is obtained from the relevant design table f B influence of concrete strength Concrete Strengths f’c,cyl (MPa) 20 25 32 40 50 fB 0.79 0.87 1.00 1.11 1.22 Shear load acting parallel to …
Hilti HIT-HY 200 with HIT-V
www.hilti.com.au(Hilti HIT-HY 200-R) Fire test report IBMB, Brunswick 3501/676/13 / 2012-08-03 a) All data given in this section according ETA-12/0084, issue 2013-06-20. Service temperature range Hilti HIT-HY 200 injection mortar may be applied in the temperature ranges given below. An elevated base material temperature
HIT-RE 500 with HIT-V / HAS rods - Hilti
www.hilti.com.auOne anchor material, as specified in the tables Non cracked concrete f c,cyl = 32 MPa Temperate range I (min. base material temperature -40°C, max. long term/short term base material temperature: +24°C/40°C) Installation temperature range +5°C to +40°C Embedment depth and base material thickness for the basic loading data Recommended loads
Related documents
HVU with HAS/HAS-E rod adhesive anchor
www.hilti.comRotary hammer . TE 2 – TE 16 . TE 40 – TE 70 . Other tools . blow out pump or compressed air gun, setting tools . Setting instruction . Dry and water-saturated concrete, hammer drilling. For detailed information on installation see instruction for use given with the package of the product.
11.25 Clay Processing - US EPA
www3.epa.govThe shredded material then is either dried or ground in a hammer mill. Material exiting the hammer mill is mixed with water and bulk loaded as a slurry for shipping. Figure 11.25-3 depicts the process flow for ball clay processing. Indirect rotary or vibrating grate dryers are used to dry ball clay. Combustion gases from the
APPENDIX MUSICAL INSTRUMENTS & ENSEMBLES
wmich.eduNov 02, 2007 · The modern "rotary" valve was invented in the early Romantic period (c. 1830)—an invention that made the brass family more responsive and ... mallet, a stick, or a hammer) in order to produce a musical sound. Composers have made greater use of percussion color in their scores since the 1880s. Percussion instruments fall into
RUGER MODEL 10/22 CARBINE - textfiles.com
pdf.textfiles.comshot rotary magazine. Retracting the bolt handle cocks the internal hammer and compresses the recoil spring. When the bolt is manually released, it moves forward (driven by the recoil spring), strips a cartridge from the magazine, if a loaded magazine is in place, and chambers the cartridge. The bolt is held against
G3 Armorer's Manual - textfiles.com
pdf.textfiles.complastic hammer. ¾ Clamp barrel with receiver into vice and check guide in the receiver for smooth operation of bolt assembly by means of “GO” and symmetry gauge. ... ¾ If necessary, replace rotary rear sight (3) (spare parts set 4). ¾ Check if front sight (21) is securely seated in the front sight holder, if necessary, replace
The DIY STEN Gun - noblogs.org
elcombate.noblogs.orgA rotary tool or Dremel is highly useful for delicate grinding and cutting operations. Fitted with a 'reinforced cutting disc' it becomes a mini angle grinder, ideal for cutting out and grinding ... out with a screw driver and hammer. Once the main bulk of material is removed, the remaining lower section is cut off at a marked
11.13 Glass Fiber Manufacturing
www3.epa.govindustry. In the rotary spin process, depicted in Figure 11.13-2, centrifugal force causes molten glass to flow through small holes in the wall of a rapidly rotating cylinder to create fibers that are broken into pieces by an air stream. This is the newer …
Kinetix TLP Multi-purpose Servo Motors with 046. . . 235 ...
literature.rockwellautomation.com• See Kinetix Rotary Motion Specifications Technical Data, publication KNX-TD001, for Bulletin 2090 cables with environmen tally sealed connectors compatible with these motors. Couplings and Pulleys Mechanical connections to the motor shaft, such as couplings and pulleys, require a to rsionally rigid coupling or a reinforced timing belt.
Wireless Endoscope User Manual
images-na.ssl-images-amazon.com3. The unit is not shock-resistant. Do not use it as a hammer and avoid high impact result from things such as dropping the unit from height. 4. Do not use the camera if condensation fogs inside the lens. Let the water evaporate before using again. 5. Turn off the system if it is not in use. 1 Please read the user manual carefully before using ...