HP Storm Pipe
Installation shall be in accordance with ASTM D2321 and ADS recommended installation guidelines, with the exception that minimum cover in traffic areas for 12– through 48–inch (300 to 1200 mm) diameters shall be one foot (0.3 m) and for 60–inch (1500 mm) diameters, the minimum cover shall be 2 feet (0.6 m) in single run applications.
Tags:
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Documents from same domain
ADS HP STORM 12”- 60” PIPE SPECIFICATION
assets.ads-pipe.comAppropriate safety precautions must be used when field-testing any pipe material. Contact the manufacturer for recommended leakage rates. ... Backfill for minimum cover situations shall consist of Class 1 (compacted), Class 2 (minimum ... website at www.ads-pipe.com for a copy of the latest installation guidelines. Pipe Dimensions Nominal Pipe ...
ADS N-12 PLAIN END PIPE (PER ASTM F2648) SPECIFICATION
assets.ads-pipe.comInstallation shall be in accordance with ASTM D2321 and ADS recommended installation guidelines, with the exception that minimum cover in trafficked areas for 4- through 48-inch (100 to 1200 mm) diameters shall be one foot (0.3 m) and for 60-inch (1500 mm) diameter the minimum cover shall be 2 ft. (0.6 m) in single run applications.
6-0 RETENTION/DETENTION SYSTEMS - assets.ads-pipe.com
assets.ads-pipe.comusing either larger diameter corrugated polyethylene pipe and a shorter overall system length, or by using smaller diameter pipe and a longer system length. The final decision depends on the size of the site, its groundwater level, and cover requirements. Figure 6-2 shows a typical cross-section of a retention/detention system. Table 6-2
System, Retention, Pipe, Detention, Corrugated, 6 0 retention detention systems
ADS N-12 WT IB PIPE (PER ASTM F2648) SPECIFICATION
assets.ads-pipe.comFittings Fittings shall conform to ASTM F2306. Bell and spigot connections shall utilize a welded bell and valley or saddle gasket meeting the watertight joint performance requirements of ASTM F2306. Field Pipe and Joint Performance To assure watertightness, field performance verification may be accomplished by testing in accordance with ASTM ...
Specification, Astm, Fitting, Pipe, Watertight, Fittings fittings, Per astm f2648, F2648
Pipe
assets.ads-pipe.comkPa) pressure testing requirements of ASTM D3212. Selection includes couplers, tees, wyes, elbows, caps and adaptors, each fitted with a rubber gasket. The fittings connect not only to corrugated HDPE pipe, but can adapt to PVC, concrete and other materials. inStallation Recommendation S
ADS N-12 WT IB PIPE (PER AASHTO) SPECIFICATION
assets.ads-pipe.comMaterial for pipe and fitting production shall be high-density polyethylene conforming with the minimum requirements of cell classification 424420C for 4- through 10-inch (100 to 250 mm) diameters, and 435400C
ADS N-12 ST IB PIPE (ASTM F2648) SPECIFICATION
assets.ads-pipe.comThis specification describes 4- through 60-inch (100 to 1500 mm) ADS N-12 ST IB pipe (per ASTM F2648) for use in gravity-flow land drainage applications. Pipe Requirements ADS N-12 ST IB pipe (per ASTM F2648) shall have a smooth interior and annular exterior corrugations. • 4- through 60-inch (100 to 1500 mm) pipe shall meet ASTM F2648.
Specification, Astm, Pipe, Per astm f2648, F2648, Astm f2648
N-12 ST IB Pipe (per AASHTO)
assets.ads-pipe.comPipe Requirements ADS N-12 ST IB pipe (per AASHTO) shall have a smooth interior and annular exterior corrugations. • 4- through 10-inch (100 to 250 mm) shall meet AASHTO M252, Type S or SP • 12- through 60-inch (300 to 1500 mm) pipe shall meet AASHTO M294, Type S …
Pure Basin & Curb Inlet Filters
assets.ads-pipe.comInlet Filters Pure basin and curb inlet filters are the preferred choice for permanent inlet protection and stormwater runoff control. Constructed of versatile stainless steel, Pure inlet filters will fit any drainage structure and are available with site-specific filter bags providing various levels of filtration. Applications • Car washes
ADS SINGLE WALL PIPE SPECIFICATION
assets.ads-pipe.com*Pipe O.D. values are provided for reference purposes only, values stated for 12 through 24-inch are ±1 inch. Contact a sales representative for exact values **All diameters available with or without perforations.
Specification, Walls, Single, Pipe, Pipe o, Ads single wall pipe specification
Related documents
GUIDELINES FOR THE DESIGN OF FLEXIBLE PAVEMENTS …
law.resource.orgThis document is revision of the IRC:SP:72-2007 “Guidelines for the Design of Flexible Pavements for Low Volume Roads”. The need for the revision arose to include design charts using stabilized base and sub – base courses as also to enable design of rural roads for trafficvolume upto 2 MSA.
Guidelines, Design, Flexible, Pavement, Guidelines for the design of flexible pavements
IRC:15-2017
law.resource.orgPavements” ix) IRC:SP:46 “Guidelines for Design and Construction of Fibre Reinforced Concrete Pavements” x) IRC:SP:49 “Guidelines for the Use of Dry Lean Concrete as Sub-Base for Rigid Pavement” xi) IRC:SP:76 “Guidelines for Conventional and Thin Whitetopping” xii) IRC:SP:83 “Guidelines for Maintenance, Repairs and Rehabilitation of
Polymer-Modified Asphalt 101 - Pavements/Materials …
pavement.engineering.asu.eduNov 12, 2014 · thinner pavements, thus reducing the service life of the pavement. To meet new Superpave design specifications. Distresses in Asphalt Pavements • High Temperature Permanent Deformation • Low Temperature Thermal Cracking ... Lower G* at low T – flexible
Design, Flexible, Modified, Pavement, Polymer, Asphalt, Polymer modified asphalt 101
Design Guidelines - Pavement Design
www.moretonbay.qld.gov.auDesign Manual Design Guidelines - DG 05 - Pavement Design March 2008 1.0.0 INTRODUCTION 1.1.0 PURPOSE To outline the minimum requirements for subgrade evaluation and structural design of street and road pavements within Pine Rivers Shire. To accumulate a database of test results which will lead to a more efficient determination of
Advisory of Transportation Circular
www.faa.govearthwork, flexible base courses, rigid base courses, flexible surface courses, rigid pavement, fencing, drainage, turf, and lighting installation. 2 Cancellation. This AC cancels AC 150/5370-10G, Standards for Specifying Construction of Airports, dated July 21, 2014. 3 Application.
Table of Contents
www.ipswichplanning.com.auPlanning Scheme Policy 3—General Works, Part 1—Roadworks November 2017 PSP3-1 PLANNING SCHEME POLICY 3—GENERAL WORKS PART …